Weed Eater 545186731 instruction manual Maintenance

Page 8

MAINTENANCE

WARNING: Disconnect the spark plug before performing maintenance except for carburetor adjustments.

HELPFUL TIP

IMPORTANT: Have all

repairs other than the rec- ommended maintenance described in the instruction manual performed by an authorized service dealer.

If any dealer other than an authorized service dealer performs work on the product, WEED EATER may not pay for repairs under warranty. It is your re- sponsibility to maintain and perform general maintenance.

GENERAL RECOMMENDATIONS

The warranty on this unit does not cover items that have been subjected to operator abuse or negligence. To receive full value from the warranty, the operator must maintain unit as instructed in this manual. Various adjust- ments will need to be made periodically to properly maintain your unit.

SOnce each year, replace the spark plug, re- place air filter element and check blade for wear. A new spark plug and a clean/new air filter element assures proper air/fuel mix- ture and helps your engine run better and last longer.

CHECK FOR DAMAGED OR WORN PARTS

Contact an authorized service dealer for re- placement of damaged or worn parts.

SON/OFF Switch -- Ensure ON/OFF switch functions properly by moving the switch to

the OFF position and assure the engine stops; then restart engine and continue.

SFuel Tank -- Discontinue use of edger if fuel

tank shows signs of damage or leaks.

SBlade Guard -- Discontinue use of edger if blade guard is damaged.

CHECK FOR LOOSE

FASTENERS AND PARTS

SBlade nut S Muffler

S Cylinder shield S Clutch

S Throttle trigger S Handle screws S Fasteners

INSPECT AND CLEAN UNIT & LA- BELS

S After each use, inspect complete unit for loose or damaged parts. Clean the unit and labels using a damp cloth with a mild deter- gent.

SWipe off unit with a clean dry cloth.

CLEAN AIR FILTER

A dirty air filter decreases the life and perfor- mance of the engine and increases fuel con- sumption and harmful emissions.

Always clean your air filter after 5 tanks of fuel or 5 hours of operation, whichever comes first. Clean more frequently in dusty condi- tions. It is advisable to replace your air filter with a new one after every 50 hours of opera- tion, or annually, whichever comes first.

To clean filter:

1. Clean the cover and the area around it to keep dirt from falling into the carburetor chamber when the cover is removed.

2. Remove the two screws and the air filter cover from the engine.

3. Remove air filter.

NOTE: Do not clean the air filter with gaso- line or other flammable solvent to avoid creat- ing a fire hazard or producing harmful evapo- rative emissions.

4.Clean the air filter using hot soapy water. Rinse with clean cool water. Air dry com- pletely before reinstalling.

5.Lightly oil air filter before installing to im- prove the efficiency of the air filter. Use 2--cycle engine oil or motor oil (SAE 30).

NOTE: Do not soak air filter in oil.

6.Squeeze the air filter to distribute oil and to remove any excess oil.

7.Reinstall air filter in housing. CAUTION: Make sure air filter is fitted in to the corners of the housing to prevent air from bypassing the filter and to keep dust from en- tering engine and causing damage.

8.Reinstall air filter cover.

Air Filter

Cover

Cover

Screws

BLADE MAINTENANCE

WARNING: The blade will continue to spin after the engine stops or after the throttle trigger has been released. Make sure the blade has stopped coasting and discon- nect the spark plug before performing work on the blade.

WARNING: Wear protective gloves when handling or performing maintenance on the blade to help avoid injury.

Always replace a blade that is bent, warped, cracked, broken, or damaged in any other way. Never attempt to straighten and reuse a damaged blade. Use only specified replace- ment blade.

SThe blade is reversible. When the cutting edge on one side becomes worn, turn the blade over.

SCheck blade for flatness periodically. Lay the blade on a flat surface to inspect for flat- ness. Throw away a blade that is not flat.

8

Image 8
Contents Manual de Instrucciones Manuel d’Instructions Safety Rules Operator SafetyUnit Safety Edging SafetySpecial Notice This unit is not Fuel SafetyTransporting and Storage Assembly Tube AssemblyAdjustable wrench Hex wrench provided Examine parts for damage. Do not use dam- aged partsOperation Stopping Your Engine Starting Your EngineStarting a Warm Engine Starting PositionSetting the Edging Depth Starting a Flooded EngineEdging To set the depthMaintenance Service and Adjustments Blade ReplacementTo adjust idle speed Carburetor Idle Speed AdjustmentSeasonal Storage Fuel SystemEngine OtherTroubleshooting Table Cause Remedy Canada, contact Ligations The U.S. EnvironmentalIntermediate 125 hours Extended 300 hours