Weed Eater WET2242STD manual To Level Mower Housing, To Replace Mower Blade Drive Belt See Fig

Page 19

SERVICE AND ADJUSTMENTS

TO LEVEL MOWER HOUSING

Adjust the mower while tractor is parked on level ground or driveway. Make sure tires are properly inflated (See “PRODUCT SPECIFICATIONS” section of this manual). If tires are over or underinflated, you will not properly adjust your mower.

SIDE-TO-SIDE ADJUSTMENT (See Figs. 14 and 15)

•Raise mower to its highest position.

•At the midpoint of both sides of mower, measure height from bottom edge of mower to ground. Distance “A” on both sides of mower should be the same or within 1/4" of each other.

•If adjustment is necessary, make adjustment on one side of mower only.

•To raise one side of mower, tighten lift link adjustment nut on that side.

•To lower one side of mower, loosen lift link adjustment nut on that side.

NOTE: Each full turn of adjustment nut will change mower height about 1/8".

•Recheck measurements after adjusting.

BOTTOM EDGE

 

BOTTOM EDGE

OF MOWER TO

 

OF MOWER TO

GROUND

 

GROUND

A

GROUND LINE

A

FIG. 14

SUSPENSION ARM

LIFT LINK

ADJUSTMENT NUT

FIG. 15

FRONT-TO-BACK ADJUSTMENT (See Figs. 16 and 17)

IMPORTANT: DECK MUST BE LEVEL SIDE-TO-SIDE. IF THE FOLLOWING FRONT-TO-BACK ADJUSTMENT IS NECESSARY, BE SURE TO ADJUST BOTH FRONT LINKS EQUALLY SO MOWER WILL STAY LEVEL SIDE-TO-SIDE.

To obtain the best cutting results, the mower housing should be adjusted so that the front is approximately 1/8" to 1/2" lower than the rear when the mower is in its high- est position.

Check adjustment on right side of tractor. Measure distance “D” directly in front and behind the mandrel at bottom edge of mower housing as shown.

•Before making any necessary adjustments, check that both front links are equal in length.

•If links are not equal in length, adjust one link to same length as other link.

•To lower front of mower loosen nut “E” on both front links an equal number of turns.

•When distance “D” is 1/8" to 1/2" lower at front than rear, tighten nuts “F” against trunnion on both front links.

•To raise front of mower, loosen nut “F” from trunnion on both front links. Tighten nut “E” on both front links an equal number of turns. The two front links must remain equal in length.

•When distance “D” is 1/8" to 1/2" lower at front than rear, tighten nut “F” against trunnion on both front links.

•Recheck side-to-side adjustment.

MANDREL

“D”

“D”

FIG. 16

BOTH FRONT LINKS MUST BE EQUAL IN LENGTH

NUT “F”

NUT “E”

TRUNNION

FRONT LINKS

FIG. 17

TO REPLACE MOWER BLADE DRIVE BELT (See Fig. 18)

The mower blade drive belt may be replaced without tools. Park the tractor on level surface. Engage parking brake.

BELT REMOVAL -

•Remove mower from tractor (See “TO REMOVE MOWER” in this section of this manual).

•Work belt off both mandrel pulleys and idler pulleys.

•Pull belt away from mower.

BELT INSTALLATION -

•Install new belt in reverse order of removal.

•Make sure belt is in all pulley grooves and inside all belt guides.

•Install mower in reverse order of removal instruc- tions.

19

Page 18 Page 20
Image 19
Page 18 Page 20
Contents Model NO. WET2242STD Safety Rules Safety Rules Table of Contents Contents of Hardware Pack Before Removing Tractor from Skid AssemblyTools Required for Assembly To Remove Tractor from CartonCheck Battery See Fig Install Seat See FigCheck Brake System Check Tire PressureCheck Deck Levelness Check for Proper Position of ALL BeltsOperation Know Your Tractor HOW to USE Your Tractor Before Starting the Engine To Start Engine See Fig Mowing TipsBefore Each USE MaintenanceLubrication Chart General RecommendationsTractor Engine IN-LINE Fuel Filter See Fig CleaningMuffler Spark PlugsTo Install Mower See Fig Service and AdjustmentsTo Remove Mower See Fig Belt Removal To Level Mower HousingBelt Installation To Replace Mower Blade Drive Belt See FigTo Check Brake To Check and Adjust Brake See FigTo Adjust Brake To Replace Motion Drive Belt See FigTo Remove Wheel for Repairs See Fig Transaxle Gear Shift Lever NEUTRAL- Adjustment See FigTo Adjust Steering Wheel ALIGN- Ment Front Wheel TOE-IN/CAMBERInterlocks and Relays To Replace Headlight BulbTo Replace Fuse To Adjust Choke Control To Adjust Throttle Control CableTo Adjust Carburetor Engine OIL StorageOther Fuel SystemTroubleshooting Points With attachment clutch Tractor - Model Number WET2242STD SchematicElectrical 183759 144927Chassis and Enclosures 174714 179174X01017 183394X550 Hood 126938X 183552Drive 17490510 17393774490544 72110622Steering Assembly 72110618 40 73540600 Nut 186737188967 Engine 184900 180186 Seat Assembly188704 180166Decals Mower Lift Repair Parts Mower Deck 187690 7390060019091210 188234Service Notes Limited Warranty Policy Only Ride UP and Down Hill Not Across Hill Degrees MAX Suggested Guide for Sighting Slopes for Safe Operation

WET2242STD specifications

The Weed Eater WET2242STD is a powerful and versatile string trimmer designed to meet the needs of both homeowners and landscape professionals. This reliable tool offers a perfect blend of performance, ease of use, and innovative features that make it an excellent choice for tackling even the toughest yard maintenance tasks.

One of the standout features of the WET2242STD is its robust 22cc, 2-cycle engine. This powerful engine provides ample power to cut through dense vegetation, making it an ideal choice for trimming grass, weeds, and overgrown areas. The engine's lightweight design contributes to reduced fatigue during extended use, allowing operators to work comfortably for longer periods.

The trimmer features an adjustable curved shaft, which ensures versatility in handling different tasks while providing optimal balance and reduced vibration. This design allows users to easily maneuver around flower beds, rocks, and other obstacles, making trimming more efficient and enjoyable. The WET2242STD also incorporates a dual-line feed system, which automatically advances the cutting line as needed, ensuring consistent cutting performance without interruptions.

Durability is a key characteristic of the WET2242STD. Its high-quality construction is built to withstand the rigors of regular use, featuring components that are resistant to wear and tear. The trimmer is also equipped with a protective shield that enhances safety while providing protection against debris.

In terms of technology, the WET2242STD utilizes an easy-start system that simplifies the process of getting the unit running, reducing the time and effort required to start the engine. This feature is especially beneficial for those who may be new to using string trimmers, as it minimizes frustration and ensures a quick start-up with minimal fuss.

Another noteworthy aspect of the WET2242STD is its user-friendly design. The trimmer is equipped with an ergonomic handle that provides a comfortable grip and reduces strain on the hands during operation. This thoughtful design feature enhances user control and precision when navigating around tight spaces.

Overall, the Weed Eater WET2242STD is a reliable, high-performance string trimmer that combines an efficient engine with user-friendly features. Its lightweight design, adjustable shaft, and automatic line feed system make it an excellent addition to any lawn care toolkit. Whether you're a homeowner looking to maintain your yard or a professional landscaper, the WET2242STD delivers impressive results with every use.
Top Page Image Contents