Weed Eater WET2242STD manual Storage, Other, Fuel System, Engine OIL, Cylinders

Page 24

STORAGE

Immediately prepare your tractor for storage at the end of the season or if the tractor will not be used for 30 days or more.

WARNING: Never store the tractor with gasoline in the tank inside a building where fumes may reach an open flame or spark. Allow the engine to cool before storing in any enclosure.

TRACTOR

Remove mower from tractor for winter storage. When mower is to be stored for a period of time, clean it thoroughly, remove all dirt, grease, leaves, etc. Store in a clean, dry area.

•Clean entire tractor (See “CLEANING” in the Mainte- nance section of this manual).

•Inspect and replace belts, if necessary (See belt re- placement instructions in the Service and Adjustments section of this manual).

•Lubricate as shown in the Maintenance section of this manual.

•Be sure that all nuts, bolts and screws are securely fastened. Inspect moving parts for damage, breakage and wear. Replace if necessary.

•Touch up all rusted or chipped paint surfaces; sand lightly before painting.

BATTERY

•Fully charge the battery for storage.

•After a period of time in storage, battery may require recharging.

•To help prevent corrosion and power leakage during long periods of storage, battery cables should be dis- connected and battery cleaned thoroughly (see “TO CLEAN BATTERY AND TERMINALS” in the Mainte- nance section of this manual).

•After cleaning, leave cables disconnected and place cables where they cannot come in contact with battery terminals.

•If battery is removed from tractor for storage, do not store battery directly on concrete or damp surfaces.

ENGINE

FUEL SYSTEM

IMPORTANT: IT IS IMPORTANTTO PREVENT GUM DEPOSITS FROM FORMING IN ESSENTIAL FUEL SYSTEM PARTS SUCH AS CARBURETOR, FUEL FILTER, FUEL HOSE, OR TANK DURING STORAGE. ALSO, EXPERIENCE INDICATES THAT ALCOHOL BLENDED FUELS (CALLED GASOHOL OR USING ETHANOL OR METHANOL) CAN ATTRACT MOISTUREWHICH LEADSTO SEPARATION AND FORMATION OF ACIDS DURING STORAGE. ACIDIC GAS CAN DAMAGE THE FUEL SYSTEM OF AN ENGINE WHILE IN STORAGE.

•Empty the fuel tank by starting the engine and let it run until the fuel lines and carburetor are empty.

•Never use engine or carburetor cleaner products in the fuel tank or permanent damage may occur.

•Use fresh fuel next season.

NOTE: Fuel stabilizer is an acceptable alternative in mini- mizing the formation of fuel gum deposits during storage. Add stabilizer to gasoline in fuel tank or storage container. Always follow the mix ratio found on stabilizer container. Run engine at least 10 minutes after adding stabilizer to allow the stabilizer to reach the carburetor. Do not empty the gas tank and carburetor if using fuel stabilizer.

ENGINE OIL

Drain oil (with engine warm) and replace with clean en- gine oil. (See “ENGINE” in the Maintenance section of this manual).

CYLINDER(S)

•Remove spark plug(s).

•Pour one ounce of oil through spark plug hole(s) into cylinder(s).

•Turn ignition key to “START” position for a few seconds to distribute oil.

•Replace with new spark plug(s).

OTHER

•Do not store gasoline from one season to another.

•Replace your gasoline can if your can starts to rust. Rust and/or dirt in your gasoline will cause problems.

•If possible, store your tractor indoors and cover it to give protection from dust and dirt.

•Cover your tractor with a suitable protective cover that does not retain moisture. Do not use plastic. Plastic cannot breathe which allows condensation to form and will cause your tractor to rust.

IMPORTANT: NEVER COVERTRACTOR WHILE ENGINE AND EXHAUST AREAS ARE STILL WARM.

24

Page 23 Page 25
Image 24
Page 23 Page 25
Contents Model NO. WET2242STD Safety Rules Safety Rules Table of Contents Contents of Hardware Pack Assembly Tools Required for AssemblyTo Remove Tractor from Carton Before Removing Tractor from SkidInstall Seat See Fig Check Battery See FigCheck Tire Pressure Check Deck LevelnessCheck for Proper Position of ALL Belts Check Brake SystemOperation Know Your Tractor HOW to USE Your Tractor Before Starting the Engine Mowing Tips To Start Engine See FigMaintenance Lubrication ChartGeneral Recommendations Before Each USETractor Engine Cleaning MufflerSpark Plugs IN-LINE Fuel Filter See FigService and Adjustments To Install Mower See FigTo Remove Mower See Fig To Level Mower Housing Belt InstallationTo Replace Mower Blade Drive Belt See Fig Belt RemovalTo Check and Adjust Brake See Fig To Adjust BrakeTo Replace Motion Drive Belt See Fig To Check BrakeTransaxle Gear Shift Lever NEUTRAL- Adjustment See Fig To Adjust Steering Wheel ALIGN- MentFront Wheel TOE-IN/CAMBER To Remove Wheel for Repairs See FigTo Replace Headlight Bulb Interlocks and RelaysTo Replace Fuse To Adjust Throttle Control Cable To Adjust Choke ControlTo Adjust Carburetor Storage OtherFuel System Engine OILTroubleshooting Points With attachment clutch Schematic Tractor - Model Number WET2242STDElectrical 144927 183759Chassis and Enclosures 179174X010 17 183394X550 Hood 126938X183552 174714Drive 173937 7449054472110622 17490510Steering Assembly 40 73540600 Nut 186737 72110618188967 Engine 184900 Seat Assembly 188704180166 180186Decals Mower Lift Repair Parts Mower Deck 73900600 19091210188234 187690Service Notes Limited Warranty Policy Suggested Guide for Sighting Slopes for Safe Operation Only Ride UP and Down Hill Not Across Hill Degrees MAX

WET2242STD specifications

The Weed Eater WET2242STD is a powerful and versatile string trimmer designed to meet the needs of both homeowners and landscape professionals. This reliable tool offers a perfect blend of performance, ease of use, and innovative features that make it an excellent choice for tackling even the toughest yard maintenance tasks.

One of the standout features of the WET2242STD is its robust 22cc, 2-cycle engine. This powerful engine provides ample power to cut through dense vegetation, making it an ideal choice for trimming grass, weeds, and overgrown areas. The engine's lightweight design contributes to reduced fatigue during extended use, allowing operators to work comfortably for longer periods.

The trimmer features an adjustable curved shaft, which ensures versatility in handling different tasks while providing optimal balance and reduced vibration. This design allows users to easily maneuver around flower beds, rocks, and other obstacles, making trimming more efficient and enjoyable. The WET2242STD also incorporates a dual-line feed system, which automatically advances the cutting line as needed, ensuring consistent cutting performance without interruptions.

Durability is a key characteristic of the WET2242STD. Its high-quality construction is built to withstand the rigors of regular use, featuring components that are resistant to wear and tear. The trimmer is also equipped with a protective shield that enhances safety while providing protection against debris.

In terms of technology, the WET2242STD utilizes an easy-start system that simplifies the process of getting the unit running, reducing the time and effort required to start the engine. This feature is especially beneficial for those who may be new to using string trimmers, as it minimizes frustration and ensures a quick start-up with minimal fuss.

Another noteworthy aspect of the WET2242STD is its user-friendly design. The trimmer is equipped with an ergonomic handle that provides a comfortable grip and reduces strain on the hands during operation. This thoughtful design feature enhances user control and precision when navigating around tight spaces.

Overall, the Weed Eater WET2242STD is a reliable, high-performance string trimmer that combines an efficient engine with user-friendly features. Its lightweight design, adjustable shaft, and automatic line feed system make it an excellent addition to any lawn care toolkit. Whether you're a homeowner looking to maintain your yard or a professional landscaper, the WET2242STD delivers impressive results with every use.
Top Page Image Contents