Weed Eater WET2242STA manual To Level Mower Housing, To Replace Mower Blade Drive Belt See Fig

Page 19

SERVICE AND ADJUSTMENTS

TO LEVEL MOWER HOUSING

Adjust the mower while tractor is parked on level ground or driveway. Make sure tires are properly inflated (See “PRODUCT SPECIFICATIONS” section of this manual). If tires are over or underinflated, you will not properly adjust your mower.

SIDE-TO-SIDE ADJUSTMENT (See Figs. 14 and 15)

Raise mower to its highest position.

At the midpoint of both sides of mower, measure height from bottom edge of mower to ground. Distance “A” on both sides of mower should be the same or within 1/4" of each other.

If adjustment is necessary, make adjustment on one side of mower only.

To raise one side of mower, tighten lift link adjustment nut on that side.

To lower one side of mower, loosen lift link adjustment nut on that side.

NOTE: Each full turn of adjustment nut will change mower height about 1/8".

Recheck measurements after adjusting.

BOTTOM EDGE

 

BOTTOM EDGE

OF MOWER TO

 

OF MOWER TO

GROUND

 

GROUND

A

GROUND LINE

A

FIG. 14

SUSPENSION ARM

LIFT LINK

ADJUSTMENT NUT

FIG. 15

FRONT-TO-BACK ADJUSTMENT (See Figs. 16 and 17)

IMPORTANT: DECK MUST BE LEVEL SIDE-TO-SIDE. IF THE FOLLOWING FRONT-TO-BACK ADJUSTMENT IS NECESSARY, BE SURE TO ADJUST BOTH FRONT LINKS EQUALLY SO MOWER WILL STAY LEVEL SIDE-TO-SIDE.

To obtain the best cutting results, the mower housing should be adjusted so that the front is approximately 1/8" to 1/2" lower than the rear when the mower is in its high- est position.

Check adjustment on right side of tractor. Measure distance “D” directly in front and behind the mandrel at bottom edge of mower housing as shown.

Before making any necessary adjustments, check that both front links are equal in length.

If links are not equal in length, adjust one link to same length as other link.

To lower front of mower loosen nut “E” on both front links an equal number of turns.

When distance “D” is 1/8" to 1/2" lower at front than rear, tighten nuts “F” against trunnion on both front links.

To raise front of mower, loosen nut “F” from trunnion on both front links. Tighten nut “E” on both front links an equal number of turns. The two front links must remain equal in length.

When distance “D” is 1/8" to 1/2" lower at front than rear, tighten nut “F” against trunnion on both front links.

Recheck side-to-side adjustment.

MANDREL

“D”

“D”

FIG. 16

BOTH FRONT LINKS MUST BE EQUAL IN LENGTH

NUT “F”

NUT “E”

TRUNNION

FRONT LINKS

FIG. 17

TO REPLACE MOWER BLADE DRIVE BELT (See Fig. 18)

The mower blade drive belt may be replaced without tools. Park the tractor on level surface. Engage parking brake.

BELT REMOVAL -

Remove mower from tractor (See “TO REMOVE MOWER” in this section of this manual).

Work belt off both mandrel pulleys and idler pulleys.

Pull belt away from mower.

BELT INSTALLATION -

Install new belt in reverse order of removal.

Make sure belt is in all pulley grooves and inside all belt guides.

Install mower in reverse order of removal instruc- tions.

19

Image 19
Contents Model NO. WET2242STA Safety Rules Safety Rules Table of Contents Contents of Hardware Pack Before Removing Tractor from Skid AssemblyTools Required for Assembly To Remove Tractor from CartonInstall Seat See Fig HOW to SET UP Your TractorCheck Battery See Fig Check Brake System Check Tire PressureCheck Deck Levelness Check for Proper Position of ALL BeltsOperation Know Your Tractor HOW to USE Your Tractor Before Starting the Engine To Start Engine See Fig Mowing TipsBefore Each USE MaintenanceLubrication Chart General RecommendationsTractor Engine IN-LINE Fuel Filter See Fig CleaningMuffler Spark PlugsTo Install Mower See Fig Service and AdjustmentsTo Remove Mower See Fig Belt Removal To Level Mower HousingBelt Installation To Replace Mower Blade Drive Belt See FigTo Check Brake To Check and Adjust Brake See FigTo Adjust Brake To Replace Motion Drive Belt See FigTo Remove Wheel for Repairs See Fig Transaxle Gear Shift Lever NEUTRAL- Adjustment See FigTo Adjust Steering Wheel ALIGN- Ment Front Wheel TOE-IN/CAMBERInterlocks and Relays To Replace Headlight BulbTo Replace Fuse To Adjust Choke Control To Adjust Throttle Control CableTo Adjust Carburetor Engine OIL StorageOther Fuel SystemTroubleshooting Points OFF Tractor - Model Number WET2242STA SchematicElectrical KEY Part Description Chassis and Enclosures 219 17670508 Screw 5479J Plug Btn Blk Drive Shaft Asm Cross Tapered PMST/20 Steering Assembly Nut Hex Jam Toplock 1/2-20 Unf Engine Seat Assembly Wheels & Tires DecalsMower Lift Mower Deck Repair Parts Limited Warranty Policy Suggested Guide for Sighting Slopes for Safe Operation

WET2242STA specifications

The Weed Eater WET2242STA is a versatile and efficient string trimmer designed to handle a variety of lawn maintenance tasks with ease. Known for its powerful performance and user-friendly features, the WET2242STA has become a staple in many residential gardens and landscaping projects.

One of the standout features of the WET2242STA is its robust 22cc two-cycle engine, which provides ample power for tackling even the toughest overgrowth. This engine is engineered for optimal fuel efficiency, ensuring that users can work longer without the need for frequent refueling. With a dependable starting mechanism, the Weed Eater minimizes frustration, allowing users to get started on their tasks quickly.

The design of the WET2242STA includes a straight shaft, making it easier to reach under bushes and around obstacles. The longer reach is particularly advantageous for trimming tall grass and weeds in hard-to-access areas. Additionally, the dual-line bump head simplifies the process of loading new string, enabling users to spend more time working and less time dealing with equipment maintenance.

A significant technological feature of the WET2242STA is its anti-vibration system which enhances comfort during extended use. This system significantly reduces the hand fatigue typically associated with lawn care tasks, allowing users to enjoy prolonged periods of trimming without discomfort.

The trimmer also features an adjustable handle, providing users with customizable control and comfort as they work. Whether tackling small residential lawns or larger, more demanding tasks, the adjustable handle allows for a more personalized grip.

Safety is also a priority in the design of the WET2242STA. The trimmer incorporates several safety features, including a protective shield that helps keep debris at bay and a throttle lock that prevents accidental starting.

Overall, the Weed Eater WET2242STA combines power, comfort, and user-friendly design to create a reliable tool for lawn care enthusiasts. With its powerful engine, innovative features, and thoughtful design, it stands out as an excellent choice for anyone looking to maintain a well-groomed outdoor space. The WET2242STA is engineered to make lawn care simpler and more enjoyable, ensuring that users can achieve professional results with minimal effort.