Weed Eater WET17H42STA manual Tools Required for Assembly, To Remove Tractor from CAR- TON

Page 6

ASSEMBLY

Your new tractor has been assembled at the factory with exception of those parts left unassembled for shipping purposes. To ensure safe and proper operation of your tractor all parts and hardware you assemble must be tightened securely. Use the correct tools as necessary to insure proper tightness.

TOOLS REQUIRED FOR ASSEMBLY

A socket wrench set will make assembly easier. Standard wrench sizes are listed.

(1)

3/4" wrench

Pliers

(2)

7/16" wrenches

Tire pressure gauge

 

 

Utility knife

When right or left hand is mentioned in this manual, it means when you are in the operating position (seated behind the steering wheel).

TO REMOVE TRACTOR FROM CAR- TON

UNPACK CARTON

•Remove all accessible loose parts and parts cartons from carton.

•Cut along dotted lines on all four panels of carton. Remove end panels and lay side panels flat.

•Check for any additional loose parts or cartons and remove.

BEFORE REMOVING TRACTOR FROM SKID

ATTACH STEERING WHEEL (SEE FIG. 1)

ASSEMBLE EXTENSION SHAFT AND BOOT

•Slide extension shaft onto lower steering shaft. Align mounting holes in extension and lower shafts and install 1/4 hex bolt and locknut. Tighten securely.

IMPORTANT: TIGHTEN BOLT AND NUT SECURELY TO 10-12 FT. LBS TORQUE.

 

INSERT

 

1/2 LOCK WASHER

 

LARGE FLAT

 

WASHER

STEERING

 

WHEEL

 

 

STEERING

 

BOOT

 

TABS

ADAPTER

EXTENSION SHAFT

 

 

1/4 HEX BOLT

1/4 LOCKNUT

 

LOWER

 

STEERING

 

SHAFT

 

 

TAB

 

SLOTS

FIG. 1

•Place tabs of steering boot over tab slots in dash and push down to secure.

INSTALL STEERING WHEEL

•Position front wheels of the tractor so they are pointing straight forward.

•Remove steering wheel adapter from steering wheel and slide adapter onto steering shaft extension.

•Position steering wheel so cross bars are horizontal (left to right) and slide inside boot and onto adapter.

•Assemble large flat washer, 1/2 hex nut and tighten securely.

•Snap steering wheel insert into center of steering wheel.

•Remove protective materials from tractor hood and grill.

IMPORTANT: CHECK FOR AND REMOVE ANY STAPLES IN SKID THAT MAY PUNCTURE TIRES WHERE TRACTOR IS TO ROLL OFF SKID.

HOW TO SET UP YOUR TRACTOR

INSTALL SEAT (See Fig. 2)

Adjust seat before tightening adjustment bolt.

•Remove adjustment bolt, lock washer and flat washer securing seat to cardboard packing and set aside for assembly of seat to tractor.

•Pivot seat upward and remove from the cardboard pack- ing. Remove the cardboard packing and discard.

•Place seat on seat pan so head of shoulder bolt is positioned over large slotted hole in pan.

•Push down on seat to engage shoulder bolt in slot and pull seat towards rear of tractor.

•Pivot seat and pan forward and assemble adjust- ment bolt, lockwasher and flat washer loosely. Do not tighten

•Lower seat into operating position and sit on seat.

•Slide seat until a comfortable position is reached which allows you to press clutch/brake pedal all the way down.

6

Page 5 Page 7
Image 6
Page 5 Page 7
Contents Model NO. WET17H42STA General Operation Safety RulesIV. Service II. Slope OperationSafety Rules Table of Contents Key Unassembled PartsSteering Wheel Seat Slope SheetHOW to SET UP Your Tractor AssemblyTools Required for Assembly To Remove Tractor from CAR- TONCheck Battery See Fig Check for Proper Position of ALL Belts Check Tire PressureCheck Deck Levelness Check Brake SystemOperation Know Your Tractor HOW to USE Your Tractor To Operate on Hills Before Starting the EngineTo Operate Mower See Fig To Transport See FigsPurge Transmission ADD GasolineTo Start Engine See Fig Automatic Transmission Warm UPMowing Tips General Recommendations MaintenanceLubrication Chart Before Each USETractor Engine AIR Filter CleaningEngine Cooling Fins MufflerTo Level Mower Housing Service and AdjustmentsTo Install Mower See Fig To Remove Mower See FigBelt Installation To Replace Mower Blade Drive Belt See FigBelt Removal To Adjust Brake To Check and Adjust Brake See FigTransaxle Motion Control Lever Neutral Adjustment See Fig To Replace Motion Drive Belt See FigReplacing Battery See Figs Transmission REMOVAL/REPLACEMENTTo Adjust Steering Wheel ALIGN- Ment Front Wheel TOE-IN/CAMBERTo Replace Headlight Bulb To Adjust Throttle Control CableTo Adjust Carburetor Interlocks and RelaysFuel System StorageOther Engine OILTroubleshooting Points OFF Schematic Tractor - Model Number WET17H42STATractor - Model Number WET17H42STA Electrical KEY Part NO. NO. Description Tractor - Model Number WET17H42STA Chassis and Enclosures KEY Part Description Tractor - Model Number WET17H42STA Drive Repair Parts Tractor - Model Number WET17H42STA Steering Assembly KEY Part NO. NO. Description Tractor - Model Number WET17H42STA Engine Optional EquipmentTractor - Model Number WET17H42STA Seat Assembly Tractor - Model Number WET17H42STA Decals Wheels & TiresTractor - Model Number WET17H42STA Mower Lift 173288 Link FrontTractor - Model Number WET17H42STA Mower Deck 165892 Policy Suggested Guide for Sighting Slopes for Safe Operation Only Ride UP and Down Hill Not Across Hill Degrees MAXLimited Warranty

WET17H42STA specifications

The Weed Eater WET17H42STA is a robust and versatile lawn care solution designed for homeowners seeking an efficient and effective way to maintain their lawns. This riding mower packs a powerful punch with its reliable engine and innovative features, making lawn maintenance a breeze.

At the heart of the WET17H42STA is a strong 17 horsepower Briggs & Stratton engine. This engine offers impressive performance, delivering ample power to tackle tough grass and uneven terrain. The automatic transmission allows for seamless gear changes, ensuring that users can effortlessly navigate their lawns without worrying about shifting gears manually.

One of the standout features of the WET17H42STA is its 42-inch cutting deck. This wide deck enables users to cover more ground in less time, which is especially beneficial for larger yards. Furthermore, the cutting height can be easily adjusted, offering six different positions to suit various grass lengths and conditions. This adaptability ensures a clean and precise cut, promoting a healthy lawn throughout the growing season.

The design of the WET17H42STA prioritizes user comfort and ease of use. The mower is equipped with a plush, adjustable seat that provides comfort during extended mowing sessions. The steering wheel is ergonomically designed, allowing for a smooth and responsive driving experience. Additionally, the mower's compact size makes it easy to maneuver around obstacles such as trees, flower beds, and fencing.

Safety features are also a priority in the WET17H42STA. The mower includes a brake system that ensures it comes to a complete stop when the operator leaves the seat, reducing the risk of accidents. The engine also features an easy-to-access oil drain, making routine maintenance straightforward and hassle-free.

In terms of technology, the WET17H42STA boasts a simple starting system that minimizes the effort required to get started. The mower has been designed with durability in mind, incorporating high-quality materials that can withstand the rigors of regular lawn care.

Overall, the Weed Eater WET17H42STA stands out as an excellent choice for those looking for a reliable riding mower. Its combination of power, cutting efficiency, user comfort, and safety features makes it an ideal investment for achieving a well-manicured lawn with minimal effort. Whether you are a seasoned gardener or a novice, this mower will help you maintain your outdoor space with ease.
Top Page Image Contents