Weed Eater WET17H42STA To Replace Mower Blade Drive Belt See Fig, Belt Removal, Belt Installation

Page 20

SERVICE AND ADJUSTMENTS

SIDE-TO-SIDE ADJUSTMENT (See Figs. 15 and 16)

•Raise mower to its highest position.

•At the midpoint of both sides of mower, measure height from bottom edge of mower to ground. Distance “A” on both sides of mower should be the same or within 1/4" of each other.

•If adjustment is necessary, make adjustment on one side of mower only.

•To raise one side of mower, tighten lift link adjustment nut on that side.

•To lower one side of mower, loosen lift link adjustment nut on that side.

NOTE: Three full turns of adjustment nut will change mower height about 1/8".

•Recheck measurements after adjusting.

BOTTOM EDGE OF

 

BOTTOM EDGE

MOWER

 

OF MOWER

TO GROUND

 

TO GROUND

“A”

GROUND LINE

“A”

FIG. 15

SUSPENSION ARM

LIFT LINK ADJUSTMENT NUT

FIG. 16

FRONT-TO-BACK ADJUSTMENT (See Figs. 17 and 18)

IMPORTANT: DECK MUST BE LEVEL SIDE-TO-SIDE. IF THE FOLLOWING FRONT-TO-BACK ADJUSTMENT IS NECESSARY, BE SURE TO ADJUST BOTH FRONT LINKS EQUALLY SO MOWER WILL STAY LEVEL SIDE-TO-SIDE.

To obtain the best cutting results, the mower housing should be adjusted so that the front is approximately 1/8" to 1/2" lower than the rear when the mower is in its high- est position.

Check adjustment on right side of tractor. Measure distance “D” directly in front and behind the mandrel at bottom edge of mower housing as shown.

•Before making any necessary adjustments, check that both front links are equal in length.

•If links are not equal in length, adjust one link to same length as other link.

•To lower front of mower loosen nut “E” on both front links an equal number of turns.

•When distance “D” is 1/8" to 1/2" lower at front than rear, tighten nuts “F” against trunnion on both front links.

•To raise front of mower, loosen nut “F” from trunnion on both front links. Tighten nut “E” on both front links an equal number of turns. The two front links must remain equal in length.

•When distance “D” is 1/8" to 1/2" lower at front than rear, tighten nut “F” against trunnion on both front links.

•Recheck side-to-side adjustment.

MANDREL

"D"

"D"

FIG. 17

BOTH FRONT LINKS MUST BE EQUAL IN LENGTH

NUT "F"

NUT "E"

TRUNNION

FRONT LINKS

FIG. 18

TO REPLACE MOWER BLADE DRIVE BELT (See Fig. 19)

The mower blade drive belt may be replaced without tools. Park the tractor on level surface. Engage parking brake.

BELT REMOVAL -

•Remove mower from tractor (See “TO REMOVE MOWER” in this section of this manual).

•Work belt off both mandrel pulleys and idler pulleys.

•Pull belt away from mower.

BELT INSTALLATION -

•Install new belt in reverse order of removal.

•Make sure belt is in all pulley grooves and inside all belt guides.

•Install mower in reverse order of removal instruc- tions.

MANDREL PULLEY

IDLER PULLEYS

MANDREL

PULLEY

FIG. 19

20

Page 19 Page 21
Image 20
Page 19 Page 21
Contents Model NO. WET17H42STA Safety Rules IV. ServiceGeneral Operation II. Slope OperationSafety Rules Table of Contents Unassembled Parts Steering Wheel SeatKey Slope SheetAssembly Tools Required for AssemblyHOW to SET UP Your Tractor To Remove Tractor from CAR- TONCheck Battery See Fig Check Tire Pressure Check Deck LevelnessCheck for Proper Position of ALL Belts Check Brake SystemOperation Know Your Tractor HOW to USE Your Tractor Before Starting the Engine To Operate Mower See FigTo Operate on Hills To Transport See FigsADD Gasoline To Start Engine See FigPurge Transmission Automatic Transmission Warm UPMowing Tips Maintenance Lubrication ChartGeneral Recommendations Before Each USETractor Engine Cleaning Engine Cooling FinsAIR Filter MufflerService and Adjustments To Install Mower See FigTo Level Mower Housing To Remove Mower See FigBelt Removal Belt InstallationTo Replace Mower Blade Drive Belt See Fig To Check and Adjust Brake See Fig Transaxle Motion Control Lever Neutral Adjustment See FigTo Adjust Brake To Replace Motion Drive Belt See FigTransmission REMOVAL/REPLACEMENT To Adjust Steering Wheel ALIGN- MentReplacing Battery See Figs Front Wheel TOE-IN/CAMBERTo Adjust Throttle Control Cable To Adjust CarburetorTo Replace Headlight Bulb Interlocks and RelaysStorage OtherFuel System Engine OILTroubleshooting Points OFF Schematic Tractor - Model Number WET17H42STATractor - Model Number WET17H42STA Electrical KEY Part NO. NO. Description Tractor - Model Number WET17H42STA Chassis and Enclosures KEY Part Description Tractor - Model Number WET17H42STA Drive Repair Parts Tractor - Model Number WET17H42STA Steering Assembly KEY Part NO. NO. Description Tractor - Model Number WET17H42STA Engine Optional EquipmentTractor - Model Number WET17H42STA Seat Assembly Tractor - Model Number WET17H42STA Decals Wheels & TiresTractor - Model Number WET17H42STA Mower Lift 173288 Link FrontTractor - Model Number WET17H42STA Mower Deck 165892 Policy Suggested Guide for Sighting Slopes for Safe Operation Only Ride UP and Down Hill Not Across Hill Degrees MAXLimited Warranty

WET17H42STA specifications

The Weed Eater WET17H42STA is a robust and versatile lawn care solution designed for homeowners seeking an efficient and effective way to maintain their lawns. This riding mower packs a powerful punch with its reliable engine and innovative features, making lawn maintenance a breeze.

At the heart of the WET17H42STA is a strong 17 horsepower Briggs & Stratton engine. This engine offers impressive performance, delivering ample power to tackle tough grass and uneven terrain. The automatic transmission allows for seamless gear changes, ensuring that users can effortlessly navigate their lawns without worrying about shifting gears manually.

One of the standout features of the WET17H42STA is its 42-inch cutting deck. This wide deck enables users to cover more ground in less time, which is especially beneficial for larger yards. Furthermore, the cutting height can be easily adjusted, offering six different positions to suit various grass lengths and conditions. This adaptability ensures a clean and precise cut, promoting a healthy lawn throughout the growing season.

The design of the WET17H42STA prioritizes user comfort and ease of use. The mower is equipped with a plush, adjustable seat that provides comfort during extended mowing sessions. The steering wheel is ergonomically designed, allowing for a smooth and responsive driving experience. Additionally, the mower's compact size makes it easy to maneuver around obstacles such as trees, flower beds, and fencing.

Safety features are also a priority in the WET17H42STA. The mower includes a brake system that ensures it comes to a complete stop when the operator leaves the seat, reducing the risk of accidents. The engine also features an easy-to-access oil drain, making routine maintenance straightforward and hassle-free.

In terms of technology, the WET17H42STA boasts a simple starting system that minimizes the effort required to get started. The mower has been designed with durability in mind, incorporating high-quality materials that can withstand the rigors of regular lawn care.

Overall, the Weed Eater WET17H42STA stands out as an excellent choice for those looking for a reliable riding mower. Its combination of power, cutting efficiency, user comfort, and safety features makes it an ideal investment for achieving a well-manicured lawn with minimal effort. Whether you are a seasoned gardener or a novice, this mower will help you maintain your outdoor space with ease.
Top Page Image Contents