Before Starting Engine Fueling Engine | Weed Eater 530165291-01

SAfter using blowers and other equipment, CLEAN UP! Dispose of debris in trash re- ceptacles.

BEFORE STARTING ENGINE

WARNING: Be sure to read the fuel information in the safety rules before you be- gin. If you do not understand the safety rules, do not attempt to fuel your unit. Call 1-800-554-6723.

FUELING ENGINE

WARNING: Remove fuel cap slowly when refueling.

This engine is certified to operate on unleaded gasoline. Before operation, gasoline must be mixed with a good quality synthetic 2-cycle air-cooled engine oil designed to be mixed at a ratio of 40:1. Poulan/Weed Eater brand synthetic oil is recommended. Mix gasoline and oil at a ratio of 40:1. A 40:1 ratio is obtained by mixing 3.2 ounces (95 ml) of oil with 1 gallon (4 liters) of unleaded gasoline. DO NOT USE automotive oil or boat oil. These oils will cause engine damage. When mixing fuel, follow instructions printed on container. Once oil is added to gasoline, shake container momentarily to assure that the fuel is thoroughly mixed. Always read and follow the safety rules relating to fuel before fueling your unit.

IMPORTANT

Experience indicates that alcohol blended fuels (called gasohol or using ethanol or methanol) can attract moisture which leads to separation and formation of acids during storage. Acidic gas can damage the fuel system of an engine while in storage. To avoid engine problems, empty the fuel system before storage for 30 days or longer. Drain the gas tank, start the engine and let it run until the fuel lines and carburetor are empty. Use fresh fuel next season. Never use engine or carburetor cleaner products in the fuel tank or permanent damage may occur.

NOTE: Unit must be placed on its side when adding fuel (see illustration below).

TO STOP THE ENGINE

DTo stop the engine, move the throttle lever to the STOP position.

BEFORE STARTING THE ENGINE

WARNING: You MUST make sure the tubes are secure before using the unit.

DFuel engine. Move at least 10 feet (3 me- ters) away from the fueling site.

DHold the unit in the starting position as shown. Make sure the blower end is di- rected away from people, animals, glass, and solid objects.

STARTING POSITION

WARNING: When starting engine, hold the unit as illustrated. Do not set unit on any surface except a clean, hard area when starting engine or while engine is running. Debris such as gravel, sand, dust, grass, etc. could be picked up by the air intake and thrown out through the discharge opening, damaging the unit or property, or causing serious injury to by- standers or the operator.

STARTING A COLD ENGINE

1.Move throttle lever to the position.

2.Move choke lever to the FULL CHOKE position.

3.Slowly press the primer button 8 times.

Throttle Lever

Primer Button

Choke Lever

4.Pull starter rope sharply until engine at- tempts to run, but no more than 5 pulls (be- low 30_ F, 8 pulls).

NOTE: If engine attempts to start before the 5th pull, go to next step immediately.

5.Move the choke lever to the HALF CHOKE position.

6.Pull the starter rope sharply until the en- gine runs, but no more than 5 pulls (below 30_ F, 10 pulls).

7.After a 5 second warm--up, move the choke lever to the RUN position.

8.Allow the unit to run for 30 more seconds at the RUN position before moving the

throttle lever to position.

-- 5 --

530165291-01, B1750 LE specifications

The Weed Eater B1750 LE, model number 530165291-01, presents a powerful solution for tackling various outdoor weed control tasks. Designed for both professionals and avid gardeners, this string trimmer boasts an impressive array of features, ensuring efficient performance for maintaining lawns, gardens, and outdoor spaces.

At its core, the B1750 LE is powered by a reliable 17 cc, 2-cycle engine, delivering the capability to effectively trim through tough weeds and grass. This lightweight engine offers a perfect balance of power and portability, making it easy to maneuver around shrubs, flower beds, and tight corners in your yard. The innovative design of the engine ensures reduced emissions and improved fuel efficiency, thereby contributing to environmental sustainability.

One of the standout features of the B1750 LE is its Easy Start technology, which simplifies the starting process. With just a few simple pulls, users can ignite the engine with minimal effort, reducing frustrations often associated with traditional starting mechanisms. This technology is particularly beneficial for those who may struggle with more demanding equipment.

Equipped with a generous 16-inch cutting swath, the B1750 LE allows users to cover more ground in less time, cutting down on overall trimming time. The Tap 'n Go line advancement feature allows for quick and easy line feed, ensuring that the cutting line is always ready for use without the need for complicated adjustments. This functional design minimizes downtime when tackling large areas.

Durability is also a hallmark of the Weed Eater B1750 LE. The trimmer features a robust construction, with a reinforced cutting head designed to withstand heavy usage. Moreover, it is equipped with ergonomically designed handles, providing comfort during extended use and reducing hand fatigue. The shoulder strap included with the trimmer further enhances user comfort by distributing weight evenly across the body.

In terms of versatility, this string trimmer is ideal for a variety of tasks, from edging along sidewalks and driveways to clearing thick underbrush and overgrown grass. The optional attachments available for the B1750 ensure that users can expand its functionality to meet their specific gardening needs.

In summary, the Weed Eater B1750 LE, 530165291-01, is an effective and efficient string trimmer that combines power, ease of use, and durability. Its advanced features and technologies make it an excellent choice for anyone looking to maintain their yard efficiently and effectively. Whether you're a seasoned professional or a weekend warrior, the B1750 LE is designed to make lawn care tasks easier and more enjoyable.