Weed Eater WE20C, 96132006300, 438184 manual Troubleshooting, Problem Cause Correction

Page 15

TROUBLESHOOTING

PROBLEM

 

CAUSE

CORRECTION

Does not start

1.

Start button not depressed.

1.

Press start button and hold

 

 

 

 

down operator presence

 

 

 

 

control bar to handle.

 

2.

Extension cord not

2.

Reconnect extension cord

 

 

connected to power cord.

 

and use cord retainer to keep

 

 

 

 

the cord in place.

 

3.

Extension cord not

3.

Connect extension cord to a

 

 

connected to power source.

 

live and properly grounded

 

 

 

 

120V AC, 60 Hz receptacle.

 

4.

Circuit breaker has tripped.

4.

Wait 5 minutes for motor to

 

 

 

 

cool down. Push circuit

 

 

 

 

breaker to reset.

 

5.

Loose blade or broken

5.

Tighten blade bolt or

 

 

blade adapter.

 

replace blade adapter.

 

6.

Operator presence control

6.

Press start button and hold

 

 

bar in released position.

 

down operator presence

 

 

 

 

control bar to handle.

 

7.

Operator presence control

7.

Replace operator presence

 

 

bar defective.

 

control bar.

 

 

 

 

 

Loss of power

1.

Rear of lawn mower

1.

Raise cutting height.

 

 

housing or cutting blade

 

 

 

 

dragging in heavy grass.

 

 

 

2.

Cutting too much grass.

2.

Raise cutting height.

 

3.

Buildup of grass, leaves,

3.

Clean underside of mower

 

 

and trash under mower.

 

housing.

 

4.

Walking speed too fast.

4.

Cut at slower walking speed.

 

 

 

 

 

Poor cut –

1.

Worn, bent or loose blade.

1.

Replace blade. Tighten

uneven

 

 

 

blade bolt.

 

2.

Buildup of grass, leaves

2.

Clean underside of

 

 

and trash under mower.

 

mower housing.

 

 

 

 

 

Excessive

1.

Worn, bent or loose blade.

1.

Replace blade. Tighten

vibration

 

 

 

blade bolt.

 

 

 

 

 

Grass catcher

1.

Cutting height too low.

1.

Raise cutting height.

not filling

2.

Lift on blade worn off.

2.

Replace blade.

(If so equipped)

3.

Catcher not venting air.

3.

Clean grass catcher.

 

 

 

 

 

Hard to push

1.

Grass is too high or wheel

1.

Raise cutting height.

 

 

height is too low.

 

 

 

2.

Lawn mower housing or

2.

Raise lawn mower housing

 

 

or cutting blade dragging

 

one (1) setting higher.

 

 

in grass.

 

 

 

3.

Grass catcher too full.

3.

Empty grass catcher.

 

4.

Handle height position not

4.

Adjust handle height to suit.

 

 

right for you.

 

 

 

 

 

 

 

15

Image 15
Contents OPERATOR’S Manual Safety Rules Table of ContentsIII. Children General OperationII. Slope Operation Do notTo Remove Mower from Carton AssemblyHOW to SET UP Your Lawn Mower IV. General ServicePolarized Appliance Connections PRE-OPERATIONPRE-OPERATION Meets Cpsc Safety Requirements OperationKnow Your Lawn Mower Extension Cord Retainer HOW to USE Your Lawn MowerTo Start To StopTo Adjust Cutting Height To Attach Grass CatcherTo Empty Grass Catcher To Convert Mower Simple Steps to Remember When Converting Your Lawn MowerMulching Mowing Tips Mowing TipsLubrication MaintenanceGeneral Recommendations Before Each USEBlade Care CleaningLawn Mower TiresExtension Cord StorageOther HandleProblem Cause Correction TroubleshootingLimited Warranty