Weed Eater 178078, WE13T38D Cleaning, To Remove Mower See Fig, To Install Mower See Fig

Page 17

CUSTOMER RESPONSIBILITIES

CLEANING

•Clean engine, battery, seat, finish, etc. of all foreign matter.

•Keep finished surfaces and wheels free of all gasoline, oil, etc.

•Protect painted surfaces with automotive type wax.

We do not recommend using a garden hose to clean your tractor unless the electrical system, muffler, air filter and carburetor are covered to keep water out. Water in engine can result in a shortened engine life.

CAUTION: BEFORE PERFORMING ANY SERVICE OR ADJUSTMENTS:

•Depress clutch/brake pedal fully and set parking brake.

•Place gearshift lever in neutral (N) position.

•Place attachment clutch in “DISENGAGED” position.

•Turn ignition key “OFF” and remove key.

•Make sure the blades and all moving parts have completely stopped.

•Disconnect spark plug wire from spark plug and place wire where it cannot come in contact with plug.

TRACTOR

TO REMOVE MOWER (See Fig. 13)

Mower will be easier to remove from the right side of tractor.

•Place attachment clutch in “DISENGAGED” position.

•Move attachment lift lever forward to lower mower to its lowest position.

•Roll belt off engine pulley.

•Remove small retainer spring, and lift clutch spring off pulley bolt.

•Remove large retainer spring, slide collar off and push housing guide out of bracket.

•Disconnect anti-swaybar from chassis bracket by re- moving retainer spring.

•Disconnect suspension arms from rear deck brackets by removing retainer springs.

•Disconnect front links from deck by removing retainer springs.

•Raise lift lever to raise suspension arms. Slide mower out from under tractor.

IMPORTANT: IF AN ATTACHMENT OTHER THAN THE MOWER DECK IS TO BE MOUNTED ON THE TRAC- TOR, REMOVE THE FRONT LINKS AND HOOK THE CLUTCH SPRING INTO SQUARE HOLE IN FRAME.

TO INSTALL MOWER (See Fig. 13

•Raise attachment lift lever to its highest position.

•Slide mower under tractor with deflector shield to right side of tractor.

•Lower lift lever to its lowest position.

•Install mower in reverse order of removal instructions.

SUSPENSION ARMS

SQUARE HOLE

SMALL RETAINER SPRING

ENGINE PULLEY

 

CLUTCH SPRING

FRONT LINK

RETAINER SPRING

ANTI-SWAY BAR

RETAINER SPRINGS

 

(BOTH SIDES)

COLLAR

 

HOUSING GUIDE

LARGE RETAINER

 

SPRING

BRACKET

Fig. 13

17

Page 16 Page 18
Image 17
Page 16 Page 18
Contents Model NO. WE13T38D IV. Service Safety RulesGeneral Operation II. Slope OperationTable of Contents Customer Responsibilities Product SpecificationsKeys Unassembled PartsSteering Wheel Seat Tools Required for Assembly AssemblyTo Remove Tractor from Carton Before Removing Tractor from SkidInstall Seat See Fig HOW to SET UP Your TractorCheck Battery See Fig Check Deck Levelness Check Tire PressureCheck for Proper Position of ALL Belts Check Brake SystemOperation Know Your Tractor To USE Throttle Control see FIG HOW to USE Your TractorBefore Starting the Engine To Start Engine See Fig Mowing TipsCustomer Responsibilities Lubrication ChartGeneral Recommendations Before Each USETractor Engine To Remove Mower See Fig CleaningTo Install Mower See Fig To Replace Mower Blade Drive Belt See Fig Service and AdjustmentsTo Level Mower Housing Front Wheel TOE-IN/CAMBER To Adjust Steering Wheel AlignmentTo Replace Headlight Bulb Replacing Battery See FigsInterlocks and Relays To Replace FuseTo Adjust Carburetor To Remove Hood and Grill Assembly See FigEngine To Adjust Throttle Control Cable Other StorageFuel System Engine OILTroubleshooting Points OFF Tractor - Model Number WE13T38D SchematicElectrical KEY Part NO. NO.DESCRIPTION Chassis KEY Part Description Drive Transaxle Steering 140044X428 Engine 170864 Control Th/ch Flag Seat Wheels & Tires DecalsMower Lift 159460 Wire Asm Inner/Sprg w/plunger Mower Deck Repair Parts Service Notes Service Notes Service Notes Limited Warranty Policy Sighting Guide Suggested Guide for Sighting Slopes for Safe Operation
Top Page Image Contents