Weed Eater WE13T38D Tools Required for Assembly, To Remove Tractor from Carton, Unpack Carton

Page 6

ASSEMBLY

Your new tractor has been assembled at the factory with exception of those parts left unassembled for shipping purposes. To ensure safe and proper operation of your tractor all parts and hardware you assemble must be tightened securely. Use the correct tools as necessary to insure proper tightness.

TOOLS REQUIRED FOR ASSEMBLY

A socket wrench set will make assembly easier. Standard wrench sizes are listed.

(2)

1/2" wrenches

Pliers

(1)

9/16" wrench

Tire pressure gauge

 

 

Utility knife

When right or left hand is mentioned in this manual, it means when you are in the operating position (seated behind the steering wheel).

TO REMOVE TRACTOR FROM CARTON

UNPACK CARTON

•Remove all accessible loose parts and parts cartons from carton.

•Cut, from top to bottom, along lines on all four corners of carton, and lay panels flat.

•Check for any additional loose parts or cartons and remove.

BEFORE REMOVING TRACTOR FROM SKID

ATTACH STEERING WHEEL (See Fig. 1)

ASSEMBLE EXTENSION SHAFT AND BOOT

•Slide extension shaft onto lower steering shaft. Align mounting holes in extension and lower shafts and install 5/16 hex bolt and locknut. Tighten securely.

•Place tabs of steering boot over tab slots in dash and push down to secure.

INSTALL STEERING WHEEL

•Position front wheels of the tractor so they are pointing straight forward.

•Remove steering wheel adapter from steering wheel and slide adapter onto steering shaft extension.

•Position steering wheel so cross bars are horizontal (left to right) and slide inside boot and onto adapter.

•Assemble large flat washer, 3/8 lock washer, 3/8 hex bolt and tighten securely.

•Snap steering wheel insert into center of steering wheel.

•Remove protective materials from tractor hood and grill.

IMPORTANT: CHECK FOR AND REMOVE ANY STAPLES IN SKID THAT MAY PUNCTURE TIRES WHERE TRACTOR IS TO ROLL OFF SKID.

 

INSERT

 

3/8 HEX BOLT

 

3/8 LOCK WASHER

 

LARGE FLAT

 

WASHER

STEERING

 

WHEEL

 

 

STEERING

 

BOOT

 

TABS

ADAPTER

 

 

EXTENSION SHAFT

 

5/16 HEX BOLT

5/16 LOCKNUT

 

LOWER

 

STEERING

TAB

SHAFT

 

SLOTS

FIG. 1

6

Page 5 Page 7
Image 6
Page 5 Page 7
Contents Model NO. WE13T38D General Operation Safety RulesIV. Service II. Slope Operation Table of Contents Product Specifications Customer ResponsibilitiesUnassembled Parts Steering Wheel SeatKeys To Remove Tractor from Carton AssemblyTools Required for Assembly Before Removing Tractor from SkidHOW to SET UP Your Tractor Check Battery See FigInstall Seat See Fig Check for Proper Position of ALL Belts Check Tire PressureCheck Deck Levelness Check Brake SystemOperation Know Your Tractor HOW to USE Your Tractor To USE Throttle Control see FIGBefore Starting the Engine Mowing Tips To Start Engine See FigGeneral Recommendations Lubrication ChartCustomer Responsibilities Before Each USETractor Engine Cleaning To Install Mower See FigTo Remove Mower See Fig Service and Adjustments To Level Mower HousingTo Replace Mower Blade Drive Belt See Fig To Adjust Steering Wheel Alignment Front Wheel TOE-IN/CAMBERInterlocks and Relays Replacing Battery See FigsTo Replace Headlight Bulb To Replace FuseTo Remove Hood and Grill Assembly See Fig Engine To Adjust Throttle Control CableTo Adjust Carburetor Fuel System StorageOther Engine OILTroubleshooting Points OFF Schematic Tractor - Model Number WE13T38DElectrical KEY Part NO. NO.DESCRIPTION Chassis KEY Part Description Drive Transaxle Steering 140044X428 Engine 170864 Control Th/ch Flag Seat Decals Wheels & TiresMower Lift 159460 Wire Asm Inner/Sprg w/plunger Mower Deck Repair Parts Service Notes Service Notes Service Notes Limited Warranty Policy Suggested Guide for Sighting Slopes for Safe Operation Sighting Guide
Top Page Image Contents