Weed Eater WET1338B manual HOW to SET UP Your Tractor, Install Seat See Fig, Check Battery See Fig

Page 7

ASSEMBLY

HOW TO SET UP YOUR TRACTOR

INSTALL SEAT (See Fig. 2)

Adjust seat before tightening adjustment bolt.

•Remove adjustment bolt, lock washer and flat washer securing seat to cardboard packing and set aside for assembly of seat to tractor.

•Pivot seat upward and remove from the cardboard pack- ing. Remove the cardboard packing and discard.

•Place seat on seat pan so head of shoulder bolt is positioned over large slotted hole in pan.

•Push down on seat to engage shoulder bolt in slot and pull seat towards rear of tractor.

•Pivot seat and pan forward and assemble adjust- ment bolt, lockwasher and flat washer loosely. Do not tighten

•Lower seat into operating position and sit on seat.

•Slide seat until a comfortable position is reached which allows you to press clutch/brake pedal all the way down.

•Get off seat without moving its adjusted position.

•Raise seat and tighten adjustment bolt securely.

SEAT

SEAT PAN

SHOULDER

BOLT

02466

FLAT WASHER

LOCK WASHER

02465

ADJUSTMENT

BOLT

FIG. 2

CHECK BATTERY (See Fig. 3)

•Lift seat pan to raised position.

•If this battery is put into service after month and year indicated on label (label located between terminals) charge battery for minimum of one hour at 6-10 amps. (See “BATTERY” in the Maintenance section of this manual for charging instructions).

SEAT PAN

LABEL

FIG. 3

NOTE: You may now roll or drive your tractor off the skid. Follow the appropriate instruction below to remove the tractor from the skid.

TO ROLL TRACTOR OFF SKID (See Operation section for location and function of controls)

•Press lift lever plunger and raise attachment lift lever to its highest position.

•Release parking brake by depressing clutch/brake pedal.

•Place gearshift lever in neutral (N) position.

•Roll tractor forward off skid.

•Remove banding holding deflector shield up against tractor.

TO DRIVE TRACTOR OFF SKID (See Op- eration section for location and function of controls)

WARNING: Before starting, read, understand and follow all instructions in the Operation section of this manual. Be sure tractor is in a well-ventilated area. Be sure the area in front of tractor is clear of other people and objects.

•Be sure all the above assembly steps have been com- pleted.

•Check engine oil level and fill fuel tank with gasoline.

•Sit on seat in operating position, depress clutch/brake pedal and set the parking brake.

•Place gear shift lever in neutral (N) position.

•Press lift lever plunger and raise attachment lift lever to its highest position.

•Start the engine.After engine has started, move throttle control to idle position.

•Depress clutch/brake pedal into full "BRAKE" position and hold. Move gearshift lever to 1st gear.

•Slowly release clutch/brake pedal and slowly drive tractor off skid.

•Apply brake to stop tractor, set parking brake and place gearshift lever in neutral position.

•Turn ignition key to "OFF" position.

Continue with the instructions that follow.

7

Page 6 Page 8
Image 7
Page 6 Page 8
Contents Model NO. WET1338B II. Slope Operation Safety RulesIV. Service General OperationSafety Rules Table of Contents Steering Wheel Seat Unassembled PartsBefore Removing Tractor from Skid AssemblyTools Required for Assembly To Remove Tractor from CartonInstall Seat See Fig HOW to SET UP Your TractorCheck Battery See Fig Check Brake System Check Tire PressureCheck Deck Levelness Check for Proper Position of ALL BeltsOperation Know Your Tractor HOW to USE Your Tractor Check Engine OIL Level Before Starting the EngineTo Operate on Hills To Transport Towing Carts and Other ATTACH- MentsTo Start Engine See Fig Mowing TipsBefore Each USE MaintenanceLubrication Chart General RecommendationsOperator Presence System TractorBrake Operation TiresTransaxle Cooling BatteryEngine BeltsEngine Cooling Fins See Fig Clean AIR ScreenAIR Filter See Fig IN-LINE Fuel Filter See Fig CleaningMuffler Spark PlugsTo Install Mower See Fig Service and AdjustmentsTo Remove Mower See Fig Belt Removal To Level Mower HousingBelt Installation To Replace Mower Blade Drive Belt See FigFront Wheel TOE-IN/CAMBER To Check and Adjust Brake See FigTo Adjust Steering Wheel Align Ment To Replace Motion Drive Belt See FigTo Attach Jumper Cables To Start Engine with a Weak Battery See FigReplacing Battery See Figs To Remove Wheel for Repairs See FigTo Replace Fuse To Adjust CarburetorTo Replace Headlight Bulb Interlocks and RelaysEngine OIL StorageOther Fuel SystemTroubleshooting Points OFF Tractor - Model Number WET1338B SchematicElectrical KEY Part Description Chassis Repair Parts Drive Transaxle Steering Repair Parts Engine 170864 Control Th/ch Flag Seat Wheels & Tires DecalsMower Lift Repair Parts Mower Deck CAB Service Notes Limited Warranty Policy Only Ride UP and Down Hill Not Across Hill Degrees MAX Suggested Guide for Sighting Slopes for Safe OperationWeedeater

WET1338B specifications

The Weed Eater WET1338B is a powerful and efficient string trimmer designed for homeowners and professional landscapers alike. This robust tool is engineered to tackle a variety of cutting tasks, making it a versatile addition to any lawn care arsenal.

One of the standout features of the WET1338B is its 38cc two-cycle engine, which delivers impressive performance and reliability. This engine offers users the power needed to cut through thick grass, weeds, and even light brush without sacrificing efficiency. Its lightweight design ensures that users can maneuver it easily around their yards, reducing fatigue during extended use.

In terms of technology, the Weed Eater WET1338B is equipped with a 17-inch cutting width, allowing for a wide swath of grass to be trimmed with each pass. This feature significantly cuts down on the time needed to complete landscaping tasks. The dual-line trimmer head provides a professional finish while allowing for easy line replacement. The automatic line advancement system ensures that the cutting line is managed effectively, so users can focus on the job without worrying about running out of line mid-task.

Comfort and usability are at the forefront of the WET1338B’s design. The trimmer includes an adjustable handle that provides optimal control and comfort. The cushioned grip reduces vibrations during use, enhancing the overall user experience. The lightweight build of the trimmer also minimizes strain, making it suitable for users of varying physical abilities.

Moreover, the WET1338B is crafted with durability in mind. Its rugged construction is designed to withstand the rigors of regular use, ensuring that it remains a reliable tool for years to come. The fuel-efficient engine allows users to work longer without frequent refueling, adding to its practicality.

Safety features are also an essential aspect of the Weed Eater WET1338B. The inclusion of a protective guard enhances user safety, preventing debris from being thrown towards the operator during use.

Overall, the Weed Eater WET1338B stands out as a feature-rich, user-friendly string trimmer that effectively meets the demands of lawn care professionals and enthusiastic homeowners. Its combination of power, durability, and ease of use makes it a valuable investment for anyone looking to maintain their outdoor space with minimal effort.
Top Page Image Contents