Weed Eater 195013 Service and Adjustments, To Remove Mower See Fig, To Install Mower See Fig

Page 19

SERVICE AND ADJUSTMENTS

WARNING: TO AVOID SERIOUS INJURY, BEFORE PERFORMING ANY SERVICE OR ADJUST- MENTS:

Depress clutch/brake pedal fully and set parking brake.

Place gearshift lever in neutral (N) position.

Place attachment clutch in “DISENGAGED” position.

Turn ignition key to “STOP” and remove key.

Make sure the blades and all moving parts have completely stopped.

Disconnect spark plug wire from spark plug and place wire where it cannot come in contact with plug.

TRACTOR

TO REMOVE MOWER (See Fig. 13)

Mower will be easier to remove from the right side of trac- tor.

Place attachment clutch in “DISENGAGED” position.

Move attachment lift lever forward to lower mower to its lowest position.

Roll belt off engine pulley.

Remove small retainer spring, and remove clutch spring off pulley bolt.

Remove large retainer spring, slide collar off and push housing guide out of bracket.

Disconnect anti-swaybar from chassis bracket by re- moving retainer spring.

Disconnect suspension arms from rear deck brackets by removing retainer springs.

Disconnect front links from deck by removing retainer springs.

Raise lift lever to raise suspension arms. Slide mower out from under tractor.

IMPORTANT: IF AN ATTACHMENT OTHER THAN THE MOWER DECK IS TO BE MOUNTED ON THE TRACTOR, REMOVE THE FRONTLINKSANDHOOKTHECLUTCHSPRINGINTOSQUARE HOLE IN FRAME.

TO INSTALL MOWER (See Fig. 13)

Raise attachment lift lever to its highest position.

Slide mower under tractor with deflector shield to right side of tractor.

Lower lift lever to its lowest position.

Connect front links to mower deck and secure with retainer springs..

Connect suspension arms to rear deck brackets and secure with retainer springs.

Connect anti-swaybar to chassis bracket and secure with retainer spring.

Push clutch cable housing guide into bracket, slide col- lar onto guide and secure with large retainer spring.

Place flat washer and clutch spring on idler pulley bolt and secure with small retainer spring.

Install belt onto engine pulley.

 

SMALL

 

 

RETAINER

 

 

SPRING

 

FLAT WASHER

SUSPENSION

 

 

 

CLUTCH SPRING

ARMS

SQUARE HOLE

 

 

 

 

 

ENGINE PULLEY

RETAINER SPRING

 

FRONT LINK

ANTI-SWAY BAR

 

RETAINER SPRINGS

COLLAR

 

(BOTH SIDES)

 

 

HOUSING GUIDE

 

 

LARGE RETAINER

02695

 

SPRING

CLUTCH SPRING

DEFLECTOR SHIELD

 

 

BRACKET

 

 

FIG. 13

19

Image 19
Contents Always Wear EYE Protection During Operation WE13538LTII. Slope Operation Safety RulesSafe Operation Practices for Ride-On Mowers General OperationIV. Towing ServiceGeneral Service III. ChildrenTable of Contents Contents of Hardware Pack Before Removing Tractor from Skid AssemblyTools Required for Assembly To Remove Tractor from CartonCheck Battery See Fig Check Brake System Check Tire PressureCheck Deck Levelness Check for Proper Position of ALL BeltsOperation Know Your Tractor HOW to USE Your Tractor To Transport Reverse Operation System ROSTo Operate Mower See Fig To Operate on HillsTo Start Engine See Fig Before Starting the EngineCheck Engine OIL Level ADD GasolineMowing Tips Before Each USE MaintenanceLubrication Chart General RecommendationsBlade Removal See Fig TractorTo Sharpen Blade See Fig Transaxle Cooling BatteryEngine BeltsMuffler CleaningClean AIR Screen AIR FilterTo Install Mower See Fig Service and AdjustmentsTo Remove Mower See Fig Belt Removal To Level Mower HousingBelt Installation To Replace Mower Blade Drive Belt See FigTo Check Brake To Check and Adjust Brake See FigTo Adjust Brake To Replace Motion Drive Belt See FigFront Wheel TOE-IN/CAMBER Transaxle Gear Shift Lever NEUTRAL- Adjustment See FigTo Adjust Steering Wheel ALIGN- Ment To Start Engine with a Weak Battery See FigTo Replace Headlight Bulb To Adjust Throttle Control CableTo Adjust Choke Control To Adjust CarburetorEngine OIL StorageOther Fuel SystemProblem Cause Correction Troubleshooting PointsEngine dies when Limited Warranty Policy Only Ride UP and Down Hill Not Across Hill Degrees MAX Suggested Guide for Sighting Slopes for Safe OperationParts and Service

195013, WE13538LT specifications

The Weed Eater WE13538LT is a standout product in the landscaping and gardening industry, specifically designed for homeowners looking to maintain their lawns and gardens with ease and efficiency. This versatile string trimmer boasts a lightweight design coupled with powerful performance, making it an essential tool for any outdoor enthusiast.

One of the key features of the WE13538LT is its 38cc engine, which delivers ample power for trimming, edging, and clearing grass and weeds. This robust engine ensures that users can tackle tougher jobs without worrying about overheating or sacrificing performance. The 2-cycle gas-powered engine is designed for reliable operation, providing the perfect balance of power and weight. Its fuel-efficient design means that users can work longer without frequent refueling, making it ideal for large areas.

The trimmer's 17-inch cutting width is another notable feature, allowing for a wider swath with each pass. This reduces the amount of time spent trimming, making the overall gardening experience more efficient. The innovative bump head design makes it easy to reload the line, simply tapping the head on the ground automatically feeds more line to ensure uninterrupted trimming.

The WE13538LT is equipped with an ergonomic handle that enhances comfort during use. The adjustable handle allows users to customize their grip for optimal control and reduced fatigue, which is particularly important during extended periods of use. The lightweight design further contributes to user comfort, allowing for easy maneuverability without straining the arms or back.

Another significant feature is the inclusion of a straight shaft. This design not only provides improved reach, allowing users to access hard-to-reach areas but also enhances the tool's balance. The straight shaft is particularly advantageous when trimming along fences, walls, or flower beds, as it allows for precise cutting.

Safety is also a priority with the Weed Eater WE13538LT. It includes features like a protective shield that helps prevent debris from flying toward the operator, ensuring a safer working environment. Furthermore, the tool’s design incorporates low vibration technology, which minimizes user fatigue and enhances comfort during use.

In summary, the Weed Eater WE13538LT is a powerful and versatile string trimmer designed to meet the needs of homeowners. With its efficient 38cc engine, wide cutting width, ergonomic design, and safety features, it is an excellent choice for those looking to maintain a beautiful and pristine landscape effortlessly.