Weed Eater WE13538LT, 195013 manual Tools Required for Assembly, To Remove Tractor from Carton

Page 6

ASSEMBLY

Your new tractor has been assembled at the factory with exception of those parts left unassembled for shipping purposes. To ensure safe and proper operation of your tractor all parts and hardware you assemble must be tightened securely. Use the correct tools as necessary to insure proper tightness.

TOOLS REQUIRED FOR ASSEMBLY

A socket wrench set will make assembly easier. Standard wrench sizes are listed.

(1) 1/2" wrench

Utility knife

(1) 3/4" wrench

Tire pressure gauge

Pliers

 

When right or left hand is mentioned in this manual, it means when you are in the operating position (seated behind the steering wheel).

TO REMOVE TRACTOR FROM CARTON

UNPACK CARTON

•Remove all accessible loose parts and parts cartons from carton.

•Cut along dotted lines on all four panels of carton. Remove end panels and lay side panels flat.

•Check for any additional loose parts or cartons and remove.

BEFORE REMOVING TRACTOR FROM SKID

ATTACH STEERING WHEEL (See Fig. 1)

ASSEMBLE EXTENSION SHAFT AND BOOT

•Slide extension shaft onto lower steering shaft.

•Place tabs of steering boot over tab slots in dash and push down to secure.

INSTALL STEERING WHEEL

•Position front wheels of the tractor so they are pointing straight forward.

•Remove steering wheel adapter from steering wheel and slide adapter onto steering shaft extension.

•Position steering wheel so cross bars are horizontal (left to right) and slide inside boot and onto adapter.

•Assemble large flat washer, 5/16 lock washer, 5/16 hex bolt and tighten securely.

•Snap steering wheel insert into center of steering wheel.

•Remove protective materials from tractor hood and grill.

IMPORTANT: CHECK FOR AND REMOVE ANY STAPLES IN SKID THAT MAY PUNCTURE TIRES WHERE TRACTOR IS TO ROLL OFF SKID.

INSERT

5/16 HEX BOLT

5/16 LOCK WASHER

LARGE FLAT

WASHER

STEERING

WHEELSTEERING BOOT

TABS

ADAPTER

EXTENSION

SHAFT

LOWER

STEERING

SHAFT

TAB

SLOTS

FIG. 1

INSTALL SEAT (See Fig. 2)

Adjust seat before tightening adjustment bolt.

•Remove adjustment bolt, lock washer and flat washer securing seat to cardboard packing and set aside for assembly of seat to tractor.

•Pivot seat upward and remove from the cardboard pack- ing. Remove the cardboard packing and discard.

•Place seat on seat pan so head of shoulder bolt is positioned over large slotted hole in pan.

•Push down on seat to engage shoulder bolt in slot and pull seat towards rear of tractor.

•Pivot seat and pan forward and assemble adjust- ment bolt, lockwasher and flat washer loosely. Do not tighten

•Lower seat into operating position and sit on seat.

•Slide seat until a comfortable position is reached which allows you to press clutch/brake pedal all the way down.

•Get off seat without moving its adjusted position.

•Raise seat and tighten adjustment bolt securely.

6

Page 5 Page 7
Image 6
Page 5 Page 7
Contents WE13538LT Always Wear EYE Protection During OperationGeneral Operation Safety RulesSafe Operation Practices for Ride-On Mowers II. Slope OperationIII. Children ServiceGeneral Service IV. TowingTable of Contents Contents of Hardware Pack To Remove Tractor from Carton AssemblyTools Required for Assembly Before Removing Tractor from SkidCheck Battery See Fig Check for Proper Position of ALL Belts Check Tire PressureCheck Deck Levelness Check Brake SystemOperation Know Your Tractor HOW to USE Your Tractor To Operate on Hills Reverse Operation System ROSTo Operate Mower See Fig To TransportADD Gasoline Before Starting the EngineCheck Engine OIL Level To Start Engine See FigMowing Tips General Recommendations MaintenanceLubrication Chart Before Each USETractor Blade Removal See FigTo Sharpen Blade See Fig Belts BatteryEngine Transaxle CoolingAIR Filter CleaningClean AIR Screen MufflerService and Adjustments To Install Mower See FigTo Remove Mower See Fig To Replace Mower Blade Drive Belt See Fig To Level Mower HousingBelt Installation Belt RemovalTo Replace Motion Drive Belt See Fig To Check and Adjust Brake See FigTo Adjust Brake To Check BrakeTo Start Engine with a Weak Battery See Fig Transaxle Gear Shift Lever NEUTRAL- Adjustment See FigTo Adjust Steering Wheel ALIGN- Ment Front Wheel TOE-IN/CAMBERTo Adjust Carburetor To Adjust Throttle Control CableTo Adjust Choke Control To Replace Headlight BulbFuel System StorageOther Engine OILTroubleshooting Points Problem Cause CorrectionEngine dies when Limited Warranty Policy Suggested Guide for Sighting Slopes for Safe Operation Only Ride UP and Down Hill Not Across Hill Degrees MAXParts and Service

195013, WE13538LT specifications

The Weed Eater WE13538LT is a standout product in the landscaping and gardening industry, specifically designed for homeowners looking to maintain their lawns and gardens with ease and efficiency. This versatile string trimmer boasts a lightweight design coupled with powerful performance, making it an essential tool for any outdoor enthusiast.

One of the key features of the WE13538LT is its 38cc engine, which delivers ample power for trimming, edging, and clearing grass and weeds. This robust engine ensures that users can tackle tougher jobs without worrying about overheating or sacrificing performance. The 2-cycle gas-powered engine is designed for reliable operation, providing the perfect balance of power and weight. Its fuel-efficient design means that users can work longer without frequent refueling, making it ideal for large areas.

The trimmer's 17-inch cutting width is another notable feature, allowing for a wider swath with each pass. This reduces the amount of time spent trimming, making the overall gardening experience more efficient. The innovative bump head design makes it easy to reload the line, simply tapping the head on the ground automatically feeds more line to ensure uninterrupted trimming.

The WE13538LT is equipped with an ergonomic handle that enhances comfort during use. The adjustable handle allows users to customize their grip for optimal control and reduced fatigue, which is particularly important during extended periods of use. The lightweight design further contributes to user comfort, allowing for easy maneuverability without straining the arms or back.

Another significant feature is the inclusion of a straight shaft. This design not only provides improved reach, allowing users to access hard-to-reach areas but also enhances the tool's balance. The straight shaft is particularly advantageous when trimming along fences, walls, or flower beds, as it allows for precise cutting.

Safety is also a priority with the Weed Eater WE13538LT. It includes features like a protective shield that helps prevent debris from flying toward the operator, ensuring a safer working environment. Furthermore, the tool’s design incorporates low vibration technology, which minimizes user fatigue and enhances comfort during use.

In summary, the Weed Eater WE13538LT is a powerful and versatile string trimmer designed to meet the needs of homeowners. With its efficient 38cc engine, wide cutting width, ergonomic design, and safety features, it is an excellent choice for those looking to maintain a beautiful and pristine landscape effortlessly.
Top Page Image Contents