Weed Eater WET1742STB To Start Engine with a Weak Battery See Fig, Replacing Battery See Figs

Page 22

SERVICE AND ADJUSTMENTS

TO START ENGINE WITH A WEAK BATTERY (See Fig. 23)

WARNING: Lead-acid batteries gen- erate explosive gases. Keep sparks, flame and smoking materials away from batteries. Always wear eye protection when around batteries.

If your battery is too weak to start the engine, it should be recharged. (See "BATTERY" in the Maintenance section of this manual).

If “jumper cables” are used for emergency starting, follow this procedure:

IMPORTANT: YOUR TRACTOR IS EQUIPPED WITH A 12 VOLT SYSTEM. THE OTHER VEHICLE MUST ALSO BE A 12 VOLT SYSTEM. DO NOT USE YOUR TRACTOR BATTERY TO START OTHER VEHICLES.

TO ATTACH JUMPER CABLES -

Connect one end of the RED cable to the POSITIVE

(+)terminal of each battery(A-B), taking care not to short against tractor chassis.

Connect one end of the BLACK cable to the NEGATIVE (-) terminal (C) of fully charged battery.

Connect the other end of the BLACK cable (D) to good chassis ground, away from fuel tank and battery.

TO REMOVE CABLES, REVERSE ORDER -

BLACK cable first from chassis and then from the fully charged battery.

RED cable last from both batteries.

 

02614

WEAK OR DEAD

FULLY CHARGED

BATTERY

BATTERY

FIG. 23

REPLACING BATTERY (See Figs. 24 and 25)

WARNING: Do not short battery ter- minals by allowing a wrench or any other object to contact both terminals at the same time. Before connect- ing battery, remove metal brace- lets, wristwatch bands, rings, etc.

Positive terminal must be connected first to prevent sparking from accidental grounding.

Lift seat pan to raised position.

Disconnect BLACK battery cable first then RED battery cable and carefully remove battery from tractor.

Install new battery with terminals in same position as old battery.

First connect RED battery cable to positive (+) terminal with hex bolt and keps nut as shown. Tighten securely. Slide terminal cover over terminal.

Connect BLACK grounding cable to negative (-) ter- minal with remaining hex bolt and keps nut. Tighten securely.

SEAT PAN

02602

 

 

FIG. 24

TERMINAL

KEPS NUT

COVER

 

HEX

 

 

 

 

BOLT

02603

 

 

POSITIVE (RED) CABLE

NEGATIVE (BLACK) CABLE

FIG. 25

22

Image 22
Contents Model NO. WET1742STB Safety Rules Safety Rules Table of Contents Contents of Hardware Pack To Remove Tractor from Carton AssemblyTools Required for Assembly Before Removing Tractor from SkidInstall Seat See Fig Check Battery See FigCheck for Proper Position of ALL Belts Check Tire PressureCheck Deck Levelness Check Brake SystemOperation Know Your Tractor HOW to USE Your Tractor Before Starting the Engine Mowing Tips To Start Engine See FigGeneral Recommendations MaintenanceLubrication Chart Before Each USETractor Engine Spark Plugs CleaningMuffler IN-LINE Fuel Filter See FigTo Install Mower See Fig Service and AdjustmentsTo Remove Mower See Fig To Replace Mower Blade Drive Belt See Fig To Level Mower HousingBelt Installation Belt RemovalTo Replace Motion Drive Belt See Fig To Check and Adjust Brake See FigTo Adjust Brake To Check BrakeFront Wheel TOE-IN/CAMBER To Adjust Steering Wheel ALIGN- MentTransaxle Gear Shift Lever NEUTRAL- Adjustment See Fig To Remove Wheel for Repairs See FigTo Attach Jumper Cables To Start Engine with a Weak Battery See FigReplacing Battery See Figs To Remove CABLES, Reverse OrderTo Adjust Carburetor To Adjust Throttle Control CableTo Adjust Choke Control To Replace Headlight BulbFuel System StorageOther Engine OILTroubleshooting Points With attachment clutch Limited Warranty Policy Suggested Guide for Sighting Slopes for Safe Operation Only Ride UP and Down Hill Not Across Hill Degrees MAX

WET1742STB specifications

The Weed Eater WET1742STB is a versatile and efficient tool designed for homeowners and landscaping professionals alike. This gas-powered trimmer offers exceptional performance, making it an ideal choice for tackling tough overgrowth and maintaining a neat lawn.

One of the standout features of the WET1742STB is its powerful 17cc engine. This robust engine delivers reliable power, ensuring that users can easily handle various types of vegetation, from light grass to thicker weeds. The trimmer's speed is complemented by a straight shaft design, which allows for greater reach and maneuverability, making it easier to trim in hard-to-reach areas.

A key technology incorporated into this model is the dual line feed system. This feature enables the user to efficiently release more cutting line as needed, allowing for a wider cutting swath with each pass. This translates to reduced trimming time and enhanced productivity. The auto-feed spool ensures that the cutting line is replenished automatically, minimizing interruptions during operation.

Comfort and usability are also central to the design of the WET1742STB. It is equipped with a soft grip handle that reduces vibrations, enhancing user comfort during extended use. The lightweight design further adds to its ease of handling, allowing for extended periods of operation without causing undue fatigue. Additionally, the trimmer features an ergonomic throttle control that allows for precise speed adjustments.

One of the notable safety features of the WET1742STB is its protective guard, which shields the user from debris while trimming. This is especially important when tackling unruly growth, as it promotes safer operation without compromising efficiency.

Maintenance is simplified with the WET1742STB, thanks to its easy-access air filter and spark plug. This design feature ensures that users can quickly perform routine maintenance tasks, helping to extend the life of the trimmer and maintain peak performance.

In summary, the Weed Eater WET1742STB is designed for those seeking a reliable and powerful trimming solution. Its combination of a strong engine, intuitive features, and user-friendly design makes it an excellent addition to any lawn care toolkit. Whether you are a seasoned professional or a weekend warrior, this trimmer will help you achieve a well-manicured landscape with ease and efficiency.