Weed Eater WET1742STB manual Tools Required for Assembly, To Remove Tractor from Carton

Page 6

ASSEMBLY

Your new tractor has been assembled at the factory with exception of those parts left unassembled for shipping purposes. To ensure safe and proper operation of your tractor all parts and hardware you assemble must be tightened securely. Use the correct tools as necessary to insure proper tightness.

TOOLS REQUIRED FOR ASSEMBLY

A socket wrench set will make assembly easier. Standard wrench sizes are listed.

(2)

7/16" wrenches

Utility knife

(2)

3/4" wrench

Tire pressure gauge

Pliers

When right or left hand is mentioned in this manual, it means when you are in the operating position (seated behind the steering wheel).

TO REMOVE TRACTOR FROM CARTON

UNPACK CARTON

Remove all accessible loose parts and parts cartons from carton.

Cut along dotted lines on all four panels of carton. Remove end panels and lay side panels flat.

Check for any additional loose parts or cartons and remove.

BEFORE REMOVING TRACTOR FROM SKID

ATTACH STEERING WHEEL (See Fig. 1)

ASSEMBLE EXTENSION SHAFT AND BOOT

Slide extension shaft onto lower steering shaft. Align mounting holes in extension and lower shafts and install 1/4 hex bolt and locknut. Tighten securely.

IMPORTANT: TIGHTEN BOLT AND NUT SECURELY TO 10-12 FT. LBS TORQUE.

Place tabs of steering boot over tab slots in dash and push down to secure.

INSTALL STEERING WHEEL

Position front wheels of the tractor so they are pointing straight forward.

Remove steering wheel adapter from steering wheel and slide adapter onto steering shaft extension.

Position steering wheel so cross bars are horizontal (left to right) and slide inside boot and onto adapter.

Assemble large flat washer, 1/2 hex nut and tighten securely.

Snap steering wheel insert into center of steering wheel.

Remove protective materials from tractor hood and grill.

IMPORTANT: CHECK FOR AND REMOVE ANY STAPLES IN SKIDTHAT MAY PUNCTURETIRESWHERETRACTOR IS TO ROLL OFF SKID.

 

INSERT

 

1/2 HEX NUT

 

LARGE FLAT

 

WASHER

STEERING

 

WHEEL

STEERING

 

 

BOOT

 

TABS

ADAPTER

 

 

EXTENSION SHAFT

 

1/4 HEX BOLT

1/4 LOCKNUT

 

LOWER

 

STEERING

 

SHAFT

 

 

TAB

 

SLOTS

FIG. 1

6

Image 6
Contents Model NO. WET1742STB Safety Rules Safety Rules Table of Contents Contents of Hardware Pack To Remove Tractor from Carton AssemblyTools Required for Assembly Before Removing Tractor from SkidInstall Seat See Fig Check Battery See FigCheck for Proper Position of ALL Belts Check Tire PressureCheck Deck Levelness Check Brake SystemOperation Know Your Tractor HOW to USE Your Tractor Before Starting the Engine Mowing Tips To Start Engine See FigGeneral Recommendations MaintenanceLubrication Chart Before Each USETractor Engine Spark Plugs CleaningMuffler IN-LINE Fuel Filter See FigService and Adjustments To Install Mower See FigTo Remove Mower See Fig To Replace Mower Blade Drive Belt See Fig To Level Mower HousingBelt Installation Belt RemovalTo Replace Motion Drive Belt See Fig To Check and Adjust Brake See FigTo Adjust Brake To Check BrakeFront Wheel TOE-IN/CAMBER To Adjust Steering Wheel ALIGN- MentTransaxle Gear Shift Lever NEUTRAL- Adjustment See Fig To Remove Wheel for Repairs See FigTo Attach Jumper Cables To Start Engine with a Weak Battery See FigReplacing Battery See Figs To Remove CABLES, Reverse OrderTo Adjust Carburetor To Adjust Throttle Control CableTo Adjust Choke Control To Replace Headlight BulbFuel System StorageOther Engine OILTroubleshooting Points With attachment clutch Limited Warranty Policy Suggested Guide for Sighting Slopes for Safe Operation Only Ride UP and Down Hill Not Across Hill Degrees MAX

WET1742STB specifications

The Weed Eater WET1742STB is a versatile and efficient tool designed for homeowners and landscaping professionals alike. This gas-powered trimmer offers exceptional performance, making it an ideal choice for tackling tough overgrowth and maintaining a neat lawn.

One of the standout features of the WET1742STB is its powerful 17cc engine. This robust engine delivers reliable power, ensuring that users can easily handle various types of vegetation, from light grass to thicker weeds. The trimmer's speed is complemented by a straight shaft design, which allows for greater reach and maneuverability, making it easier to trim in hard-to-reach areas.

A key technology incorporated into this model is the dual line feed system. This feature enables the user to efficiently release more cutting line as needed, allowing for a wider cutting swath with each pass. This translates to reduced trimming time and enhanced productivity. The auto-feed spool ensures that the cutting line is replenished automatically, minimizing interruptions during operation.

Comfort and usability are also central to the design of the WET1742STB. It is equipped with a soft grip handle that reduces vibrations, enhancing user comfort during extended use. The lightweight design further adds to its ease of handling, allowing for extended periods of operation without causing undue fatigue. Additionally, the trimmer features an ergonomic throttle control that allows for precise speed adjustments.

One of the notable safety features of the WET1742STB is its protective guard, which shields the user from debris while trimming. This is especially important when tackling unruly growth, as it promotes safer operation without compromising efficiency.

Maintenance is simplified with the WET1742STB, thanks to its easy-access air filter and spark plug. This design feature ensures that users can quickly perform routine maintenance tasks, helping to extend the life of the trimmer and maintain peak performance.

In summary, the Weed Eater WET1742STB is designed for those seeking a reliable and powerful trimming solution. Its combination of a strong engine, intuitive features, and user-friendly design makes it an excellent addition to any lawn care toolkit. Whether you are a seasoned professional or a weekend warrior, this trimmer will help you achieve a well-manicured landscape with ease and efficiency.