Weed Eater WE16542D owner manual To Adjust Brake See Fig, To Replace Motion Drive Belt See Fig

Page 21

SERVICE AND ADJUSTMENTS

TO ADJUST BRAKE (See Fig. 21)

Your tractor is equipped with an adjustable brake system which is mounted on the right side of the transaxle.

If tractor requires more than six (6) feet stopping distance at high speed in highest gear, then brake must be adjusted.

•Depress clutch/brake pedal and engage parking brake.

•Measure distance between brake operating arm and nut “A” on brake rod.

•If distance is other than 1-1/2", loosen jam nut and turn nut “A” until distance becomes 1-1/2". Retighten jam nut against nut “A”.

•Road test tractor for proper stopping distance as stated above. Readjust if necessary. If stopping distance is still greater than six (6) feet in highest gear, further maintenance is necessary. Contact your nearest au- thorized service center/department.

WITH PARKING BRAKE "ENGAGED"

1-1/2"

NUT "A"

JAM NUT

OPERATING

ARM

FIG. 21

TO REPLACE MOTION DRIVE BELT (See Fig. 22)

Park the tractor on level surface. Engage parking brake. For assistance, there is a belt installation guide decal on bottom side of left footrest.

•Remove mower (See “TO REMOVE MOWER” in this section of this manual.)

•Remove belt from stationary idler and clutching idler.

•Pull belt slack toward rear of tractor. Remove belt upwards from transaxle pulley by deflecting belt keep- ers.

•Pull belt toward front of tractor and remove downwards from around engine pulley.

•Install new belt by reversing above procedure.

ENGINE

PULLEY

CLUTCHING

IDLER

STATIONARY

IDLER

TRANSAXLE

PULLEY

FIG. 22

TRANSAXLE GEAR SHIFT LEVER NEUTRAL ADJUSTMENT (See Fig. 23)

The transaxle should be in neutral when the gear shift lever is in neutral (N) (lock gate) position. The adjustment is preset at the factory; however, if adjustment is needed, proceed as follows:

•Make sure transaxle is in neutral (N).

NOTE: When the tractor rear wheels move freely, the transaxle is in neutral.

•Loosen adjustment bolt in front of the right rear wheel.

•Position the gear shift lever in the neutral (N) position.

•Tighten adjustment bolt securely.

NOTE: If additional clearance is needed to get to adjustment bolt, move mower deck height to the lowest position.

GEARSHIFT LEVER

NEUTRAL

LOCK GATE

ADJUSTMENT

BOLT

FIG. 23

TO ADJUST STEERING WHEEL ALIGNMENT

If steering wheel crossbars are not horizontal (left to right) when wheels are positioned straight forward, remove steer- ing wheel and reassemble per instructions in the Assembly section of this manual.

FRONT WHEEL TOE-IN/CAMBER

The front wheel toe-in and camber are not adjustable on your tractor. If damage has occurred to affect the front wheel toe- in or camber, contact your nearest authorized service center/department.

21

Page 20 Page 22
Image 21
Page 20 Page 22
Contents Model NO. WE16542D IV. Service Safety RulesGeneral Operation II. Slope OperationTable of Contents Customer Responsibilities Product SpecificationsUnassembled Parts Steering Wheel SeatKeys Tools Required for Assembly AssemblyTo Remove Tractor from Carton Before Removing Tractor from SkidHOW to SET UP Your Tractor Check Battery See FigInstall Seat See Fig Check Deck Levelness Check Tire PressureCheck for Proper Position of ALL Belts Check Brake SystemOperation Know Your Tractor To USE Throttle Control see FIG HOW to USE Your TractorTo Operate on Hills Before Starting the EngineTo Transport Towing Carts and Other ATTACH- MentsMowing Tips ADD GasolineTo Start Engine See Fig Customer Responsibilities Lubrication ChartGeneral Recommendations Before Each USEBrake Operation TractorTires Operator Presence SystemEngine BatteryBelts Transaxle CoolingTo Service PRE-CLEANER Clean AIR ScreenTo Service Cartridge Engine Cooling Fins See FigMuffler CleaningSpark Plugs IN-LINE Fuel Filter See FigService and Adjustments To Install Mower See FigTo Remove Mower See Fig Belt Installation To Level Mower HousingTo Replace Mower Blade Drive Belt See Fig Belt RemovalTransaxle Gear Shift Lever Neutral Adjustment See Fig To Adjust Brake See FigTo Adjust Steering Wheel Alignment To Replace Motion Drive Belt See FigReplacing Battery See Figs To Start Engine with a Weak Battery See FigTo Remove Wheel for Repairs See Fig To Attach Jumper CablesTo Replace Headlight Bulb To Adjust CarburetorInterlocks and Relays To Replace FuseOther StorageFuel System Engine OILTroubleshooting Points OFF Tractor - Model Number WE16542D SchematicElectrical KEY Part NO. NO.DESCRIPTION Chassis and Enclosures KEY Part Description Drive 72140608 Steering Assembly KEY Part NO. NO.DESCRIPTION Spark Arrester Optional Equipment174642 Seat Assembly Wheels & Tires DecalsMower Lift Nut Lock w/Wsh 1/2-13 Unc Mower Deck Repair Parts Service Notes Limited Warranty For Limited WarrantiesSlope Sighting Guide CUT This OUT Dotted Is a

WE16542D specifications

The Weed Eater WE16542D is a versatile and powerful string trimmer designed to make lawn care and landscaping tasks easier and more efficient. Built with user convenience and performance in mind, this model has gained popularity among both homeowners and landscaping professionals.

One of the standout features of the WE16542D is its lightweight design. Weighing in at just over 10 pounds, it is easily maneuverable, allowing users to trim grass and weeds without feeling fatigued during long periods of use. The trimmer is equipped with a 16-inch cutting swath, providing ample coverage for tackling larger areas quickly while still allowing for precision around flower beds and other landscaping features.

Powering the WE16542D is a reliable 42cc two-cycle gas engine, which delivers robust performance. This engine provides a good balance of power and efficiency, enabling users to handle tougher jobs without a loss of performance. The trimmer also features an easy-start system, ensuring that users can get to work without the frustration of struggling with difficult pull starts.

The Weed Eater WE16542D incorporates a dual-line cutting system with a bump feed head. This technology allows users to effortlessly advance the cutting line while working, which is particularly useful for maintaining a seamless cutting experience. The trimmer's dual-line system ensures a clean and efficient cut, resulting in a more pristine lawn.

Additionally, the trimmer boasts an adjustable ergonomic handle, giving users the ability to customize the grip and orientation to fit their height and comfort level. This thoughtful design feature minimizes user strain, making it ideal for prolonged use. The WE16542D is also equipped with a vibration-reduction system, further enhancing user comfort by reducing the impact of vibrations during operation.

Durability is another hallmark of the Weed Eater WE16542D. The construction is robust, designed to withstand the rigors of outdoor use while maintaining performance over time. With proper care and maintenance, users can expect this trimmer to serve them for many seasons.

In summary, the Weed Eater WE16542D combines lightweight design, powerful performance, and user-friendly features to provide an effective solution for lawn maintenance. Whether you are a homeowner looking to keep your garden pristine or a professional landscaper managing various properties, this trimmer offers reliability and efficiency for all your trimming needs.
Top Page Image Contents