Weed Eater WE16542D owner manual To Remove Wheel for Repairs See Fig, Replacing Battery See Figs

Page 22

SERVICE AND ADJUSTMENTS

TO REMOVE WHEEL FOR REPAIRS (See Fig. 24)

•Block up axle securely.

•Remove axle cover, retaining ring and washers to allow wheel removal (rear wheel contains a square key - Do not lose).

•Repair tire and reassemble.

•On rear wheels only: align grooves in rear wheel hub and axle. Insert square key.

•Replace washers and snap retaining ring securely in axle groove.

•Replace axle cover.

NOTE: To seal tire punctures and prevent flat tires due to slow leaks, tire sealant may be purchased from your local parts dealer. Tire sealant also prevents tire dry rot and corrosion.

WASHERS

RETAINING

RING

AXLE COVER

SQUARE KEY (REAR

 

WHEEL ONLY)

 

FIG. 24

TO START ENGINE WITH A WEAK BATTERY (See Fig. 25)

CAUTION: Lead-acid batteries generate explosive gases. Keep sparks, flame and smoking materials away from bat- teries. Always wear eye protection when around batteries.

If your battery is too weak to start the engine, it should be recharged. (See "BATTERY" in the Customer Responsibili- ties section of this manual).

If “jumper cables” are used for emergency starting, follow this procedure:

IMPORTANT: YOUR TRACTOR IS EQUIPPED WITH A 12 VOLT NEGATIVE GROUNDED SYSTEM. THE OTHER VEHICLE MUST ALSO BE A 12 VOLT NEGATIVE GROUNDED SYSTEM. DO NOT USE YOUR TRACTOR BATTERY TO START OTHER VEHICLES.

TO ATTACH JUMPER CABLES -

•Connect each end of the RED cable to the POSITIVE (+) terminal of each battery, taking care not to short against chassis.

•Connect one end of the BLACK cable to the NEGATIVE (-) terminal of fully charged battery.

•Connect the other end of the BLACK cable to good CHASSIS GROUND, away from fuel tank and battery.

TO REMOVE CABLES, REVERSE ORDER -

•BLACK cable first from chassis and then from the fully charged battery.

•RED cable last from both batteries.

POSITIVE TERMINAL

 

NEGATIVE TERMINAL

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

CHASSIS

 

 

CABLES

POSITIVE

NEGATIVE

TERMINAL

TERMINAL

CHARGED

 

 

BATTERY

FIG. 25

REPLACING BATTERY (See Figs. 26 AND 27)

CAUTION: Do not short battery termi- nals by allowing a wrench or any other object to contact both terminals at the same time. Before connecting battery, remove metal bracelets, wristwatch bands, rings, etc.

Positive terminal must be connected first to prevent sparking from acciden- tal grounding.

•Lift seat pan to raised position and open battery box door.

•Disconnect BLACK battery cable first then RED battery cable and carefully remove battery from tractor.

•Install new battery with terminals in same position as old battery.

•First connect RED battery cable to positive (+) terminal with hex bolt and keps nut as shown. Tighten securely.

•Connect BLACK grounding cable to negative (-) terminal with remaining hex bolt and keps nut. Tighten securely.

•Close battery box door.

SEAT PAN

BATTERY

BOX DOOR

FIG. 26

22

Page 21 Page 23
Image 22
Page 21 Page 23
Contents Model NO. WE16542D General Operation Safety RulesIV. Service II. Slope OperationTable of Contents Product Specifications Customer ResponsibilitiesSteering Wheel Seat Unassembled PartsKeys To Remove Tractor from Carton AssemblyTools Required for Assembly Before Removing Tractor from SkidCheck Battery See Fig HOW to SET UP Your TractorInstall Seat See Fig Check for Proper Position of ALL Belts Check Tire PressureCheck Deck Levelness Check Brake SystemOperation Know Your Tractor HOW to USE Your Tractor To USE Throttle Control see FIGTo Transport Before Starting the EngineTo Operate on Hills Towing Carts and Other ATTACH- MentsADD Gasoline Mowing TipsTo Start Engine See Fig General Recommendations Lubrication ChartCustomer Responsibilities Before Each USETires TractorBrake Operation Operator Presence SystemBelts BatteryEngine Transaxle CoolingTo Service Cartridge Clean AIR ScreenTo Service PRE-CLEANER Engine Cooling Fins See FigSpark Plugs CleaningMuffler IN-LINE Fuel Filter See FigTo Install Mower See Fig Service and AdjustmentsTo Remove Mower See Fig To Replace Mower Blade Drive Belt See Fig To Level Mower HousingBelt Installation Belt RemovalTo Adjust Steering Wheel Alignment To Adjust Brake See FigTransaxle Gear Shift Lever Neutral Adjustment See Fig To Replace Motion Drive Belt See FigTo Remove Wheel for Repairs See Fig To Start Engine with a Weak Battery See FigReplacing Battery See Figs To Attach Jumper CablesInterlocks and Relays To Adjust CarburetorTo Replace Headlight Bulb To Replace FuseFuel System StorageOther Engine OILTroubleshooting Points OFF Schematic Tractor - Model Number WE16542DElectrical KEY Part NO. NO.DESCRIPTION Chassis and Enclosures KEY Part Description Drive 72140608 Steering Assembly KEY Part NO. NO.DESCRIPTION Optional Equipment Spark Arrester174642 Seat Assembly Decals Wheels & TiresMower Lift Nut Lock w/Wsh 1/2-13 Unc Mower Deck Repair Parts Service Notes Limited Warranty Limited Warranties ForSighting Guide CUT This OUT Dotted Is a Slope

WE16542D specifications

The Weed Eater WE16542D is a versatile and powerful string trimmer designed to make lawn care and landscaping tasks easier and more efficient. Built with user convenience and performance in mind, this model has gained popularity among both homeowners and landscaping professionals.

One of the standout features of the WE16542D is its lightweight design. Weighing in at just over 10 pounds, it is easily maneuverable, allowing users to trim grass and weeds without feeling fatigued during long periods of use. The trimmer is equipped with a 16-inch cutting swath, providing ample coverage for tackling larger areas quickly while still allowing for precision around flower beds and other landscaping features.

Powering the WE16542D is a reliable 42cc two-cycle gas engine, which delivers robust performance. This engine provides a good balance of power and efficiency, enabling users to handle tougher jobs without a loss of performance. The trimmer also features an easy-start system, ensuring that users can get to work without the frustration of struggling with difficult pull starts.

The Weed Eater WE16542D incorporates a dual-line cutting system with a bump feed head. This technology allows users to effortlessly advance the cutting line while working, which is particularly useful for maintaining a seamless cutting experience. The trimmer's dual-line system ensures a clean and efficient cut, resulting in a more pristine lawn.

Additionally, the trimmer boasts an adjustable ergonomic handle, giving users the ability to customize the grip and orientation to fit their height and comfort level. This thoughtful design feature minimizes user strain, making it ideal for prolonged use. The WE16542D is also equipped with a vibration-reduction system, further enhancing user comfort by reducing the impact of vibrations during operation.

Durability is another hallmark of the Weed Eater WE16542D. The construction is robust, designed to withstand the rigors of outdoor use while maintaining performance over time. With proper care and maintenance, users can expect this trimmer to serve them for many seasons.

In summary, the Weed Eater WE16542D combines lightweight design, powerful performance, and user-friendly features to provide an effective solution for lawn maintenance. Whether you are a homeowner looking to keep your garden pristine or a professional landscaper managing various properties, this trimmer offers reliability and efficiency for all your trimming needs.
Top Page Image Contents