Weed Eater 545186750 Collection BAG Assembly, Adjusting the Shoulder Strap on the Collection BAG

Page 6

4.To attach the lower vacuum tube to the upper vacuum tube, first align the arrows on the two tubes. Then, press the two tubes together until the lower tube is securely seated in the upper tube (about 3 inches).

Upper Tube Lower Tube

Align arrows on upper and lower tubes

COLLECTION BAG ASSEMBLY

1.Open the zipper on the collection bag and insert the elbow tube.

2.Push the small end of the elbow tube through the small opening in the bag.

NOTE: Make sure edge of the small opening is flush against the flared area of the elbow tube and the hole for the tube release button is on top.

Elbow Tube

Tube

 

Release

 

Button

 

Hole

Zipper

Small

Opening

Opening

 

3.Close the zipper on the bag. Make sure the zipper is closed completely.

4.Align the grooves on the elbow tube with the grooves on the blower outlet.

5.Push the elbow tube onto the blower outlet until it snaps into place (elbow tube is secured by red tube release button).

ADJUSTING THE SHOULDER STRAP ON THE COLLECTION BAG

1.Carefully loop the shoulder strap through the buckle as shown in the il- lustration below.

Last In

First In

2.Position the unit on your right-hand side, blower outlet and bag pointing toward the rear. Hold the unit in an upright position with the lower vacu- um tube on the ground to support it.

3.Place the shoulder strap over your head and onto your left shoulder.

4.Adjust the strap to allow a free flow of air from the blower. If the collection bag is kinked, the unit will not operate properly.

NOTE: The strap is designed to posi- tion the collection bag on your shoulder without kinks. The strap is not intended to support the weight of the unit.

Shoulder strap on left shoulder

No kinks in bag allows free air flow

HOW TO CONVERT UNIT FROM VACUUM USE TO BLOWER USE

1.Stop unit and unplug the extension cord.

2.Remove the vacuum tubes by insert- ing the tip of a screwdriver into the latch area on the vacuum assist han- dle. Gently tilt handle of screwdriver toward the front of the unit to release the latch while pulling up on the vacu- um assist handle with your other hand.

Latch Area

Vacuum

Assist

Handle

3.Install the inlet restrictor that was re- moved when assembling for vacuum use.

NOTE: If you are unable to locate the inlet restrictor, the unit will still operate. This restrictor improves the blower function.

4.Remove the collection bag.

5.Close the inlet cover and make sure it is latched closed.

6.Re-install the blower tube. Refer to AT- TACHING THE BLOWER TUBE for instructions on how to attach this item.

SELECT AN EXTENSION CORD

Use only a 120 A.C. voltage supply as shown on nameplate of the unit to power your blower.

6

Page 5 Page 7
Image 6
Page 5 Page 7
Contents Advertencia EnglishEspañol Français AvertissementSafety Rules Operator SafetyElectrical Safety Double Insulation Construction UNIT/MAINTENANCE SafetyStop the motor immediately if you are ap- proached Servicing of Double Insulated BLOWER/VACUUMUse only in daylight or in good artificial light Blower SafetyVacuum Safety StandardsVacuum Assembly AssemblyBlower Assembly Standard screwdriver is required for as- semblyHOW to Convert Unit from Vacuum USE to Blower USE Collection BAG AssemblyAdjusting the Shoulder Strap on the Collection BAG Stop unit and unplug the extension cordON/OFF Switch Inlet Cover Latch ON/OFF Switch is used to activateKnow Your Electric BLOWER/VACUUM Maintenance Before Each USEService StorageAfter Each USE Troubleshooting Table Symptom Cause Remedy Weed EaterTerry Fox Way Mississauga,Ontario L5V3E4

545186750 specifications

The Weed Eater 545186750 is a powerful and efficient tool designed for homeowners and landscaping professionals alike. This versatile trimmer offers a combination of features that ensure a clean and precise cut, making it an essential addition to any outdoor maintenance arsenal.

One of the standout characteristics of the Weed Eater 545186750 is its 25cc two-cycle engine. This engine provides ample power to tackle tough weeds, grass, and overgrowth with ease. The lightweight design of the trimmer allows for easy maneuverability, enabling users to work in tight spaces or navigate around flower beds and garden edges without difficulty.

Equipped with a durable dual-line cutting system, the Weed Eater 545186750 ensures efficiency and effectiveness during operation. The trimmer uses a 0.095-inch line, which is ideal for cutting through thick vegetation, while the automatic bump feed system allows users to easily advance the line as needed, eliminating downtime and enhancing productivity.

The design of the Weed Eater 545186750 incorporates a straight shaft, which provides better reach and access to hard-to-reach areas. This feature is particularly beneficial for those tackling tall grass or weeds in challenging locations. Additionally, the trimmer comes equipped with a comfort grip handle, reducing fatigue during extended use and ensuring a more enjoyable experience.

Safety is also a key focus in the design of the Weed Eater 545186750. It features an integrated safety guard that protects the user from debris while cutting. Furthermore, the trimmer’s lightweight nature and balanced design contribute to its ease of use, making it suitable for users of all experience levels.

The user-friendly start system is another important aspect of the Weed Eater 545186750. With an easy-start technology, users can expect reliable starts with minimal effort, allowing them to get to work without frustration.

In summary, the Weed Eater 545186750 is a dependable and effective string trimmer that combines power, comfort, and ease of use. Its advanced features and thoughtful design make it a great choice for anyone looking to maintain a tidy yard or tackle landscaping projects. With its performance and efficiency, this trimmer is sure to meet the needs of a variety of users, from casual gardeners to professional landscapers.
Top Page Image Contents