Weed Eater 178277 To Adjust Throttle Control Cable, To Replace Headlight Bulb, To Replace Fuse

Page 24

SERVICE AND ADJUSTMENTS

REPLACING BATTERY (See Fig. 29)

CAUTION: Do not short battery termi- nals by allowing a wrench or any other object to contact both terminals at the same time. Before connecting battery, remove metal bracelets, wristwatch bands, rings, etc.

Positive terminal must be connected first to prevent sparking from accidental grounding.

•Lift hood to raised position.

•Remove terminal guard.

•Disconnect BLACK battery cable then RED battery cable and carefully remove battery from tractor.

•Install new battery with terminals in same position as old battery.

•Reinstall terminal guard.

•First connect RED battery cable to positive (+) battery terminal with hex bolt and keps nut as shown. Tighten securely.

•Connect BLACK grounding cable to negative (-) battery terminal with remaining hex bolt and keps nut. Tighten securely

•Close terminal access doors.

•Close hood.

TO REMOVE HOOD AND GRILL ASSEMBLY (See Fig. 30)

•Raise hood.

•Unsnap headlight wire connector.

•Stand in front of tractor. Grasp hood at sides, tilt toward engine and lift off of tractor.

•To replace, reverse above procedure.

HOOD

HEADLIGHT

WIRE

CONNECTOR

FIG. 30

ENGINE

Maintenance, repair, or replacement of the emission control

KEPS NUT

TERMINAL ACCESS DOOR

TERMINAL

GUARD

HEX BOLT

POSITIVE (RED) CABLE

NEGATIVE (BLACK) CABLE

devices and systems, which are being done at the custom- ers expense, may be performed by any non-road engine repair establishment or individual. Warranty repairs must be performed by an authorized engine manufacturer's service outlet.

TO ADJUST THROTTLE CONTROL CABLE

The throttle control has been preset at the factory and adjustment should not be necessary. Check adjustment as described below before loosening cable. If adjustment is

FIG. 29

TO REPLACE HEADLIGHT BULB

•Raise hood.

•Pull bulb holder out of the hole in the backside of the grill.

•Replace bulb in holder and push bulb holder securely back into the hole in the backside of the grill.

•Close hood.

INTERLOCKS AND RELAYS

Loose or damaged wiring may cause your tractor to run poorly, stop running, or prevent it from starting.

•Check wiring. See electrical wiring diagram in the Repair Parts section.

TO REPLACE FUSE

Replace with 20 amp automotive-type plug-in fuse. The fuse holder is located behind the dash.

necessary, see engine manual.

TO ADJUST CHOKE CONTROL

The choke control has been preset at the factory and adjustment should not be necessary. Check adjustment as described below before loosening cable. If adjustment is necessary, see engine manual.

TO ADJUST CARBURETOR

The carburetor has been preset at the factory and adjust- ment should not be necessary. However, minor adjustment may be required to compensate for differences in fuel, temperature, altitude or load. If the carburetor does need adjustment, see engine manual.

IMPORTANT: NEVER TAMPER WITH THE ENGINE GOVERNOR, WHICH IS FACTORY SET FOR PROPER ENGINE SPEED. OVERSPEEDING THE ENGINE ABOVE THE FACTORY HIGH SPEED SETTING CAN BE DANGEROUS. IF YOU THINK THE ENGINE-GOVERNED HIGH SPEED NEEDS ADJUSTING, CONTACT YOUR N E A R E S T A U T H O R I Z E D S E R V I C E C E N T E R / DEPARTMENT, WHICH HAS PROPER EQUIPMENT AND E X P E R I E N C E T O M A K E A N Y N E C E S S A R Y ADJUSTMENTS.

24

Page 23 Page 25
Image 24
Page 23 Page 25
Contents Model NO. SGT18H46B Safety Rules Safe Operation Practices for Ride-On MowersSafety Rules Table of Contents Unassembled Parts Steering WheelGauge Wheels Slope SheetAssembly Tools Required for AssemblyHOW to SET UP Your Tractor To Remove Tractor from CartonInstall Seat See Fig To Attach Nose Roller See FigInstall Mower and Drive Belt See Figs Check Tire Pressure Check Deck LevelnessCheck for Proper Position of ALL Belts Check Brake SystemOperation Know Your Tractor HOW to USE Your Tractor To Adjust Gauge Wheels See Fig To Operate Mower See FigTo Operate on Hills To Transport See FigsBefore Starting the Engine Check Engine OIL Level See FigADD Gasoline To Start Engine See FigMowing Tips Purge TransmissionCustomer Responsibilities General RecommendationsBefore Each USE Tractor Engine Cleaning Engine Cooling FinsAIR Filter MufflerService and Adjustments To Install MowerTo Level Mower Housing To Remove Mower See FigFRONT-TO-BACK Adjustment See Figs To Replace Mower Drive BeltTo Adjust Brake See Fig To Replace Mower Blade Drive Belt See FigTo Replace Motion Drive Belt See Fig Transmission REMOVAL/REPLACEMENT To Adjust Steering Wheel AlignmentFront Wheel TOE-IN/CAMBER To Adjust Throttle Control Cable To Adjust Choke ControlTo Adjust Carburetor To Replace Headlight BulbStorage OtherFuel System Engine OILTroubleshooting Points OFF Service Notes Schematic Tractor - Model Number SGT18H46BElectrical KEY Part NO. NO.DESCRIPTION Chassis KEY Part Description Drive 161399 Steering Assembly KEY Part NO. NO.DESCRIPTION Engine 176174 Control, Throttle Seat Assembly Decals Wheels & TiresMower Lift Washer 13/32 x 5/8 x 16 Ga Mower Deck KEY Part Description Limited Warranty Suggested Guide for Sighting Slopes for Safe Operation Sighting Guide

178277 specifications

The Weed Eater 178277 is a versatile and efficient tool designed for homeowners and gardening enthusiasts who seek a reliable solution for maintaining their lawns and gardens. This string trimmer stands out for its combination of powerful performance, user-friendly design, and modern technologies that enhance its functionality.

One of the key features of the Weed Eater 178277 is its robust engine that facilitates easy starting and powerful cutting performance. The engine is engineered to provide enough torque to handle various types of vegetation, whether it’s delicate grass or tougher weeds. Additionally, the machine operates efficiently, which helps in conserving fuel and minimizing emissions, making it an eco-friendly choice.

The trimmer incorporates a 17-inch cutting width, allowing users to cover more ground with each pass. This feature significantly reduces the time and effort spent on lawn maintenance, making it an ideal choice for larger yards. The adjustable handle also enhances comfort and control during operation, enabling users to tackle different cutting angles and heights with ease.

Equipped with an automatic line advancement system, the Weed Eater 178277 ensures that the cutting line feeds smoothly as it wears down. This feature eliminates the need for manual adjustments, saving time and providing a hassle-free experience. The trimmer uses a dual-line system, which not only enhances cutting performance but also contributes to a cleaner line of cut.

Another notable technology featured in the Weed Eater 178277 is its lightweight design. Weighing in at just over 10 pounds, it is easy to maneuver and transport, making it perfect for prolonged use without causing strain to the user. This is particularly beneficial for those who may not have the physical strength to handle heavier trimmers.

Also, maintaining the Weed Eater 178277 is straightforward, thanks to its simplified maintenance access points. Users can quickly check and replace parts if necessary, ensuring the longevity of the trimmer.

In summary, the Weed Eater 178277 combines performance, convenience, and durability into a powerful package that appeals to both casual gardeners and serious lawn care enthusiasts. With its blend of innovative features and user-centric design, it is a reliable companion for keeping lawns looking pristine.
Top Page Image Contents