Weed Eater 180530 manual To Replace Headlight Bulb, Interlocks and Relays, To Replace Fuse, Engine

Page 23

SERVICE AND ADJUSTMENTS

KEPS

NUT

HEX

BOLT

POSITIVE (RED)

NEGATIVE

CABLE

(BLACK) CABLE

FIG. 27

TO REPLACE HEADLIGHT BULB

•Raise hood.

•Pull bulb holder out of the hole in the backside of the grill.

•Replace bulb in holder and push bulb holder securely back into the hole in the backside of the grill.

•Close hood.

INTERLOCKS AND RELAYS

Loose or damaged wiring may cause your tractor to run poorly, stop running, or prevent it from starting.

•Check wiring. See electrical wiring diagram in the Repair Parts section.

TO REPLACE FUSE

Replace with 20 amp automotive-type plug-in fuse. The fuse holder is located behind the dash.

TO REMOVE HOOD AND GRILL ASSEMBLY (See Fig. 28)

•Raise hood.

•Unsnap headlight wire connector.

•Stand in front of tractor. Grasp hood at sides, tilt toward engine and lift off of tractor.

•To replace, reverse above procedure.

HOOD

HEADLIGHT

WIRE

CONNECTOR

FIG. 28

ENGINE

TO ADJUST THROTTLE CONTROL CABLE (See Fig. 29)

The throttle control has been preset at the factory and adjustment should not be necessary. Check adjustment as described below before loosening cable. If adjustment is necessary, proceed as follows:

•With engine not running, move throttle control lever from slow to choke position. Slowly move lever from choke to fast position.

•Check that holes “A” in governor control lever and hole in governor plate line-up. If holes “A” are not aligned, loosen clamp screw and move throttle cable until holes are aligned. Tighten clamp screw securely.

 

GOVERNOR

GOVERNOR

 

CONTROL

 

CONTROL LEVER

 

PLATE

 

 

HOLES “A”

CLAMP

THROTTLE

 

SCREW

CABLE

 

 

FIG. 29

TO ADJUST CARBURETOR

The carburetor has been preset at the factory and adjust- ment should not be necessary. However, minor adjustment may be required to compensate for differences in fuel, temperature, altitude or load. If the carburetor does need adjustment, see engine manual.

High speed stop is factory adjusted. Do not adjust - damage may result.

IMPORTANT: NEVER TAMPER WITH THE ENGINE GOVERNOR, WHICH IS FACTORY SET FOR PROPER ENGINE SPEED. OVERSPEEDING THE ENGINE ABOVE T H E F A C T O R Y H I G H S P E E D S E T T I N G C A N B E DANGEROUS. IF YOU THINK THE ENGINE-GOVERNED HIGH SPEED NEEDS ADJUSTING, CONTACT YOUR N E A R E S T A U T H O R I Z E D S E R V I C E C E N T E R / DEPARTMENT, WHICH HAS PROPER EQUIPMENT AND E X P E R I E N C E T O M A K E A N Y N E C E S S A R Y ADJUSTMENTS.

23

Page 22 Page 24
Image 23
Page 22 Page 24
Contents Model NO. WE16542E II. Slope Operation Safety RulesIV. Service General OperationTable of Contents Customer Responsibilities Product SpecificationsKeys Unassembled PartsSteering Wheel Seat Before Removing Tractor from Skid AssemblyTools Required for Assembly To Remove Tractor from CartonInstall Seat See Fig HOW to SET UP Your TractorCheck Battery See Fig Check Brake System Check Tire PressureCheck Deck Levelness Check for Proper Position of ALL BeltsOperation Know Your Tractor To USE Throttle Control see FIG HOW to USE Your TractorTowing Carts and Other ATTACH- Ments Before Starting the EngineTo Operate on Hills To TransportTo Start Engine See Fig Mowing TipsADD Gasoline Before Each USE ¿ Lubrication ChartCustomer Responsibilities General RecommendationsOperator Presence System TractorBrake Operation TiresTransaxle Cooling BatteryEngine BeltsEngine Cooling Fins See Fig Clean AIR ScreenTo Service PRE-CLEANER To Service CartridgeIN-LINE Fuel Filter See Fig CleaningMuffler Spark PlugsTo Remove Mower See Fig Service and AdjustmentsTo Install Mower See Fig Belt Removal To Level Mower HousingBelt Installation To Replace Mower Blade Drive Belt See FigTo Replace Motion Drive Belt See Fig To Adjust Brake See FigTransaxle Gear Shift Lever Neutral Adjustment See Fig To Adjust Steering Wheel AlignmentTo Attach Jumper Cables To Start Engine with a Weak Battery See FigReplacing Battery See Figs To Remove Wheel for Repairs See FigTo Replace Fuse To Adjust CarburetorTo Replace Headlight Bulb Interlocks and RelaysEngine OIL StorageOther Fuel SystemTroubleshooting Points OFF Tractor - Model Number WE16542E Schematic2122 Electrical178861 178437Chassis and Enclosures 17490608 174620Drive 179114 175765175456 175578Steering Assembly 175118 175121177876 175146Spark Arrester Optional Equipment170551 Control Throt/Ch Lh Seat Assembly 180531 DecalsWheels & Tires 180530Mower Lift 175689 143 159 144 150 Mower Deck179292 174493173984 178342Service Notes Limited Warranty C U M SEH Suggested Guide for Sighting Slopes for Safe Operation

180530 specifications

The Weed Eater 180530 is a powerful and efficient string trimmer designed to make yard maintenance easier and more effective. With its robust features and modern technology, this tool stands out as a reliable choice for both amateur gardeners and professional landscapers.

One of the main features of the 180530 is its lightweight design, allowing for easy maneuverability and reduced user fatigue during extended use. Weighing in at just around 8 pounds, it is easy to handle, making it suitable for users of all experience levels.

Powering the Weed Eater 180530 is a 25cc 2-cycle engine, which delivers impressive performance and efficiency. This engine provides rapid acceleration and effective cutting capabilities, allowing users to tackle tough weeds and thick grass with ease. The 2-cycle engine design is known for its simplicity and ease of maintenance, ensuring that users can quickly get back to work.

The 180530 features an automatic dual line feed system, which ensures that the cutting line is always at the optimal length during operation. This reduces downtime associated with manual line adjustments, thereby enhancing productivity. The trimmer is equipped with a straight shaft, which extends reach and makes it easier to access difficult areas.

Another standout characteristic of the Weed Eater 180530 is its versatility. This trimmer is designed to accept a variety of attachments, allowing users to switch between functions such as edging, blowing, and cultivating with ease. This adaptability provides excellent value for users who want a multi-functional landscape tool.

Safety is also prioritized in the design of the 180530. It comes with an easy-to-operate throttle control that allows users to manage the power output effectively. Additionally, the protective guard helps to shield the user from debris while operating, enhancing overall safety during use.

In conclusion, the Weed Eater 180530 combines powerful performance with a lightweight and user-friendly design. Its versatile capabilities, efficient engine technology, and safety features make it a valuable addition to any yard care toolkit. Whether tackling a small garden or maintaining larger landscapes, the 180530 is well-equipped to handle a variety of trimming tasks, ensuring beautifully maintained outdoor spaces.
Top Page Image Contents