Weed Eater 180530 manual Storage, Other, Fuel System, Engine OIL, Cylinders

Page 24

STORAGE

Immediately prepare your tractor for storage at the end of the season or if the tractor will not be used for 30 days or more.

CAUTION: Never store the tractor with gasoline in the tank inside a building where fumes may reach an open flame or spark. Allow the engine to cool before storing in any enclosure.

TRACTOR

Remove mower from tractor for winter storage. When mower is to be stored for a period of time, clean it thoroughly, remove all dirt, grease, leaves, etc. Store in a clean, dry area.

•Clean entire tractor (See “CLEANING” in the Customer Responsibilities section of this manual).

•Inspect and replace belts, if necessary (See belt re- placement instructions in the Service and Adjustments section of this manual).

•Lubricate as shown in the Customer Responsibilities section of this manual.

•Be sure that all nuts, bolts and screws are securely fastened. Inspect moving parts for damage, breakage and wear. Replace if necessary.

•Touch up all rusted or chipped paint surfaces; sand lightly before painting.

BATTERY

•Fully charge the battery for storage.

•After a period of time in storage, battery may require recharging.

•To help prevent corrosion and power leakage during long periods of storage, battery cables should be discon- nected and battery cleaned thoroughly (see “TO CLEAN BATTERY AND TERMINALS” in the Customer Respon- sibilities section of this manual).

•After cleaning, leave cables disconnected and place cables where they cannot come in contact with battery terminals.

•If battery is removed from tractor for storage, do not store battery directly on concrete or damp surfaces.

ENGINE

FUEL SYSTEM

IMPORTANT: IT IS IMPORTANT TO PREVENT GUM DEPOSITS FROM FORMING IN ESSENTIAL FUEL SYSTEM PARTS SUCH AS CARBURETOR, FUEL FILTER, FUEL

H O S E , O R T A N K D U R I N G S T O R A G E . A L S O , EXPERIENCE INDICATES THAT ALCOHOL BLENDED FUELS (CALLED GASOHOL OR USING ETHANOL OR METHANOL) CAN ATTRACT MOISTURE WHICH LEADS TO SEPARATION AND FORMATION OF ACIDS DURING STORAGE. ACIDIC GAS CAN DAMAGE THE FUEL SYSTEM OF AN ENGINE WHILE IN STORAGE.

•Drain the fuel tank.

•Start the engine and let it run until the fuel lines and carburetor are empty.

•Never use engine or carburetor cleaner products in the fuel tank or permanent damage may occur.

•Use fresh fuel next season.

NOTE: Fuel stabilizer is an acceptable alternative in minimizing the formation of fuel gum deposits during stor- age. Add stabilizer to gasoline in fuel tank or storage container. Always follow the mix ratio found on stabilizer container. Run engine at least 10 minutes after adding stabilizer to allow the stabilizer to reach the carburetor. Do not drain the gas tank and carburetor if using fuel stabilizer.

ENGINE OIL

Drain oil (with engine warm) and replace with clean engine oil. (See “ENGINE” in the Customer Responsibilities section of this manual).

CYLINDER(S)

•Remove spark plug(s).

•Pour one ounce of oil through spark plug hole(s) into cylinder(s).

•Turn ignition key to “START” position for a few seconds to distribute oil.

•Replace with new spark plug(s).

OTHER

•Do not store gasoline from one season to another.

•Replace your gasoline can if your can starts to rust. Rust and/or dirt in your gasoline will cause problems.

•If possible, store your tractor indoors and cover it to give protection from dust and dirt.

•Cover your tractor with a suitable protective cover that does not retain moisture. Do not use plastic. Plastic cannot breathe which allows condensation to form and will cause your tractor to rust.

IMPORTANT: NEVER COVER TRACTOR WHILE ENGINE AND EXHAUST AREAS ARE STILL WARM.

24

Page 23 Page 25
Image 24
Page 23 Page 25
Contents Model NO. WE16542E Safety Rules IV. ServiceGeneral Operation II. Slope OperationTable of Contents Product Specifications Customer ResponsibilitiesUnassembled Parts Steering Wheel SeatKeys Assembly Tools Required for AssemblyTo Remove Tractor from Carton Before Removing Tractor from SkidHOW to SET UP Your Tractor Check Battery See FigInstall Seat See Fig Check Tire Pressure Check Deck LevelnessCheck for Proper Position of ALL Belts Check Brake SystemOperation Know Your Tractor HOW to USE Your Tractor To USE Throttle Control see FIGBefore Starting the Engine To Operate on HillsTo Transport Towing Carts and Other ATTACH- MentsMowing Tips ADD GasolineTo Start Engine See Fig ¿ Lubrication Chart Customer ResponsibilitiesGeneral Recommendations Before Each USETractor Brake OperationTires Operator Presence SystemBattery EngineBelts Transaxle CoolingClean AIR Screen To Service PRE-CLEANERTo Service Cartridge Engine Cooling Fins See FigCleaning MufflerSpark Plugs IN-LINE Fuel Filter See FigService and Adjustments To Install Mower See FigTo Remove Mower See Fig To Level Mower Housing Belt InstallationTo Replace Mower Blade Drive Belt See Fig Belt RemovalTo Adjust Brake See Fig Transaxle Gear Shift Lever Neutral Adjustment See FigTo Adjust Steering Wheel Alignment To Replace Motion Drive Belt See FigTo Start Engine with a Weak Battery See Fig Replacing Battery See FigsTo Remove Wheel for Repairs See Fig To Attach Jumper CablesTo Adjust Carburetor To Replace Headlight BulbInterlocks and Relays To Replace FuseStorage OtherFuel System Engine OILTroubleshooting Points OFF Schematic Tractor - Model Number WE16542EElectrical 2122178437 178861Chassis and Enclosures 174620 17490608Drive 175765 175456175578 179114Steering Assembly 175121 177876175146 175118Optional Equipment Spark Arrester170551 Control Throt/Ch Lh Seat Assembly Decals Wheels & Tires180530 180531Mower Lift 175689 Mower Deck 143 159 144 150174493 173984178342 179292Service Notes Limited Warranty C U M SEH Suggested Guide for Sighting Slopes for Safe Operation

180530 specifications

The Weed Eater 180530 is a powerful and efficient string trimmer designed to make yard maintenance easier and more effective. With its robust features and modern technology, this tool stands out as a reliable choice for both amateur gardeners and professional landscapers.

One of the main features of the 180530 is its lightweight design, allowing for easy maneuverability and reduced user fatigue during extended use. Weighing in at just around 8 pounds, it is easy to handle, making it suitable for users of all experience levels.

Powering the Weed Eater 180530 is a 25cc 2-cycle engine, which delivers impressive performance and efficiency. This engine provides rapid acceleration and effective cutting capabilities, allowing users to tackle tough weeds and thick grass with ease. The 2-cycle engine design is known for its simplicity and ease of maintenance, ensuring that users can quickly get back to work.

The 180530 features an automatic dual line feed system, which ensures that the cutting line is always at the optimal length during operation. This reduces downtime associated with manual line adjustments, thereby enhancing productivity. The trimmer is equipped with a straight shaft, which extends reach and makes it easier to access difficult areas.

Another standout characteristic of the Weed Eater 180530 is its versatility. This trimmer is designed to accept a variety of attachments, allowing users to switch between functions such as edging, blowing, and cultivating with ease. This adaptability provides excellent value for users who want a multi-functional landscape tool.

Safety is also prioritized in the design of the 180530. It comes with an easy-to-operate throttle control that allows users to manage the power output effectively. Additionally, the protective guard helps to shield the user from debris while operating, enhancing overall safety during use.

In conclusion, the Weed Eater 180530 combines powerful performance with a lightweight and user-friendly design. Its versatile capabilities, efficient engine technology, and safety features make it a valuable addition to any yard care toolkit. Whether tackling a small garden or maintaining larger landscapes, the 180530 is well-equipped to handle a variety of trimming tasks, ensuring beautifully maintained outdoor spaces.
Top Page Image Contents