Weed Eater 179347 owner manual HOW to USE Your Tractor

Page 11

OPERATION

The operation of any tractor can result in foreign objects thrown into the eyes, which can result in severe eye damage. Always wear safety glasses or eye shields while operating your tractor or performing any adjustments or repairs. We recommend a wide vision safety mask over spectacles or standard safety glasses.

HOW TO USE YOUR TRACTOR

TO SET PARKING BRAKE (See Fig. 5)

Your tractor is equipped with an operator presence sensing switch. When engine is running, any attempt by the operator to leave the seat without first setting the parking brake will shut off the engine.

•Depress clutch/brake pedal into full “BRAKE” position and hold.

•Place parking brake lever in “ENGAGED” position and release pressure from clutch/brake pedal. Pedal should remain in “BRAKE” position. Make sure parking brake will hold tractor secure.

 

ATTACHMENT CLUTCH

 

LEVER "ENGAGED"

THROTTLE/CHOKE

POSITION

CONTROL

IGNITION

 

 

KEY

 

"DISENGAGED"

 

POSITION

 

PARKING BRAKE

"BRAKE"

"ENGAGED"

POSITION

POSITION

 

MOTION

 

CONTROL

 

LEVER

CLUTCH/BRAKE PEDAL

PARKING BRAKE

"DRIVE" POSITION

"DISENGAGED" POSITION

FIG. 5

STOPPING (See Fig. 5)

MOWER BLADES -

•To stop mower blades,move attachment clutch lever to “DISENGAGED” position.

GROUND DRIVE -

•To stop ground drive, depress clutch/brake pedal into full “BRAKE” position.

•Move motion control lever to neutral (N) position.

IMPORTANT: THE MOTION CONTROL LEVER DOES NOT RETURN TO NEUTRAL (N) POSITION WHEN THE CLUTCH/BRAKE PEDAL IS DEPRESSED.

ENGINE -

•Move throttle control to slow position.

NOTE: Failure to move throttle control to slow position and allowing engine to idle before stopping may cause engine to “backfire”.

•Turn ignition key to “OFF” position and remove key.

Always remove key when leaving tractor to prevent

 

unauthorized use.

11

•Never use choke to stop engine.

IMPORTANT: LEAVING THE IGNITION SWITCH IN ANY POSITION OTHER THAN "OFF" WILL CAUSE THE BATTERY TO BE DISCHARGED, (DEAD).

NOTE: Under certain conditions when tractor is standing idle with the engine running, hot engine exhaust gases may cause “browning” of grass. To eliminate this possibility, always stop engine when stopping tractor on grass areas.

CAUTION: Always stop tractor com- pletely, as described above, before leav- ing the operator's position; to empty grass catcher, etc.

TO USE THROTTLE CONTROL (See Fig. 5)

Always operate engine at full throttle.

•Operating engine at less than full throttle reduces the battery charging rate.

•Full throttle offers the best bagging and mower perfor- mance.

TO MOVE FORWARD AND BACKWARD (See Fig. 5)

The direction and speed of movement is controlled by the motion control lever.

•Start tractor with motion control lever in neutral (N) position.

•Release parking brake and clutch/brake pedal.

•Slowly move motion control lever to desired position.

TO ADJUST MOWER CUTTING HEIGHT (See Fig. 5)

The position of the attachment lift lever determines the cutting height.

•Grasp lift lever.

•Press plunger with thumb and move lever to desired position.

The cutting height range is approximately 1-1/2 to 4". The heights are measured from the ground to the blade tip with the engine not running. These heights are approximate and may vary depending upon soil conditions, height of grass and types of grass being mowed.

•The average lawn should be cut to approximately 2-1/2 inches during the cool season and to over 3 inches during hot months. For healthier and better looking lawns, mow often and after moderate growth.

•For best cutting performance, grass over 6 inches in height should be mowed twice. Make the first cut relatively high; the second to desired height.

Page 10 Page 12
Image 11
Page 10 Page 12
Contents Model NO. S165H42D II. Slope Operation IV. ServiceSafe Operation Practices for Ride-On Mowers General OperationTable of Contents Customer Responsibilities Product SpecificationsSlope Sheet Unassembled PartsSteering Wheel Seat To Remove Tractor from CAR- TON AssemblyTools Required for Assembly HOW to SET UP Your TractorLower seat into operating position and sit on seat Install Seat See FigCheck Brake System Check Tire PressureCheck Deck Levelness Check for Proper Position of ALL BeltsOperation Know Your Tractor HOW to USE Your Tractor To Transport See Figs To Adjust Gauge Wheels See FigTo Operate Mower See Fig To Operate on HillsTo Start Engine See Fig Before Starting the EngineCheck Engine OIL Level ADD GasolineMowing Tips Before Each USE Customer ResponsibilitiesGeneral Recommendations Tractor Engine Spark Plugs CleaningAIR Filter MufflerTo Remove Mower See Fig Service and AdjustmentsTo Install Mower See Fig To Level Mower HousingBelt Removal To Adjust Brake See FigBelt Installation To Replace Mower Blade Drive Belt See FigTo Replace Motion Drive Belt See Fig Transaxle Motion Control Lever Neutral Adjustment See FigTransmission REMOVAL/REPLACEMENT To Adjust Steering Wheel AlignmentTo Attach Jumper Cables To Start Engine with a Weak Battery See FigReplacing Battery See Figs To Remove Wheel for Repairs See FigTo Replace Fuse To Adjust CarburetorTo Replace Headlight Bulb Interlocks and RelaysEngine OIL StorageOther Fuel SystemTroubleshooting Points When operator leaves Tractor - Model Number S165H42D SchematicElectrical KEY Part NO. NO. Description Chassis and Enclosures KEY Part Description Drive 178140 Steering Assembly KEY Part NO. NO. Description Optional Equipment EngineMower Lift Seat Assembly Wheels & Tires DecalsMower Deck 179292 Limited Warranty Suggested Guide for Sighting Slopes for Safe Operation

179347 specifications

The Weed Eater 179347 is a versatile tool designed for efficient yard maintenance, catering to both residential and professional users. This string trimmer boasts a powerful engine that provides the reliability needed for tackling tough grass and weeds, making it an essential addition to any landscaping arsenal.

One of the standout features of the Weed Eater 179347 is its lightweight design. Weighing in at just over 10 pounds, it allows users to maneuver easily around their lawns, gardens, and other landscape areas without undue fatigue. The balanced build ensures comfortable handling, which is crucial for extended use during large trimming jobs.

The Weed Eater 179347 is equipped with a dependable 2-cycle engine that delivers impressive power and performance. This engine type not only enhances operational strength but also ensures faster cutting speeds, making it easier to handle dense growth. The trimmer uses a Tap 'N Go line release system that allows users to feed more line simply by tapping the trimmer head on the ground, which adds convenience and keeps the workflow steady.

Another key characteristic of the 179347 model is its adjustable handle. Users can customize the handle height and angle to suit their preferences, improving comfort and efficiency while working on various types of terrain. This flexibility is particularly beneficial for those with larger yards or varied landscaping features.

The design also includes a protective shield that keeps debris from flying towards the user, enhancing safety during operation. The trimmer’s durable construction ensures it can withstand the rigors of frequent use while maintaining its effectiveness.

In terms of technology, the Weed Eater 179347 incorporates fuel-efficient technology that minimizes emissions while providing optimal power output. This eco-friendly feature appeals to environmentally conscious users who wish to reduce their carbon footprint while maintaining their lawns.

In summary, the Weed Eater 179347 combines power, comfort, and convenience, making it an excellent choice for anyone looking to maintain their outdoor spaces effectively. With its lightweight build, powerful engine, adjustable handle, and user-friendly line feed system, this trimmer is designed to meet the demands of both casual users and professional landscapers alike, ensuring beautifully manicured lawns with ease.
Top Page Image Contents