Weed Eater 179347 owner manual To Replace Mower Blade Drive Belt See Fig, To Adjust Brake See Fig

Page 20

SERVICE AND ADJUSTMENTS

NOTE: Three full turns of adjustment nut will change mower height about 1/8".

•Recheck measurements after adjusting.

BOTTOM EDGE

 

BOTTOM EDGE

OF MOWER

 

OF MOWER

TO GROUND

 

TO GROUND

“A”

GROUND LINE

“A”

FIG. 17

SUSPENSION ARM

LIFT LINK ADJUSTMENT NUT

FIG. 18

FRONT-TO-BACK ADJUSTMENT (See Figs. 19 and 20)

IMPORTANT: DECK MUST BE LEVEL SIDE-TO-SIDE. IF THE FOLLOWING FRONT-TO-BACK ADJUSTMENT IS NECESSARY, BE SURE TO ADJUST BOTH FRONT LINKS EQUALLY SO MOWER WILL STAY LEVEL SIDE-TO- SIDE.

To obtain the best cutting results, the mower housing should be adjusted so that the front is approximately 1/8" to 1/2" lower than the rear when the mower is in its highest position.

Check adjustment on right side of tractor. Measure distance “D” directly in front and behind the mandrel at bottom edge of mower housing as shown.

•Before making any necessary adjustments, check that both front links are equal in length. Both links should be approximately 10-3/8".

•If links are not equal in length, adjust one link to same length as other link.

•To lower front of mower loosen nut “E” on both front links an equal number of turns.

•When distance “D” is 1/8" to 1/2" lower at front than rear, tighten nuts “F” against trunnion on both front links.

•To raise front of mower, loosen nut “F” from trunnion on both front links. Tighten nut “E” on both front links an equal number of turns.

•When distance “D” is 1/8" to 1/2" lower at front than rear, tighten nut “F” against trunnion on both front links.

•Recheck side-to-side adjustment.

MANDREL

"D"

"D"

FIG. 19

BOTH FRONT LINKS MUST BE EQUAL IN LENGTH

NUT "E"

NUT "F"

TRUNNION

FRONT LINKS

FIG. 20

TO REPLACE MOWER BLADE DRIVE BELT (See Fig. 21)

The mower blade drive belt may be replaced without tools. Park the tractor on level surface. Engage parking brake.

BELT REMOVAL -

•Remove mower from tractor (See “TO REMOVE MOWER” in this section of this manual).

•Work belt off both mandrel pulleys and idler pulleys.

•Pull belt away from mower.

BELT INSTALLATION -

•Install new belt in reverse order of removal.

•Make sure belt is in all pulley grooves and inside all belt guides.

•Install mower in reverse order of removal instructions.

MANDREL PULLEY IDLER PULLEYS

MANDREL

PULLEY

FIG. 21

TO ADJUST BRAKE (See Fig. 22)

Your tractor is equipped with an adjustable brake system which is mounted on the side of the transaxle.

If tractor requires more than six (6) feet stopping distance at high speed in highest gear on a level dry concrete or paved surface, then brake must be adjusted.

20

Page 19 Page 21
Image 20
Page 19 Page 21
Contents Model NO. S165H42D IV. Service Safe Operation Practices for Ride-On MowersGeneral Operation II. Slope OperationTable of Contents Product Specifications Customer ResponsibilitiesSlope Sheet Unassembled PartsSteering Wheel Seat Assembly Tools Required for AssemblyHOW to SET UP Your Tractor To Remove Tractor from CAR- TONInstall Seat See Fig Lower seat into operating position and sit on seatCheck Tire Pressure Check Deck LevelnessCheck for Proper Position of ALL Belts Check Brake SystemOperation Know Your Tractor HOW to USE Your Tractor To Adjust Gauge Wheels See Fig To Operate Mower See FigTo Operate on Hills To Transport See FigsBefore Starting the Engine Check Engine OIL LevelADD Gasoline To Start Engine See FigMowing Tips Before Each USE Customer ResponsibilitiesGeneral Recommendations Tractor Engine Cleaning AIR FilterMuffler Spark PlugsService and Adjustments To Install Mower See FigTo Level Mower Housing To Remove Mower See FigTo Adjust Brake See Fig Belt InstallationTo Replace Mower Blade Drive Belt See Fig Belt RemovalTransaxle Motion Control Lever Neutral Adjustment See Fig Transmission REMOVAL/REPLACEMENTTo Adjust Steering Wheel Alignment To Replace Motion Drive Belt See FigTo Start Engine with a Weak Battery See Fig Replacing Battery See FigsTo Remove Wheel for Repairs See Fig To Attach Jumper CablesTo Adjust Carburetor To Replace Headlight BulbInterlocks and Relays To Replace FuseStorage OtherFuel System Engine OILTroubleshooting Points When operator leaves Schematic Tractor - Model Number S165H42DElectrical KEY Part NO. NO. Description Chassis and Enclosures KEY Part Description Drive 178140 Steering Assembly KEY Part NO. NO. Description Engine Optional EquipmentMower Lift Seat Assembly Decals Wheels & TiresMower Deck 179292 Limited Warranty Suggested Guide for Sighting Slopes for Safe Operation

179347 specifications

The Weed Eater 179347 is a versatile tool designed for efficient yard maintenance, catering to both residential and professional users. This string trimmer boasts a powerful engine that provides the reliability needed for tackling tough grass and weeds, making it an essential addition to any landscaping arsenal.

One of the standout features of the Weed Eater 179347 is its lightweight design. Weighing in at just over 10 pounds, it allows users to maneuver easily around their lawns, gardens, and other landscape areas without undue fatigue. The balanced build ensures comfortable handling, which is crucial for extended use during large trimming jobs.

The Weed Eater 179347 is equipped with a dependable 2-cycle engine that delivers impressive power and performance. This engine type not only enhances operational strength but also ensures faster cutting speeds, making it easier to handle dense growth. The trimmer uses a Tap 'N Go line release system that allows users to feed more line simply by tapping the trimmer head on the ground, which adds convenience and keeps the workflow steady.

Another key characteristic of the 179347 model is its adjustable handle. Users can customize the handle height and angle to suit their preferences, improving comfort and efficiency while working on various types of terrain. This flexibility is particularly beneficial for those with larger yards or varied landscaping features.

The design also includes a protective shield that keeps debris from flying towards the user, enhancing safety during operation. The trimmer’s durable construction ensures it can withstand the rigors of frequent use while maintaining its effectiveness.

In terms of technology, the Weed Eater 179347 incorporates fuel-efficient technology that minimizes emissions while providing optimal power output. This eco-friendly feature appeals to environmentally conscious users who wish to reduce their carbon footprint while maintaining their lawns.

In summary, the Weed Eater 179347 combines power, comfort, and convenience, making it an excellent choice for anyone looking to maintain their outdoor spaces effectively. With its lightweight build, powerful engine, adjustable handle, and user-friendly line feed system, this trimmer is designed to meet the demands of both casual users and professional landscapers alike, ensuring beautifully manicured lawns with ease.
Top Page Image Contents