Weed Eater 530087644 Restarting a Warm Engine, Operating Position, Advancing the Cutting Line

Page 4

SSqueeze the throttle trigger fully and hold

through all remaining steps.

SPull starter rope handle sharply 6 times. S Move choke lever to HALF CHOKE posi-

tion.

S Pull starter rope handle no more than 6

pulls, until engine runs.

S Allowenginetorun10seconds,thenmove choke lever to OFF CHOKE position.

RESTARTING A WARM ENGINE

SMovechokelever toOFF CHOKEposition. S Pull starter rope handle until engine runs. S If engine does not start in 5 pulls, follow instructions in STARTING A COLD EN-

GINE.

OPERATING POSITION

ALWAYS WEAR:

Eye Protectio

Long Pants

Heavy Shoes

Cut from your right to your left.

ADVANCING THE CUTTING LINE

Advancelineby tappingthebottomofthecut- tingheadlightly onthe groundwhile engineis running at full speed. The metal line limiter blade attached to the shieldwill cutthe lineto the proper length.

REPLACING THE LINE

SPushandholdtheenginestopswitch inthe stop/off position until the unit has fully stopped.

SDisconnect the spark plug lead wire.

SRemove spool by firmly pulling on tapbut-

ton.

SClean entire surface of hub and spool.

SReplacewithapre-woundspool,or cuttwo

lengths of12-1/2feetof.080” (2 mm) diam- eter Weed Eater r brand line. Never use wire,rope,string,etc., whichcan break off

and become a dangerous missile.

SInsertends ofthelineabout 1/2inch (1cm) into the small hole on the inside of spool.

Spool

Small

Holes

Line exit holes

Line in Notch

Line in Notch

Hub

SWind the line evenly and tightly onto the spool. Wind in the direction of the arrows found on the spool.

SPushthelineintothenotches,leaving3to5 inches (7 - 12 cm) unwound.

SInsert the line into the the exit holes in the hub as shown in the illustration.

SAlign the notches with the line exit hole.

S Pushspoolintohubuntilitsnaps intoplace. S Pull the line extendingoutside ofthe hubto

release it from the notch.

Werecommend allservice andadjustments not listed in this manual be performed by an Authorized Service Dealer.

TROUBLESHOOTING CHART

Engine will not start.

SFuel tank empty.

S Engine flooded.

S Spark plug not firing.

S Fuel not reaching carburetor.

S Carburetor requires adjustment.

Engine will not idle properly.

SCarburetor requires adjustment. S Throttle trigger screw too tight.

Engine will not accelerate, lacks power, or dies under a load.

SAir filter dirty.

SSpark plug fouled.

SCarburetor requires adjustment.

Engine smokes excessively.

SAir filter dirty.

SToo much oil mixed with gasoline. S Carburetor requires adjustment.

Line does not advance or breaks while cutting.

SLine improperly routed in head.

S Line improperly wound on spool. S Line size incorrect.

Line welds onto spool.

SLine size incorrect

SLine improperly wound on spool.

SCrowding line on material being cut.

Line pulls back into head

S Too little line outside of head. S Line size incorrect.

4

Image 4
Contents Please do not return unit to retailer English Español FrançaisWCI Outdoor Products, Inc Operator Safety Unit / Maintenance SafetyFuel Safety Cutting SafetyHOW to Stop Your Unit Adjust the HandleCold Engine Starting or Starting After Refueling Troubleshooting Chart Restarting a Warm EngineOperating Position Advancing the Cutting LineWarranty Statement Carburetor AdjustmentsIgnition Timing Spark PlugMAINTENANCE,REPLACEMENTANDRE- PAIROFEMISSIONRELATEDPARTSAny Not covered. ADD-ON or Modified

530087644 specifications

The Weed Eater 530087644 is a well-regarded tool in the realm of outdoor maintenance, specifically designed for homeowners and gardening enthusiasts who require an efficient and reliable solution for tackling overgrown lawns and wild areas. This versatile string trimmer boasts a blend of power, precision, and durability that allows users to quickly and effectively trim grass, weeds, and underbrush.

One of the standout features of the Weed Eater 530087644 is its lightweight design. Weighing in at just a few pounds, it is easy to maneuver, reducing fatigue during extended use. This makes it an ideal choice for those who may find heavier trimmers cumbersome. The ergonomic handle further enhances comfort, allowing users to grip the tool securely while navigating around obstacles in their yard.

A significant technological aspect of the Weed Eater 530087644 is its reliable gas-powered engine. This engine provides ample power, ensuring that users can tackle thick grass and tough weeds without bogging down. The engine’s robust design is engineered for efficiency, offering a good balance of power and fuel consumption. This feature is particularly advantageous for larger yards where electric models may struggle or require frequent recharging.

The trimming head of the Weed Eater 530087644 is equipped with a dual-line system, which enhances cutting performance. This system allows for a wider cutting path, enabling users to cover more ground in less time. Additionally, the automatic line advancement feature ensures that the trimmer feeds line as needed, minimizing downtime and increasing productivity.

The Weed Eater 530087644 also emphasizes user safety and maintenance simplicity. It comes with a clear instruction manual and features that make starting and stopping the engine straightforward. The easy access to the air filter and spark plug allows for efficient routine maintenance, helping to prolong the life of the trimmer.

Built to withstand the rigors of outdoor use, the sturdy construction of the Weed Eater 530087644 ensures reliability and longevity. The durable materials used in its design safeguard against wear and tear, making this tool a worthy investment for any homeowner looking to maintain their outdoor spaces effectively.

In summary, the Weed Eater 530087644 combines a lightweight design, powerful gas engine, user-friendly features, and robust construction, making it an excellent choice for lawn care enthusiasts. Whether you're dealing with simple grass trimming or tackling tougher terrain, this tool is equipped to handle various tasks with ease and efficiency.