HOW to Start Your Unit, Operating Position

Engine Choke Lever

ON/STOP

Switch

FULL HALF OFF

HOW TO START YOUR UNIT

WARNING: The trimmer head will turn while starting the engine. Avoid any con- tact with the muffler. A hot muffler can cause serious burns.

STARTING A COLD ENGINE (or a warm engine after running out of fuel)

Starting Position

1.Set unit on a flat surface.

2.Slowly press the primer bulb 6 times.

3.Move choke lever to the FULL CHOKE position.

4.Squeeze the throttle trigger fully and hold through all remaining steps.

Starter Handle

Choke

Lever

Muffler

Primer Bulb

5.Pull starter rope handle sharply until engine sounds as if it is trying to start, but do not pull rope more than 6 times.

6.As soon as engine sounds as if it is trying to start, move choke lever to HALF CHOKE position.

7.Pull starter rope sharply until engine runs, but no more than 6 pulls.

NOTE: If the engine doesn’t start after 6 pulls (at the HALF CHOKE position), move the choke lever to the FULL CHOKE position and press the primer bulb 6 times. Squeeze and hold the throttle trigger and pull the starter rope 2 more times. Move the choke lever to the HALF CHOKE position and pull the start- er rope until the engine runs, but no more than 6 pulls. If the engine still doesn’t start, it is probably flooded. Proceed to

STARTING A FLOODED ENGINE.

8.Once the engine starts, allow it to run 10 seconds, then move the choke lever to the OFF CHOKE position. Allow the unit

to run for 30 more seconds at OFF CHOKE before releasing the throttle trig- ger.

NOTE: If engine dies with the choke le- ver in the OFF CHOKE position, move the choke lever to the HALF CHOKE position and pull the rope until engine runs, but no more than 6 pulls.

STARTING A WARM ENGINE

1.Move the choke lever to the HALF CHOKE position.

2.Squeeze and hold the throttle trigger. Keep throttle trigger fully squeezed until the engine runs smoothly.

3.Pull starter rope sharply until engine runs, but no more than 5 pulls.

4.Allow engine to run 15 seconds, then move the choke lever to the OFF CHOKE position.

NOTE: If engine has not started, pull start- er rope 5 more pulls. If engine still does not run, it is probably flooded.

STARTING A FLOODED ENGINE

Flooded engines can be started by placing the choke lever in the OFF CHOKE position; then, pull the rope to clear the engine of ex- cess fuel. This could require pulling the starter handle many times depending on how badly the unit is flooded.

If the unit still doesn’t start, refer to TROUBLESHOOTING TABLE or call 1-800-554--6723.

OPERATING POSITION

Cut from your left to your right.

WARNING: Always wear eye protec- tion. Never lean over the trimmer head. Rocks or debris can ricochet or be thrown into eyes and face and cause blindness or other serious injury.

Do not run the engine at a higher speed than necessary. The cutting line will cut efficiently when the engine is run at less than full throttle. At lower speeds, there is less engine noise and vibration. The cutting line will last longer and will be less likely to “weld” onto the spool.

Always release the throttle trigger and allow the engine to return to idle speed when not cutting.

To stop engine:

S Release the throttle trigger.

530086928 specifications

The Weed Eater 530086928 is an exceptional tool that stands out in the world of lawn care equipment. Designed for both casual gardeners and professional landscapers, this gas-powered string trimmer combines power with versatility, making it a reliable choice for various outdoor tasks.

One of the main features of the Weed Eater 530086928 is its robust 25cc engine, which delivers ample power to efficiently tackle tough weeds and overgrown grass. The lightweight design, at just under 10 pounds, allows for easy maneuverability, reducing user fatigue during extended use. This makes it ideal for users looking to maintain their lawns without the strain that heavier models may impose.

Another key characteristic of the Weed Eater 530086928 is its adjustable cutting head. This feature allows users to easily switch between different angles for optimal trimming, ensuring that hard-to-reach areas are effectively addressed. Additionally, the cutting width of up to 17 inches enables faster trimming, allowing users to cover more ground in less time.

The dual-line system that the Weed Eater 530086928 employs is another standout technology. This system ensures that the trimmer utilizes two lines of nylon string, creating a cleaner and more efficient cut. The bump feed mechanism simplifies line advancement, allowing users to easily extend the cutting line without stopping the engine — a feature particularly appreciated during extensive gardening projects.

Durability is also at the forefront of the Weed Eater 530086928's design. The trimmer features high-quality materials and components designed to withstand the rigors of regular use. Coupled with a user-friendly starting system, this machine is manageable for individuals of varying experience levels.

Furthermore, the ergonomic handle design provides comfortable grip and control, enabling users to navigate complex lawns while maintaining accuracy. The inclusion of anti-vibration technology contributes to the overall user experience, diminishing the harsh impacts of vibration on the hands and arms.

In summary, the Weed Eater 530086928 delivers a powerful, efficient, and user-friendly experience for all lawn care enthusiasts. With a combination of a powerful engine, adjustable cutting head, dual-line system, and ergonomic design, it has cemented its place as a dependable choice for tackling any trimming task with ease and precision.