Replacing the Line, Carburetor Adjustment

REPLACING THE LINE

1.Remove spool by firmly pulling on tap button.

2.Clean entire surface of hub and spool.

3.Replace with a pre-wound spool, or cut two lengths of 12-1/2feet of 0.080! (2 mm) di- ameter Weed Eaterr brand line.

WARNING: Never use wire, rope, string, etc., which can break off and become a dangerous missile.

4.Insert ends of the lines about 1/2 inch (1 cm) into the small holes on the inside of spool.

Spool

Small

Holes

Line exit holes					Line in Notch

Line in Notch

Hub

5.Wind the line evenly and tightly onto the spool. Wind in the direction of the arrows found on the spool.

6.Push the lines into the notches, leaving 3 to 5 inches (7 -- 12 cm) unwound.

7.Insert the lines into the the exit holes in the hub as shown in the illustration.

8.Align the notches with the line exit holes.

9.Push spool into hub until it snaps into place.

10.Pull the lines extending outside of the hub to release the lines from the notches.

REPLACING THE CUTTING HEAD

1.Push in locking lever and hold.

2.Rotate dust cup until the locking lever falls into one of the grooves.

Locking Lever

3.Continue to hold in locking lever. This will prevent the shaft from turning while re- moving and installing trimmer head.

4.Remove trimmer head by turning clock- wise.

5.Thread replacement trimmer head onto the shaft by turning counterclockwise. Tighten until secure.

6.Release locking lever.

CARBURETOR ADJUSTMENT

Your carburetor is equipped with limiter caps. Carburetor adjustment is a complicated task. We recommend that you take your unit to an au- thorized service dealer. Damage will occur if you turn the needles beyond the limiter stops.

WARNING: Perform the following steps after each use:

SAllow engine to cool before storing or trans-

porting.

SStore unit and fuel in a well ventilated area where fuel vapors cannot reach sparks or open flames from water heaters, electric motors or switches, furnaces, etc.

SStore unit with all guards in place. Position

unit so that any sharp object cannot acci- dentally cause injury.

SStore unit and fuel well out of the reach of children.

SEASONAL STORAGE

Prepare unit for storage at end of season or if it will not be used for 30 days or more.

If your unit is to be stored for a period of time: S Clean the entire unit before lengthy

storage.

SStore in a clean dry area.

S Lightly oil external metal surfaces.

FUEL SYSTEM

Under FUELING ENGINE in the OPERA- TION section of this manual, see message la- beled IMPORTANT regarding the use of ga- sohol in your engine.

Fuel stabilizer is an acceptable alternative in minimizing the formation of fuel gum deposits during storage. Add stabilizer to the gasoline in the fuel tank or fuel storage container. Fol- low the mix instructions found on stabilizer container. Run engine at least 5 minutes after adding stabilizer.

ENGINE

SRemove spark plug and pour 1 teaspoon of 40:1, 2-cycle engine oil (air cooled) through

the spark plug opening. Slowly pull the starter rope 8 to 10 times to distribute oil.

SReplace spark plug with new one of recom- mended type and heat range.

SClean air filter.

S Check entire unit for loose screws, nuts, and bolts. Replace any damaged, broken, or worn parts.

530086928 specifications

The Weed Eater 530086928 is an exceptional tool that stands out in the world of lawn care equipment. Designed for both casual gardeners and professional landscapers, this gas-powered string trimmer combines power with versatility, making it a reliable choice for various outdoor tasks.

One of the main features of the Weed Eater 530086928 is its robust 25cc engine, which delivers ample power to efficiently tackle tough weeds and overgrown grass. The lightweight design, at just under 10 pounds, allows for easy maneuverability, reducing user fatigue during extended use. This makes it ideal for users looking to maintain their lawns without the strain that heavier models may impose.

Another key characteristic of the Weed Eater 530086928 is its adjustable cutting head. This feature allows users to easily switch between different angles for optimal trimming, ensuring that hard-to-reach areas are effectively addressed. Additionally, the cutting width of up to 17 inches enables faster trimming, allowing users to cover more ground in less time.

The dual-line system that the Weed Eater 530086928 employs is another standout technology. This system ensures that the trimmer utilizes two lines of nylon string, creating a cleaner and more efficient cut. The bump feed mechanism simplifies line advancement, allowing users to easily extend the cutting line without stopping the engine — a feature particularly appreciated during extensive gardening projects.

Durability is also at the forefront of the Weed Eater 530086928's design. The trimmer features high-quality materials and components designed to withstand the rigors of regular use. Coupled with a user-friendly starting system, this machine is manageable for individuals of varying experience levels.

Furthermore, the ergonomic handle design provides comfortable grip and control, enabling users to navigate complex lawns while maintaining accuracy. The inclusion of anti-vibration technology contributes to the overall user experience, diminishing the harsh impacts of vibration on the hands and arms.

In summary, the Weed Eater 530086928 delivers a powerful, efficient, and user-friendly experience for all lawn care enthusiasts. With a combination of a powerful engine, adjustable cutting head, dual-line system, and ergonomic design, it has cemented its place as a dependable choice for tackling any trimming task with ease and precision.