McCulloch MC1136 Tools Required for Assembly, To Remove Tractor from Carton, Unpack Carton

Page 6

ASSEMBLY

Your new tractor has been assembled at the factory with exception of those parts left unassembled for shipping purposes. To ensure safe and proper operation of your tractor all parts and hardware you assemble must be tightened securely. Use the correct tools as necessary to insure proper tightness.

TOOLS REQUIRED FOR ASSEMBLY

A socket wrench set will make assembly easier. Standard wrench sizes are listed.

(2)

7/16" wrenches

Pliers

(1)

3/4" wrench

Tire pressure gauge

Utility knife

When right or left hand is mentioned in this manual, it means when you are in the operating position (seated behind the steering wheel).

TO REMOVE TRACTOR FROM CARTON

UNPACK CARTON

•Remove all accessible loose parts and parts cartons from carton.

•Cut along dotted lines on all four panels of carton. Remove end panels and lay side panels flat.

•Check for any additional loose parts or cartons and remove.

STEERING

WHEEL

ADAPTER

1/4 LOCKNUT

INSERT

1/2 HEX NUT

LARGE FLAT

WASHER

STEERING

BOOT

TABS

EXTENSION SHAFT

1/4 HEX BOLT

BEFORE REMOVING TRACTOR FROM SKID

ATTACH STEERING WHEEL (See Fig. 1)

ASSEMBLE EXTENSION SHAFT AND BOOT

•Slide extension shaft onto lower steering shaft. Align mounting holes in extension and lower shafts and install 1/4 hex bolt and locknut. Tighten securely.

IMPORTANT: TIGHTEN BOLT AND NUT SECURELY TO 10-12 FT. LBS TORQUE.

•Place tabs of steering boot over tab slots in dash and push down to secure.

INSTALL STEERING WHEEL

•Position front wheels of the tractor so they are pointing straight forward.

•Remove steering wheel adapter from steering wheel and slide adapter onto steering shaft extension.

•Position steering wheel so cross bars are horizontal (left to right) and slide inside boot and onto adapter.

•Assemble large flat washer, 1/2 hex nut and tighten securely.

•Snap steering wheel insert into center of steering wheel.

•Remove protective materials from tractor hood and grill.

IMPORTANT: CHECK FOR AND REMOVE ANY STAPLES IN SKID THAT MAY PUNCTURE TIRES WHERE TRACTOR IS TO ROLL OFF SKID.

LOWER

STEERING

SHAFT

FIG. 1

TAB SLOTS

6

Page 5 Page 7
Image 6
Page 5 Page 7
Contents Model NO. MC1136 MC1136B 11 HP 36 Inch Lawn Tractor General Operation Safety RulesSafe Operation Practices for Ride-On Mowers II. Slope OperationService III. ChildrenIV. Towing Table of Contents Unassembled Parts Steering Wheel SeatTo Remove Tractor from Carton AssemblyTools Required for Assembly Before Removing Tractor from SkidHOW to SET UP Your Tractor Install Seat See FigCheck Battery See Fig Check for Proper Position of ALL Belts Check Tire PressureCheck Deck Levelness Check Brake SystemOperation Know Your Tractor HOW to USE Your Tractor Before Starting the Engine Mowing Tips To Start Engine See FigMaintenance General RecommendationsBefore Each USE Tires TractorBrake Operation Operator Presence SystemEngine Muffler CleaningAIR Filter See Fig Spark PlugsService and Adjustments To Install Mower see FIGTo Remove Mower See Fig To Level Mower Housing FRONT-TO-BACK Adjustment See FigsTo Check and Adjust Brake See Fig To Replace Mower Blade Drive Belt See FigFront Wheel TOE-IN/CAMBER To Adjust Steering Wheel ALIGN- MentTo Replace Motion Drive Belt See Fig To Remove Wheel for Repairs See FigTo Start Engine with a Weak Battery See Fig Replacing Battery See FigsInterlocks and Relays To Remove Hood and Grill Assembly See FigTo Adjust Carburetor To Replace FuseFuel System StorageOther Engine OILTroubleshooting Points When operator leaves seat Repair Parts SchematicElectrical KEY Part NO. NO. Description Chassis and Enclosures 532 19 39-34 Dash Drive Repair Parts Steering Repair Parts Engine Optional EquipmentSeat Decals Wheels & TiresMower Lift Mower Deck KEY Part Description Policy Suggested Guide for Sighting Slopes for Safe Operation Only Ride UP and Down Hill Not Across Hill Degrees MAX
Top Page Image Contents