McCulloch 422800 manual Tractor, Blade Removal See Fig, Battery

Page 16

MAINTENANCE

TRACTOR

Always observe safety rules when performing any main- tenance.

BRAKE OPERATION

If tractor requires more than five (5) feet to stop at highest speed in highest gear on a level, dry concrete or paved surface, then brake must be checked and adjusted. (See “TO ADJUST BRAKE” in the Service and Adjustments section of this manual).

TIRES

•Maintain proper air pressure in all tires (See “PRODUCT SPECIFICATIONS” section of this manual).

•Keep tires free of gasoline, oil, or insect control chemi- cals which can harm rubber.

•Avoid stumps, stones, deep ruts, sharp objects and other hazards that may cause tire damage.

NOTE: To seal tire punctures and prevent flat tires due to slow leaks, tire sealant may be purchased from your local parts dealer. Tire sealant also prevents tire dry rot and corrosion.

OPERATOR PRESENCE SYSTEM AND REVERSE OP- ERATION SYSTEM (ROS)

Be sure operator presence and reverse operation systems are working properly. If your tractor does not function as described, repair the problem immediately.

•The engine should not start unless the brake pedal is fully depressed, and the attachment clutch control is in the disengaged position.

CHECK OPERATOR PRESENCE SYSTEM

•When the engine is running, any attempt by the operator to leave the seat without first setting the parking brake should shut off the engine.

•When the engine is running and the attachment clutch is engaged, any attempt by the operator to leave the seat should shut off the engine.

•The attachment clutch should never operate unless the operator is in the seat.

CHECK REVERSE OPERATION (ROS) SYSTEM

•When the engine is running with the ignition switch in the engine "ON" position and the attachment clutch engaged, any attempt by the operator to shift into reverse should shut off the engine.

ROS "ON" POSITION

ENGINE "ON" POSITION

 

(NORMAL OPERATING)

828

•When the engine is running with the ignition switch in the ROS "ON" position and the attachment clutch en- gaged, any attempt by the operator to shift into reverse should NOT shut off the engine.

BLADE CARE

For best results mower blades must be kept sharp. Replace bent or damaged blades.

CAUTION: Useonlyareplacementblade approved by the manufacturer of your tractor. Using a blade not approved by the manufacturer of your tractor is hazardous, could damage your tractor and void your warranty.

BLADE REMOVAL (See Fig. 12)

•Raise mower to highest position to allow access to blades.

NOTE: Protect your hands with gloves and/or wrap blade with heavy cloth.

•Remove blade bolt by turning counterclockwise.

•Install new or resharpened blade with stamped "THIS SIDE UP" facing deck and mandrel assembly.

IMPORTANT:TOENSUREPROPERASSEMBLY,CENTERHOLE IN BLADE MUST ALIGN WITH STAR ON MANDREL ASSEMBLY.

•Install and tighten blade bolt securely (45-55 Ft. Lbs. torque).

IMPORTANT: SPECIAL BLADE BOLT HEAT TREATED.

BLADE

STAR

 

CENTER

 

HOLE

BLADE BOLT

 

(SPECIAL)

 

 

MANDREL

 

ASSEMBLY

FIG. 12

BATTERY

Your tractor has a battery charging system which is sufficient for normal use. However, periodic charging of the battery with an automotive charger will extend its life.

•Keep battery and terminals clean.

•Keep battery bolts tight.

•Keep small vent holes open.

•Recharge at 6-10 amperes for 1 hour.

NOTE: The original equipment battery on your tractor is maintenance free. Do not attempt to open or remove caps or covers. Adding or checking level of electrolyte is not necessary.

TO CLEAN BATTERY AND TERMINALS

Corrosion and dirt on the battery and terminals can cause the battery to “leak” power.

16

Page 15 Page 17
Image 16
Page 15 Page 17
Contents M13538 Always Wear EYE Protection During OperationSafety Rules Safe Operation Practices for Ride-On MowersGeneral Operation II. Slope OperationService General ServiceIII. Children IV. TowingTable of Contents Contents of Hardware Pack Assembly Tools Required for AssemblyToremovetractorfromcarton Before Removing Tractor from SkidInstall Seat See Fig Check Battery See FigCheck Tire Pressure Check Deck LevelnessCheck for Proper Position of ALL Belts Check Brake SystemOperation Know Your Tractor Attachment Clutch Lever Used to engageHOW to USE Your Tractor To SET Parking Brake See FigStopping See Fig To USE Throttle Control D See FigTo Adjust Mower Cutting Height See Fig To Move Forward and Backward See FigTo Operate Mower To Stop Mower BladesBefore Starting the Engine Mowing Tips To Start Engine See FigMaintenance Lubrication ChartTractor BatteryBlade Removal See Fig Engine Cleaning IN-LINE Fuel Filter See FigTo Install Mower See Figs Service and AdjustmentsTo Remove Mower See Fig Install belt on engine pulley M Visual SIDE-TO-SIDE Adjustment See Fig To Level MowerTransaxle Gear Shift Lever Neutral Adjustment See Fig To Adjust Steering Wheel AlignmentTo Replace Mower Blade Drive Belt See Fig To Check BrakeTo Start Engine with a Weak Battery See Fig Replacing Battery See FigTo Remove Wheel for Repairs See Fig To Attach Jumper CablesTo Adjust Throttle Control Cable To Adjust Choke ControlTo Adjust Carburetor To Replace Headlight BulbStorage OtherFuel System Engine OILTroubleshooting Points Problem Cause CorrectionEngine dies when Service Notes Service Notes Service Notes Suggested Guide for Sighting Slopes for Safe Operation

422800 specifications

The McCulloch 422800 is a powerful and versatile chainsaw designed for both professional and recreational woodworkers. Aimed at providing an efficient solution for cutting tasks, this model has garnered attention for its robust features, advanced technologies, and user-friendly design.

One of the standout characteristics of the McCulloch 422800 is its efficiency. It is equipped with a 42cc engine, which delivers a strong performance while ensuring that fuel consumption remains at a reasonable level. This balance of power and efficiency allows users to tackle a variety of cutting tasks, from felling small trees to limb removal and firewood preparation.

A notable feature of the McCulloch 422800 is its lightweight design, making it easy for users to maneuver during operation. Weighing only around 10.5 lbs, this chainsaw reduces user fatigue, enabling longer periods of work without discomfort. The ergonomic handle design further enhances comfort and control, allowing operators to maintain a firm grip even in challenging conditions.

The chainsaw features an automatic oiling system, which ensures that the cutting bar and chain receive the necessary lubrication during operation, enhancing overall performance and extending the lifespan of the components. This system also minimizes the risk of overheating, a common concern for chain saw enthusiasts and professionals alike.

Safety is a priority in the design of the McCulloch 422800, featuring a chain brake that stops the chain in case of kickback, protecting the user from potential injuries. Additionally, the chainsaw is equipped with a throttle lock, which prevents unintentional acceleration, further enhancing safety during use.

Maintenance is straightforward with the McCulloch 422800, as it includes easy access to the air filter and spark plug, simplifying routine checks and servicing. This user-centric design minimizes downtime and ensures that users can keep their chainsaw in optimal working condition.

A powerful, lightweight, and feature-rich tool, the McCulloch 422800 is perfect for both seasoned professionals and casual users interested in reliable performance. Its combination of efficiency, safety features, and ease of maintenance make it an excellent choice for anyone looking to tackle wood cutting tasks with confidence.
Top Page Image Contents