McCulloch 422800 manual Storage, Other, Fuel System, Engine OIL, Cylinders

Page 25

STORAGE

Immediately prepare your tractor for storage at the end of the season or if the tractor will not be used for 30 days or more.

WARNING: Never store the tractor with gasoline in the tank inside a building where fumes may reach an open flame or spark. Allow the engine to cool before storing in any enclosure.

TRACTOR

Remove mower from tractor for winter storage. When mower is to be stored for a period of time, clean it thoroughly, remove all dirt, grease, leaves, etc. Store in a clean, dry area.

•Clean entire tractor (See “CLEANING” in the Mainte- nance section of this manual).

•Inspect and replace belts, if necessary (See belt re- placement instructions in the Service and Adjustments section of this manual).

•Lubricate as shown in the Maintenance section of this manual.

•Be sure that all nuts, bolts and screws are securely fastened. Inspect moving parts for damage, breakage and wear. Replace if necessary.

•Touch up all rusted or chipped paint surfaces; sand lightly before painting.

BATTERY

•Fully charge the battery for storage.

•After a period of time in storage, battery may require recharging.

•To help prevent corrosion and power leakage during long periods of storage, battery cables should be dis- connected and battery cleaned thoroughly (see “TO CLEAN BATTERY AND TERMINALS” in the Mainte- nance section of this manual).

•After cleaning, leave cables disconnected and place cables where they cannot come in contact with battery terminals.

•If battery is removed from tractor for storage, do not store battery directly on concrete or damp surfaces.

ENGINE

FUEL SYSTEM

IMPORTANT: IT IS IMPORTANT TO PREVENT GUM DEPOSITS FROM FORMING IN ESSENTIAL FUEL SYSTEM PARTS SUCH AS CARBURETOR, FUEL FILTER, FUEL HOSE, OR TANK DURING STORAGE. ALSO, EXPERIENCE INDICATES THAT ALCOHOL BLENDED FUELS (CALLED GASOHOL OR USING ETHANOL OR METHANOL) CAN ATTRACT MOISTURE WHICH LEADS TO SEPARATION AND FORMATION OF ACIDS DURING STORAGE. ACIDIC GAS CAN DAMAGE THE FUEL SYSTEM OF AN ENGINE WHILE IN STORAGE.

•Empty the fuel tank by starting the engine and let it run until the fuel lines and carburetor are empty.

•Never use engine or carburetor cleaner products in the fuel tank or permanent damage may occur.

•Use fresh fuel next season.

NOTE: Fuel stabilizer is an acceptable alternative in mini- mizing the formation of fuel gum deposits during storage. Add stabilizer to gasoline in fuel tank or storage container. Always follow the mix ratio found on stabilizer container. Run engine at least 10 minutes after adding stabilizer to allow the stabilizer to reach the carburetor. Do not empty the gas tank and carburetor if using fuel stabilizer.

ENGINE OIL

Drain oil (with engine warm) and replace with clean en- gine oil. (See “ENGINE” in the Maintenance section of this manual).

CYLINDER(S)

•Remove spark plug(s).

•Pour one ounce of oil through spark plug hole(s) into cylinder(s).

•Turn ignition key to “START” position for a few seconds to distribute oil.

•Replace with new spark plug(s).

OTHER

•Do not store gasoline from one season to another.

•Replace your gasoline can if your can starts to rust. Rust and/or dirt in your gasoline will cause problems.

•If possible, store your tractor indoors and cover it to give protection from dust and dirt.

•Cover your tractor with a suitable protective cover that does not retain moisture. Do not use plastic. Plastic cannot breathe which allows condensation to form and will cause your tractor to rust.

IMPORTANT: NEVER COVER TRACTOR WHILE ENGINE AND EXHAUST AREAS ARE STILL WARM.

25

Page 24 Page 26
Image 25
Page 24 Page 26
Contents Always Wear EYE Protection During Operation M13538Safe Operation Practices for Ride-On Mowers Safety RulesGeneral Operation II. Slope OperationGeneral Service ServiceIII. Children IV. TowingTable of Contents Contents of Hardware Pack Tools Required for Assembly AssemblyToremovetractorfromcarton Before Removing Tractor from SkidCheck Battery See Fig Install Seat See FigCheck Deck Levelness Check Tire PressureCheck for Proper Position of ALL Belts Check Brake SystemOperation Attachment Clutch Lever Used to engage Know Your TractorTo SET Parking Brake See Fig HOW to USE Your TractorStopping See Fig To USE Throttle Control D See FigTo Move Forward and Backward See Fig To Adjust Mower Cutting Height See FigTo Operate Mower To Stop Mower BladesBefore Starting the Engine To Start Engine See Fig Mowing TipsLubrication Chart MaintenanceTractor BatteryBlade Removal See Fig Engine IN-LINE Fuel Filter See Fig CleaningTo Install Mower See Figs Service and AdjustmentsTo Remove Mower See Fig Install belt on engine pulley M To Level Mower Visual SIDE-TO-SIDE Adjustment See FigTo Adjust Steering Wheel Alignment Transaxle Gear Shift Lever Neutral Adjustment See FigTo Replace Mower Blade Drive Belt See Fig To Check BrakeReplacing Battery See Fig To Start Engine with a Weak Battery See FigTo Remove Wheel for Repairs See Fig To Attach Jumper CablesTo Adjust Choke Control To Adjust Throttle Control CableTo Adjust Carburetor To Replace Headlight BulbOther StorageFuel System Engine OILProblem Cause Correction Troubleshooting PointsEngine dies when Service Notes Service Notes Service Notes Suggested Guide for Sighting Slopes for Safe Operation

422800 specifications

The McCulloch 422800 is a powerful and versatile chainsaw designed for both professional and recreational woodworkers. Aimed at providing an efficient solution for cutting tasks, this model has garnered attention for its robust features, advanced technologies, and user-friendly design.

One of the standout characteristics of the McCulloch 422800 is its efficiency. It is equipped with a 42cc engine, which delivers a strong performance while ensuring that fuel consumption remains at a reasonable level. This balance of power and efficiency allows users to tackle a variety of cutting tasks, from felling small trees to limb removal and firewood preparation.

A notable feature of the McCulloch 422800 is its lightweight design, making it easy for users to maneuver during operation. Weighing only around 10.5 lbs, this chainsaw reduces user fatigue, enabling longer periods of work without discomfort. The ergonomic handle design further enhances comfort and control, allowing operators to maintain a firm grip even in challenging conditions.

The chainsaw features an automatic oiling system, which ensures that the cutting bar and chain receive the necessary lubrication during operation, enhancing overall performance and extending the lifespan of the components. This system also minimizes the risk of overheating, a common concern for chain saw enthusiasts and professionals alike.

Safety is a priority in the design of the McCulloch 422800, featuring a chain brake that stops the chain in case of kickback, protecting the user from potential injuries. Additionally, the chainsaw is equipped with a throttle lock, which prevents unintentional acceleration, further enhancing safety during use.

Maintenance is straightforward with the McCulloch 422800, as it includes easy access to the air filter and spark plug, simplifying routine checks and servicing. This user-centric design minimizes downtime and ensures that users can keep their chainsaw in optimal working condition.

A powerful, lightweight, and feature-rich tool, the McCulloch 422800 is perfect for both seasoned professionals and casual users interested in reliable performance. Its combination of efficiency, safety features, and ease of maintenance make it an excellent choice for anyone looking to tackle wood cutting tasks with confidence.
Top Page Image Contents