Sears 917.25545 To Adjust Throttle Control Cable See Fig, Acceleration Test, Preliminary Setting

Page 23

SERVnCE AND

ENGINE

TO ADJUST THROTTLE CONTROL CABLE (See Fig. 30)

The throttle control has been preset at the factory and adjustment should not be necessary. Check adjustment as

described below before loosening cable_ If adjustment is necessary, procede as follows:

oWith engine not running, move throttle control lever from "SLOW" to "CHOKE" position Slowly move lever from "CHOKE" to "FAST" position_

oCheck to see if hole in throttle lever and hole in speed control bracket are aligned.

°If holes are not aligned, loosen cable clamp screw and align the holes by inserting a pencil or a 1/4" drill bit through both holes,

•Pull throttle cable up to remove slack and tighten cable clamp screw. Remove alignment pencil or drill bit,

ADJUSTMENTS

ACCELERATION TEST -

°Move throttle control lever from "SLOW" to "FAST" position. If engine hesitates or dies, turn idle fuel adjusting needle out (counterclockwise) 1/8 turn. Re- peat test and continue to adjust, if necessary, until engine accelerates smoothly.

High speed stop is factory adjusted Do not adjust - damage may resulL

IMPORTANT: NEVER TAMPER WITH THE ENGINE GOVERNOR, WHICH IS FACTORY SET FOR PROPER ENGINE SPEED. OVERSPEEDINGTHE ENGINE ABOVE THE FACTORY HIGH SPEED SETTING CAN BE DANGEROUS IFYOUTHINKTHEENGINE-GOVERNED HIGH SPEED NEEDS ADJUSTING, CONTACT YOUR

NEAREST SEARS SERVICE CENTER, WHICH HAS PROPER EQUIPMENT AND EXPERIENCE TO MAKE ANY

NECESSARY ADJUSTMENTS

TO ADJUST CARBURETOR (See Fig. 3'1)

]he carburetor has been preset at the factory and adjust- ment should not be necessary. However, minor adjust- ment may be required to compensate for differencesin fuel, temperature, altitude or load If the carburetor does need adjustment, proceed as follows:

In general, turning the adjusting needles in (clockwise) decreases the supply of fuel to the engine giving a leaner fuel/air mixture Turning the ad usting needles out (counter- clockwise) increases the supply of fuel to the engine giving a richer fuel/air mixture_

IMPORTANT: DAMAGE TO THE NEEDLES AND THE

SEATS IN CARBURETOR MAY RESULT IF NEEDLE IS TURNED IN TOO TIGHT

CABLECLAMPSCREW._

SPEEDCONTROLBRACKET_

THROTTLE LEVER

PRELIMINARY SETTING -,

. Be sure you have a clean air filter and the throttle control cable is adjusted properly (see above)

=With engine off turn idle fuel adjusting needle in (clock-

wise) closing it finger tight and then turn out (counter- clockwise) 1 turn.

FINAL SE'I-FING -

°Start engine and allow to warm for five minutes. Make final adjustments with engine running and shift/motion control lever in "NEUTRAL" position.

•Idle speed setting - With throttle control lever in"SLOW" position, engine should idle at 1625 RPM If engine

idles too slow or fast, turn idle speed adjusting screw in or out until correct idle is attained_

Idle fuel needle settinq - With throttle control lever in "SLOW" position, turn idle fuel ad usting needle in (c ockw se) unti eng ne beg ns to die and then turn out (counterclockwise) approximately 1/8 to 1/4 turn to obtain best low speed performance,

Recheck idle speed, Readjust if necessary,

FIG. 30

IDLE SPEED ADJUSTING SCREW

IDLE FUEL ADJUSTING NEEDLE

FIG. 31

23

Page 22 Page 24
Image 23
Page 22 Page 24
Contents SEA Your Safety is InvolvedSafe Operation Practices for Ride-On Mowers SEARS, Roebuck and CO, D/817WA, Hoffman ESTATES, IL Maintenance AgreementModel Blade Bolt TorqueNNDEX Performance EngineContents of Hardware Pack To Roll Unit OFF Skid See Fig To Remove Unit from CartonUnpack Carton Attach Steering Wheel See FigCheck for Proper Position of ALL Belts Asse LYCheck Tire Pressure Check Deck LevelnessWingnuts AssemblyInstall Battery See Figs Check Brake SystemTo Convert to Bagging or Discharging Install Mulcher Plate See Figs aFIG, 7A Know Your Tractor OperationSee Fig To Adjust Mower Cutting HeightTo SET Parking Brake See Fig To Move Forward and BackwardTo Transport To Operate on HillsADD Gasoline Mulching Mowing Tips OperationClutch Pivots SpindlezerkqBefore Each USE Blade Care Battery See FigBlade Removal See Fig Brake Operation2oo .loo 6 oo 40 Customer RespoEngine BeltsSparkplugs CleaningClean AIR INTAKE/COOLING Areas Engine OIL Filter See FigIf AN Attachment Other than To Install Mower See FigTo Remove Mower See Fig ID d To Level Mower HousingTo Replace Motion Drive Belt See Fig To Adjust Brake See FigTo Replace Mower Blade Drive Belt See Figs Service and AdjustmentsTo Start Engine with a Weak BAFrERY Final SEI-FING To Adjust Throttle Control Cable See FigPreliminary Setting Acceleration TestOther BatteryStorage EnghneTroubleshooting Points Correction ProblemCause

917.25545 specifications

The Sears 917.25545 is a versatile and durable lawn mower that stands out for its combination of power, efficiency, and ease of use. Designed to handle various mowing conditions, this model has become a favorite among homeowners and gardening enthusiasts alike.

At the heart of the Sears 917.25545 is its robust engine, which ensures reliable performance across various terrains. With a significant horsepower rating, this mower can tackle even the thickest grass and tricky landscapes with ease. The engine's design focuses on fuel efficiency, allowing users to mow longer without frequent refueling, making it an economical choice for lawn maintenance.

One of the standout features of the Sears 917.25545 is its adjustable cutting height. This mower offers multiple settings to accommodate different types of grass and seasonal variations. Whether it’s a quick trim or a more rigorous mowing session, users can customize the cutting height to achieve the desired results. The sharp, precision blades ensure a clean cut, promoting healthy grass growth.

In terms of maneuverability, the Sears 917.25545 is equipped with large rear wheels that provide excellent traction and stability, especially on uneven ground. This feature allows users to navigate around obstacles and tight corners effortlessly, reducing the stress of mowing a complex yard.

The mower's build quality is another highlight. Constructed from durable materials, the Sears 917.25545 is designed to withstand the rigors of regular use. The deck is rust-resistant, ensuring longevity and minimal maintenance over the years. Additionally, the model is relatively lightweight, which enhances its portability and ease of storage.

For added convenience, the Sears 917.25545 incorporates user-friendly features such as a simple pull-start mechanism and an ergonomic handle for comfortable control. These aspects minimize fatigue during operation, allowing users to complete their mowing tasks more efficiently.

Lastly, the Sears 917.25545 emphasizes safety with features like a blade brake that ensures the engine stops quickly when necessary. This essential safety feature gives users peace of mind while working.

In summary, the Sears 917.25545 is an exceptional lawn mower that perfectly balances power, efficiency, and user comfort. Its range of features, including adjustable cutting heights, durable construction, and safety mechanisms, makes it a reliable choice for maintaining any lawn.
Top Page Image Contents