Sears 917.2566 owner manual Install Mulcher Plate See Figs a, Discharging

Page 10

ASSEMBLY

m

INSTALL MULCHER PLATE (See Figs. 5A and

5B)

-Install two latch hooks to mulcher plate using screw, washer, lock washer, and weld nut as shown.

NOTE: Pre-assemble weld nut to latch hook by inserting weld nut from the top with hook pointing down.

. Tighten hardware securely.

-Raise and hold deflector shield in upright position.

•Place front of mulcher plate over front of mower deck opening and slide into place, as shown.

•Hook front latch into hole on front of mower deck.

•Hook rear latch into hole on back of mower deck.

&CAUTION: Do not remove discharge guard from mower. Raise and hold guard when attaching mulcher plate and allow it to rest on plate while in operation.

 

 

HOOK POINTS

WELD

NUT

DOWN

FROM

THE TOP

 

LOCK

WASHER

WELD.SCREW

NUT "_

LATCH

HOOK

LOCK WELD

WASHER NUT

WASHER

WASHER

MULCHER\__.._

PLATESCREW

FiG. 5A

DEFLECTOR

SHIELD

TO CONVERT TO BAGGING OR

DISCHARGING

Simply remove mulcher plate and store in a safe place. Your mower is now ready for discharging or installation of optional grass catcher accessory.

NOTE: It is not necessaryto change blades. The mulcher blades are designed for discharging and bagging also.

v"CHECKLIST

BEFORE YOU OPERATE AND ENJOY YOUR NEW

TRACTOR, WE WISH TO ASSURE THAT YOU RECEIVE THE BEST PERFORMANCE A ND SA TISFA CTION FROM

THIS QUALITY PRODUCT.

PLEASE REVIEW THE FOLLOWING CHECKLIST:

,/ Al! assembly instructions have been completed.

,/ No remaining loose parts in carton.

•/ Batteryis properly prepared and charged. (Minimum 1 hour at 6 amps).

,/ Seat is adjusted comfortably and tightened securely.

,/ All tires are properly inflated. (For shipping purposes, the tires were overinflated at the factory).

#" Be sure mower deck is properly leveled side-to-side/ front-to-rear for best cutting results. (Tires must be properly inflated for leveling).

,/ Check mower and drive belts. Be sure they are routed properly around pulleys and inside all belt keepers.

,/ Checkwiring. See that atl connections are still secure and wires are properly clamped.

WHILE LEARNING HOWTO USE YOUR TRACTOR, PAY EXTRA A TTENTION TO THE FOLL OWING IMPORTANT

ITEMS:

,/ Engine oil is at proper level.

,/ Fuel tank is filled with fresh, clean, regular unleaded gasoline.

,/ Become familiar with all controls - their location and function. Operate them before you start the engine.

,/ Be sure brake system is in safe operating condition.

it\"

JJk' l\

_"LATCH

HOOKS

FIG. !iB

10

Page 9 Page 11
Image 10
Page 9 Page 11
Contents RoFTZHaN Model Number 917.256600 OwnersmanualSafe Operation Practices for Ride=On Mowers Safety is InvolvedI11. Children Limited TWO Year Warranty on Craftsman Riding Equipment Maintenance AgreementProduct Specifications Customer ResponsibilitiesIndex Engine Maintenance AccessoattachmentsPerformance Contents of Hardware Pack To Remove Tractor from Carton AssemblyTools Required for Assembly Before Rolling Tractor OFF SkidConnect Batiery See Fig Install Seat See FigCheck Tire Pressure Check Deck Levelness Install Mower and Drive Belt SeeCheck for Proper Position of ALL Belts Install Mulcher Plate See Figs a DischargingOperation Attachment Clutch Switch Used to engage Know Your TractorOperation HOW to USE Your TractorTo Move Forward and Backward Shoulderbolt To Adjust Gauge Wheels See FigBefore Starting the Engine To Operate Mower See FigTo Start Engine See Fig TRASH. Clean After Each USEMowing Tips Mulching Mowing TipsGeneral Recommendations Lubrication ChartCustomer Responsibilities Each USEBlade Care BatteryTractor To Sharpen Blade See FigTransaxle Cooling Clean AIR Screen See FigEngine BeltsMuffler Clean AIR INTAKE/COOLING AreasEngine OIL Filter See Fig Spark PlugsTo Level Mower Housing ServiceAdjustments Recheck measurements After adjustingTo Replace Mower Drive Belt Service and AdjustmentsEqually SO Mower will Stay Level SIDE-TO- Side Electric clutch should provide years of service. To Adjust Attachment Clutch SeeTo Adjust Brake See Fig To Replace Mower Blade Drive Belt See FigTransaxleii ,--J1--= To Adjust Steering Wheel AlignmentTransaxle Shifter Linkage and AD- Justment See Figs Frontwheel TOE-IN/CAMBERTo Start Engine with a Weak BAI-rERY See Fig To Remove Hood and Grill AssemblyTo Remove Wheel for Repairs See Fig Interlocks and RelaysTo Adjust THROnLE Control Cable See Fig To Adjust Carburetor See FigEngine OIL StorageOther Fuel SystemProblemcause Troubleshooting PointsCorrection Problem Cause CorreconWiring Tractor - Model Number SchematicIgnition Switch ClipsTractor = Model Number ElectricalInterLock KEY Part DescriptionPTO Tractor = = Model Number Chassis and EnclosuresTractor - Model Number PlateDrive 3637KEY Part NO, no Tractor = = Model NumberDrive 121520XSteering Assembly DESCRiPTiON Tractor -- Model NumberKEY Part WheelEngine Engine Tractor - Model NumberKEY Part NO. NO.DESCRIPTION Seat Assembly Tractor Model NumberDecals Wheels & TiresMower Lift 41I 521Mower Lift Tractor --MODEL Number 917,256600Spring Retainer Mower Deck 1O5 104 106 101Tractor -= Model Number Part KEY DescriptionTractor - Model Number 917,256600 Dana Transaxle Model NumberKEY Part Description NO. no Dana Transaxle = Model Number640 AIR Intake Blower H O Tractor -- Model NumberKohler Engine Model Number CV15S, Type Number PS41525 Engine Controls JCrankshaft KEY Part Description Cylinder HEAD, Valve and Breather 21 \Kohler Engine = Model Number CV15S, Type Number PS41525 Fuel System KEY Part NO. noTractor - Model Number 917,256600 KEY Part NO. no Service Notes Only Ride UP and Down Hill Not Across Hill Sighting Sight and Hold this Level with SKY Line or TreeModel Number Engine Model NO. CV15S PS41525 If YOU Need Repair Service Or PartsFor Repair SERVICE, Call this Toll Free Number Part Number Part Description
Top Page Image Contents