Sears 917.25051 SE CE Ustm NTS, To Remove Mower See Fig, To Install Mower, To Level Mower Housing

Page 20

SE CE

USTM NTS

with plug.

TO REMOVE MOWER (See Fig. 19)

,,Place attachment clutch in "DISENGAGED" position. = Turn height adjustment knob to lowest setting.

Lower mower to its lowest position.

Remove retainer spring holding anti-swaybar to chas- sis bracket and disengage anti-swaybar from bracket.

-Remove retainer springs from suspension arms at deck and disengage arms from deck.

=Raise attachment lift to its highest position.

Remove two retainer springs from each front link and remove links.

-Slide mower forward and remove belt from electric clutch pulley.

=Slide mower out from under right side of tractor.

IMPORTANT: IF AN ATTACHMENT OTHER THAN THE MOWER DECK IS TO BE MOUNTED ON THE TRACTOR, REMOVE THE FRONT LINKS.

TO INSTALL MOWER

Follow procedure described in "INSTALL MOWER AND DRIVE BELT" in the Assembly section of this manual•

ADJUSTMENT

 

 

NUTS

LiFT

FRONT

 

 

LINKS

SUSPENSION

SUSPENSION

 

BRACKET

 

 

ARMS

 

 

 

 

BRACKET

CHASSIS

 

 

TO LEVEL MOWER HOUSING

Adjust the mower while tractor is parked on level ground or driveway. Make sure tires are properly inflated (See "PRODUCT SPEC tFICATIQNS" on page 3 of this manual). Iftires are over or underinfiated, you will not properly adjust your mower.

SIDE-TO-SIDE ADJUSTMENT (See Figs. 19 and 20)

,Raise mower to its highest position.

Measure height from bottom of deck curl to ground level at front corners of mower. Distance "A" on both sides of mower should be the same.

If adjustment is necessary, make adjustment on one side of mower only.

-To raise one side of mower, tighten lift link adjustment nut on that side.

To lower one side of mower, loosen lift link adjustment nut on that side.

NOTE: Each fun turn of adjustment nut will change mower

height about

3/16",

Recheck

measurements after adjusting.

BOTTOM

BOTTOM

OFCURL

OFCURL

FRONT

SUSPENSION

BRACKET

RETAINER

RETAINER

SPRING

ANTI-SWAY

\

NGS

BRACKET

BARRETAINER

SPRINGS

FIG. 19

\

2O

Image 20
Contents Convertible II. Slope Operation Safe Operation Practices for Ride-On MowersIII. Children Maintenance Agreement ModelContents Accessori and Attach Ents MaintenanceEngine PerformanceContents Pack Tools Required for Assembly To Remove Tractor from CartonUnpack Carton Attach Steering Wheel See FigAssembly Connect Battery See FigInstall Seat See Fig Check Tire PressureInstall Mower and Drive Belt See FigsCheck Deck Levelness Check for Proper Position of ALL BeltsChecklist Install Mulcher PlateSee Figs a and 5B To Convert to Bagging or DischargingOperation LockOperation Know Your TractorTo Adjust Mower Cutting Height To Adjust Gauge Wheels See Fig Check Engine OIL Level See FigADD GasolineMulching Mowing Tips Mowing TipsTo Start Engine See Fig Lubrication Chart Maintenance ScheduleCustomer Responsibilities General RecommendationsTractor Brake OperationTires Blade CareBattery To Clean Battery and TerminalsCustom Espo Ilities LubricationIN=LfNE Fuel Filter See Fig Spark PlugsEngine OIL Filter To Install Mower To Level Mower HousingSE CE Ustm NTS To Remove Mower See FigAdjustments To Replace Mower Drive BeltService To Adjust Attachment ClutchTo Adjust Brake See Fig To Replace Mower Blade Drive Belt See FigService and Adjustments To Adjust Steering .WHEEL AlignmentFront Wheel TOE-IN Adjustment To Replace Motion Drive Belt See FigService Adjustments See FigsTo Replace Headlight Bulb Interlocks and RelaysTo Adjust Attachment LiFT Spring To Remove Hood and Grill Assembly See FigTo Adjust Throttle Control Cable See Figs To Adjust Carburetor See Fig=Final Setting EngineSERV!CE Notes Fuel SystemEngine OIL CyundersProblem Cause Correction TRO Leshooting NTSProblem Cause CorrectionTractor = Model Number Schematic Wiring Insulated ClipsStorage Tractor - Model Number ElectricalTractor = -MODEL Number KEY PartTractor - Model Number 917,250510 Chassis and EnclosuresTractor == Model Number NO. noDescription KEY Part NO. noOUtDD\ KEY Part Description Tractor = Model NumberGround Drive Steering Assembly Steering Assembly KEY Part NO, no2627 Tractor = Model Number KEY Part NO. NO. Description Seat AssemblyDescription KEY Part Description Tractor = = Model NumberDecals Repair Parts Tractor .. Model Number 9 Lift AssemblyKEY Part NO. no Lift AssemblyTractor =- Model Number Mower Deck Tractor =- Model Number 917,250510 Tractor -- Model Number TransaxleTractor o .- Model Number 917=250510 Kohler Engine Model Number MV20S, Type Number Baffles and RoudTractor ---MODEL Number Kohler Engine Model Number MV20S, Type NumberAIR Intake KEY Part NO. no Baffles & Shroud KEY Partdescription NO. noTractor --MODELNUMBER Kohler Engine = Model Number MV20S, Type NumberTractor -.- Model Number Crankcase KEY PartCarburetor Description KEY PartKohler Engine Model Number MV20S Type Number CrankshaftTractor -MODEL Number Tractor =- Model Number Flywheel KEY Partdescription Fuel Pump KEY PartNO, no Governor KEY Part NO. noCamshaft and Valves Kohler Engine --MODEL Number MV20S, Type Number Camshaft & ValvesPiston & ROD KEY Part Description OIL Pump KEY Partdescription NO, noICE Otes Page RV!CE Suggested Guide for Sighting Slopes for Safe Operation MAXIf YOU Need Repair Service Or Parts For Repair SERVICE, Call this Toll Free NumberOwners Manual Part Number ,PART Description

917.25051 specifications

The Sears 917.25051 lawn mower is a product that has made its mark in the gardening and landscaping sectors, renowned for its combination of robust features, advanced technologies, and user-friendly design. This model is particularly favored by homeowners who appreciate both efficiency and reliability when maintaining their lawns.

At the heart of the Sears 917.25051 is its powerful gas engine, which provides an impressive amount of torque and horsepower, making it suitable for a variety of grass types and terrains. The engine is complemented by an easy-start mechanism that minimizes the hassle of getting the mower up and running. This enables even novice users to quickly begin their mowing tasks with minimal fuss.

One of the standout characteristics of the Sears 917.25051 is its cutting deck, which boasts a generous width, allowing users to cover larger areas in less time. The cutting height is adjustable, providing homeowners with the flexibility to achieve their desired lawn length, whether aiming for a traditional manicured look or leaving grass slightly longer for increased resilience. The mower is equipped with sharp, durable blades engineered to deliver a clean cut, which is crucial for promoting healthy grass growth.

The technology used in the Sears 917.25051 also includes features aimed at enhancing user comfort and control. The ergonomic handle is designed for maximum comfort, reducing strain during extended use. The mower's lightweight construction makes it easy to maneuver, even in tight spaces, ensuring that users can navigate around flower beds, trees, and other landscaping elements without difficulty.

In terms of maintenance, the Sears 917.25051 is designed with user convenience in mind. The air filter is easily accessible, allowing for quick cleaning and replacement as needed. Additionally, the fuel tank features a transparent section, which helps users monitor fuel levels without having to open or remove the lid.

Durability is another notable aspect of the Sears 917.25051. Constructed with high-quality materials, this mower is built to withstand the rigors of regular use while retaining optimum performance. The wheel assembly is also robust, providing stability on uneven terrain and ensuring a smooth mowing experience.

In conclusion, the Sears 917.25051 lawn mower is an exceptional choice for homeowners seeking a blend of power, performance, and ease of use. Its combination of advanced features and reliable technology ensures that maintaining a beautiful lawn is an achievable task for anyone ready to take on the challenge. With proper care, this mower can serve its users well for many seasons to come.