Sears 172.10855 warranty Making Bevel Cuts Figs Making Pocket Cuts Fig, Routine Maintenance

Page 13

OPERATION cont.

MAKING BEVEL CUTS (Figs. 16) cont.

!WARNING: If the blade comes in contact with the workpiece before it reaches full speed, it could cause the saw to kickback towards you, possibly resulting in serious injury.

NOTE: Since the thickness of blades varies, MAKE A TRIAL CUT in scrap material along the guideline to determine how much, if any, you should offset the blade from the guideline to allow for the kerf of the blade to get an accurate cut.

MAKING POCKET CUTS ( Fig. 17)

!WARNING: ALWAYS adjust bevel setting to zero before making a pocket cut. Attempting a pocket cut at any other setting can result in a loss of control of the saw, which can result in serious injury.

1.Adjust the bevel setting to zero, set the blade to the correct blade depth setting, then use the lower blade guard lever to swing the guard up.

!WARNING: ALWAYS raise the lower blade guard with the lever to avoid serious injury.

MAINTENANCE

!WARNING: To ensure safety and reliability, all repairs - with the exception of the externally accessible brushes - should be performed by a qualified service technician at a Sears Service Center.

!WARNING: For your safety, ALWAYS turn off switch and unplug circular saw from the power source before performing any maintenance or cleaning.

It has been found that electric tools are subject to accelerated wear and possible premature failure when they are used to work on fiber glass boats and sports cars, wallboard, spackling compounds or plaster. The chips and grindings from these materials are highly abrasive to electrical tool parts, such as bearings, brushes, commutators, etc. Consequently, it is not recommended that this tool be used for extended work on any fiberglass material, wallboard, spackling compound or plaster. During any use on these materials, it is extremely important that the tool is cleaned frequently by blowing with an air jet.

!WARNING: Always wear safety goggles or safety glasses with side shields during power tool operations, or when blowing dust. If operation is dusty, also wear a dust mask.

ROUTINE MAINTENANCE

2.While holding the lower blade guard up by the lever, firmly rest the front of the saw base flat against the workpiece with the rear handle raised so the blade does not touch the workpiece (see Fig 17).

3.Squeeze the trigger switch to start the saw. ALWAYS let the blade reach full speed, then slowly lower the blade onto the workpiece until the base is flat against the workpiece. AS the blade enters the material, you MUST release the lower blade guard lever.

Fig. 17

!WARNING: DO NOT at any time let brake fluids, gasoline, petroleum-based products, penetrating oils, etc. come in contact with plastic parts. Chemicals can damage, weaken or destroy plastic, which may result in serious personal injury.

Periodic maintenance allows for long life and trouble-free operation. A cleaning, lubrication and maintenance schedule should be maintained. As a common preventive maintenance practice, follow these recommended steps:

1. When work has been completed, clean the tool to allow smooth functioning of the tool

over time.

2. Use clean damp cloths to wipe the tool.

3. Check the state of all electrical cables.

4. Keep the motor air openings free from oil, grease and sawdust or woodchips, and store

tool in a dry place.

4.After you complete the cut, release the trigger switch and allow the blade to come to a complete stop. After the blade has stopped, remove it from the workpiece. If the corners of your pocket cut are not completely cut through, use a hand finishing saw to finish the corners.

!WARNING: NEVER tie the lower blade guard in the raised position. Leaving the blade exposed could result in serious injury.

24

5. Be certain that all moving parts that are exposed are well lubricated, particularly after

lengthy exposure to damp and/or dirty conditions.

LUBRICATION

All of the bearings in this tool are lubricated with a sufficient amount of high-grade lubricant for the life of the tool under normal operating conditions. Therefore, no further lubrication is required.

25

REV 10855

2-12-08

Page 12 Page 14
Image 13
Page 12 Page 14
Contents Sears, Roebuck and Co., Hoffman Estates, IL 60179 U.S.A 4-in. Circular SawSafety Symbols Table of ContentsSafety Instructions Safety InstructionsWork Area Safety Personal SafetyElectrical Safety SAFETYSAFETYINSTRUCTIONScontcontSafety Symbols for Your Tool Service SafetySafety Rules for Circular Saws Safety Rules for Circular SawsAdditional Rules for Safe Operation Work in a well-ventilated areaUnpacking Glossary of Terms for WoodworkingAdditional Rules for Safe Operation Assembly AssemblyUnpacking Description This Circular Saws have the following featuresDescription Know Your Circular SAW FigOperation OperationSAW Blades Causes of KickbackWays to Help Prevent Kickback Making DEPTH-OF-CUT Adjustments FigTo SET the Blade Depth a To Help Maintain Control Starting a CUT FigMaking Cross Cuts and RIP Cuts and 12a Installing and Using the Edge Guide sold separately Fig HOW to SET Your Bevel Angle FigMaking RIP Cuts Making Bevel Cuts FigsRoutine Maintenance MaintenanceMaking Bevel Cuts Figs Making Pocket Cuts Fig LubricationAccessories TroubleshootingIf the blade does not follow a straight line If the blade binds or smokes from frictionGet it fixed, at your home or ours

172.10855 specifications

Sears 172.10855, a prominent model in the realm of home appliances, has gained attention for its innovative features, reliability, and user-friendly design. This versatile appliance is designed to meet the needs of modern households, combining style with functionality.

One of the standout features of the Sears 172.10855 is its energy efficiency. Equipped with advanced technologies, this model is built to minimize energy consumption while delivering optimal performance. The Energy Star certification ensures that consumers can rely on this appliance not only for its effectiveness but also for its environmental impact.

The design of the Sears 172.10855 emphasizes ease of use. The intuitive controls are user-friendly, making it accessible for individuals of all ages. Whether navigating through various settings or adjusting temperature and settings, users will find the experience seamless and straightforward.

In terms of performance, the Sears 172.10855 excels with its powerful motor and robust build quality. This appliance is designed to handle a variety of tasks, from simple weekly chores to more demanding jobs. Its versatility allows it to adapt to different kitchen environments and user preferences, making it a staple for many homeowners.

Another important aspect of the Sears 172.10855 is its capacity. It offers ample space for various cooking or storage needs, making it ideal for both small families and larger households. The spacious interior ensures that users can efficiently organize their items without the hassle of overcrowding.

Safety is also a priority in the design of the Sears 172.10855. The appliance features multiple safety mechanisms that protect users from potential hazards, such as overheating or electrical malfunctions. These safety features provide peace of mind, allowing users to focus on their tasks without unnecessary worry.

Additionally, the Sears 172.10855 is aesthetically pleasing, blending well into any kitchen decor. Its modern design and sleek finishes enhance the overall look of the space, making it a functional yet stylish addition to a household.

In conclusion, the Sears 172.10855 stands out in the market due to its energy efficiency, user-friendly design, powerful performance, ample capacity, and robust safety features. For those seeking a reliable, versatile appliance that combines modern technology with ease of use, the Sears 172.10855 is an excellent choice that meets the demands of contemporary living.
Top Page Image Contents