Sears 580.75151 manual After Each USE, Long Term Storage, Other

Page 17

STORAGE

AFTER EACH USE

Water should not remain in the unit for long periods of time. Sediments of minerals can deposit on pump parts and "freeze" pump action. Follow these procedures after every

use:

Flush detergent hose by placing the injector filter into a pail of clear water while running Pressure Washer with no771e in low pressure mode. Flush for five min- uteso

Shut off the engine and let it cool, then remove all hoses.

CAUTION:"STOP" POSITIONBE SUREBEFORETHE THROTTLEYOU CONTINUELEVER . IS iNtF

YOU START THE ENGINE WITHOUT THE PROPER

WATER SUPPLY CONNECTED, YOU CAN DAM- AGE THE PUMP.

•Empty the pump of all pumped liquids by pulling recoil handte about 6 times. This should remove most of the

liquid in the pump.

oCoil the high pressure hose and inspect it for damage. Cuts in the hose or fraying of it could result in leaks and loss of pressured Should any damage be found, replace the hose. DO NOT attempt to repair a damaged hose and use it, Replace the hose with the genuine Crafts- man part.

•Drain water from hose and properly hang it on the wire support provided on the guide handle

NOTE: To protect the unit from freezing temperatures, you can draw windshield washer fluid into the pump by pouring the washer fluid into a 3-foot section of garden hose corn

nected to the inlet adapter and pulling the recoil handle twice_

o Store in a clean, dr,/area.

LONG TERM STORAGE

WARNING: NEVER STORE ENGINE WITH FUEL iN

TANK INDOORS OR IN ENCLOSED, POORLY VEN- TILATED AREAS WHERE FUMES MAY REACH AN

OPEN FLAME, SPARK OR PILOT LIGHT AS ON A FURNACE, WATER HEATER, CLOTHES DRYER OR OTHER GAS APPLIANCE,

If you do not plan to use the Pressure Washer for more than 30 days, you must prepare the engine for long term storage.

NOTE: As always, prepare the pressure washer pump as you would after each use°

It is important to prevent gum deposits from forming in essential fuel system parts such as the carburetor, fuel filter, fuel hose or tank during storage_ Also, experience indicates that alcohol-blended fuels (called "gasohot" or using ethanol or methanol) can attract moisture which leads to separation and formation of acids during storage. Acidic gas can damage the fuel system of an engine while in storage°

To avoid engine problems, the fuel system should be

emptied before storage of 30 days or Ionger_ Follow these instructions:

Protect Fuel System: Engines stored over 30 days need to be protected or drained of fuel to prevent gum deposits from forming in fuel system or on essential carburetor parts.

°For en_i_e protection use a fuel stabilizer (such as STA-BIL .Mix stabilizer with fuel in fuel tank and run

engine for short time to circulate stabilizer through carburetor.

-If you did use "gasohol", run engine until engine stops from lack of fuel. Make sure you have water supply to pump inlet connected and turned ONo

Change Oi1: While engine is still warm, drain oil from crankcase. Refill with recommended grade_

Oil Cyllnder Bore: Remove spark plug and pour about 1/2 ounce (15ml) of engine oil into the cylinder. Cover spark plug hole with rag. Crank slowly to distribute oil

I .,_ CAUTION' AVOIDSPRAYFROMSPARKPLUG

HOLE WHEN CRANKING ENG,NE SLOWLY.

o Install spark plug.. Do not connect spark plug wire.

OTHER

oDo not store gasoline from one season to another.

°Replace your gasoline can if your can starts to rusL Rust and/or dirt in your gasoline will cause problems.

otf possible, store your unit indoors and cover it to give protection from dust and dirt,

oCover your unit with a suitable protective cover that does not retain moisture.

IMPORTANT: NEVER COVER YOUR PRESSURE WASHER WHILE ENGINE AND EXHAUST AREAS ARE

WARM,

/7

Page 16 Page 18
Image 17
Page 16 Page 18
Contents Service Adjustment AssemblyMort.- Fri a.m. to 5 p.m OperationTraining Safety PRECAUTIONS. IT Means ATTENTION!It bePreparation OperationPressure Washer Specifications Product SpecificationsMaintenance Agreement Engine SpecificationsTable of Contents Wash Accessories and AttachmentsGauge Contents of Hardware Pack To Remove Pressure Washer from AssemblyTools Required for Assembly Pump ChecklistQuick Connect OperationDetergentpick Uptube Andfilter HOW to USE Your Washer Before Starting the Engine HOW to USE Optional Turbo NozzleStoring Nozzles To Turn on Washer OperationColder32Fwarmer IMPORTANT do not RUN Pump Without To Start EngineTips Customer Responsibjlitiies Pressure Washer MaintenanceGeneral Recommendations Before Each USECustomer Responsibility Pump MaintenanceEngine Maintenance Adjustments ServiceEngine Adjustments CarburetorAfter Each USE StorageLong Term Storage OtherCorrection TroubleshootingOwnersManual notshown1 req Craftsman 1800 PSI High Pressure Washer Repair PartsDescription Briggs & Stratton 4-CYCLE Engine Craftsman 1800 PSi High Pressure Washer133212-0159-01 346 357 615 616 592 220256 202217 392269 268 270 271985 353346A 335 356 Craftsman 1800 PSI High Pressure133212-0159-01 373 461 69A 515 305 613A 670 304 334 346 455 Part Name NO. NoThis warranty does not cover Full TWO Year Warranty on Gasoline Engine133212-0159-01 Part Part Name Part Name4t,.l,j2 KIT Part no Description K1TPART no Craftsm AN 1800 PSI High Press UR E Washer Repair Parts8O0-366-7278 Owners ManualModel Number Engine Model NUMBER-= Part Number Part Description

580.75151 specifications

The Sears 580.75151 is a vintage sewing machine that has captured the interest of hobbyists and collectors alike. This model reflects the qualities that made Sears a household name, merging functionality with a robust design.

One of the standout features of the Sears 580.75151 is its solid construction which contributes to the machine's durability. This model is built with a heavy-duty metal frame, ensuring stability while sewing, which is a critical factor for achieving even and professional-looking stitches. The weight and build quality make it less susceptible to vibrations, providing a smoother sewing experience.

The machine offers a variety of stitch options, making it versatile for different sewing projects. Users benefit from several straight and zigzag stitch settings, allowing them to customize their sewing tasks easily. The adjustable stitch length is another feature that enhances creativity, enabling users to create fine or bold patterns as desired. Additionally, it includes a reverse stitch function, which is essential for securely finishing seams.

One of the technological highlights of the Sears 580.75151 is its reliable drop-in bobbin system. This feature simplifies the process of threading and reloading the bobbin, minimizing downtime during sewing projects. The clear view cover over the bobbin area allows users to monitor the thread supply without interrupting their workflow.

In terms of ease of use, the machine is designed with an adjustable presser foot pressure, which provides better control over various fabric types. This adaptability is particularly beneficial for those who work with both lightweight and heavy materials. The machine also includes a built-in needle threader, which helps decrease the frustration of threading the needle, a common challenge for sewists.

The Sears 580.75151 is also known for its low maintenance requirements, with users appreciating the straightforward cleaning process. Its accessibility makes it an excellent option for both beginners and experienced sewists looking for a reliable machine that doesn’t require constant upkeep.

Overall, the Sears 580.75151 stands out as a solid sewing machine that combines vintage charm with practical features. Its variety of stitch options, durable construction, and user-friendly technologies make it a favorite among those who value quality and dependability in their sewing tools.
Top Page Image Contents