Sears 580.7515 manual HOW to SET UP Your Pressure Washer, Tools Required for Assembly

Page 7

ASSEMBLY

Read these iv,sttuctions and Operator's Manual in its en- tirety before you attempt to assemble or operate your new high pressure washer° Your high pressure washer has, for the most part, been asserr_ed at the factory, except those parts left unassembted. Before you can operate your new high pressure washer, you must assemble the wheel kitand property connect the high pressure hose.

IF YOU HAVE ANY PROBLEMS WITH THE ASSEMBLY

OF YOUR PRESSURE WASHER, PLEASE CALL THE PRESSURE WASHER HELPLINE AT 1-800-_-3136.

HOW TO SET UP YOUR PRESSURE WASHER

TO INSTALL THE WHEEL KIT

Installing the wheel kit requires the tools listed, the guide handle and items included in the parts carton°

°Prop up the engine end of the main unit. This will allow you to slip each axle pin into the holes provided on the side of the base (Fig 1).

JAM

TOOLS REQUIRED FOR ASSEMBLY

oMallet

=2 adjustable wrenches OR the following wrenches:

=, 5/16" (8mm) combination wrench

=1/2" (13mm) combination wrench

-5/8'(16mm) combination wrench

=11/16" (18mm) combination wrench

=7/8" (22ram) combination wrench

=15/16" (24mm) combination wrench

LOGK1NASHER

JAM NUT

_L

 

REVERSE ANGLE

FLAT v

TO REMOVE PRESSURE WASHER FROM CARTON

=, Remove two boxes marked "PARTS INSIDE" and re- move the parts contained in both boxes.

=Remove unit with one hand under pump and one hand under recoil starter.

Refer to Page 6, "Contents of Hardware Pack" for an illustrated listingof all the items included with your pressure washer, Become familiar with each piece before assem- bling the pressure washer,, Check all contents against the illustrations on Page & If any parts are missing or dam-

aged, call the Pressure Washer Helpline at 1-800-222- 3136,

FIG. 1

With the axle pin inserted inside the base, grip the end of the axle pin as shown with an adjustable or 15/16"

combination wrench. This will keep axle from spinning as you fasten axle to the base with a 5/8 lock washer,

a 5/8"-18 JAM nut, and an M12 flat washer..

oPlace wheels on the axles so the rib side of hub is against mounting base.

=Retain each wheel to its axle pin by tapping a push nut onto end of axle with a mallet.

°Attach support legs to base as shown in Fig, 2 with M8 x 20mm hex head capscrews and flange lock nuts,. Tighten with 13mm or 1/2-inch wrench on each fas- tener.. Be sure legs are straight when you are tinished_

•Attach the guide handle to the base as shown in Fig, 2 with two M8 x 40mm hex head capscrews, two M8 washers and two flange nuts.

Installing the Handle

CAPSCREW

GUIDE

 

Installing Support Legs

HANDLE

WASHER

\

WIRE SUPPORT

CAPSC

CAPSCREW

_NUT

FIG. 2

Page 6 Page 8
Image 7
Page 6 Page 8
Contents SEARS, Roebuck and CO., HoffmanEstates, IL 60179 U.S.A Horsepower 1800 PS! 2.5 GPMHours Preparation Look for this Symbol to Point OUT ImporiantMaintenance and Storage TrainingProduct Pecifications Maintenance AgreementCustomer Responsibilities Table of Contents Turbo Nozzle Accessories and AttachmentsLifiJliirlliiFllIl!fltiiJllr!!tlU Contents of Hardware PackTo Install the Wheel KIT AssemblyHOW to SET UP Your Pressure Washer Tools Required for AssemblyWire Support ChecklistDetergent Pickup Tube Know Your High Pressure Washer OperationHigh Pressure Gasoline CA QUICK-CONNECT Recoil Starter First, move engine throttle lever to OEW position Fig HOW to USE Your WasherHOW Touse Adjustable Nozzle Spray Nozzle to Adjust Spray PAT- TernEngine OIL HOW to USE Optional Turbo NozzleBefore Starting the Engine Storing NozzlesTo Turn on Washer GASSiphoning To Start EngineTips Before Each USE Pressure Washer MaintenanceCustomer General RecommendationsEngine Maintenance Pump MaintenanceCustomer Responsnbhuty Engine Adjustments Service and AdjustmentsNozzle Maintenance After Each USE StorageLong Term Storage Problem Craftsman 1800 PSi High Pressure Washer Repair PartsDrawing No Description Item Part noCraftsman 1800 PSI High Pressure Washer Repair Parts Thrust Bearing 1 REQ GUN and Wand Assembly 1 REQItem Part no Description HP Briggs & Stratton Engine 1 REQBriggs & Stratton 4-CYCLE Engine Craftsman 1800 PSI High Pressure187433 435 611 394 127256 1241531012 217 542 779 414 414A 201 232969 967 971 163 190 190A208280206 271 268 269270 985 223 353 520346A 332 670 334 335 356 Craftsman 1800 PSg HiGH Pressure WasherBriggs & Stratton 4-CYCLEENGINE 1016 461 69A 515 305 304 613A 346FeL Part Name PartCep Full ONE Year Warranty on Craftsman High Pressure WasherFull TWO Year Warranty on Gasoline Engine Part Part Name800366-7278 Owners ManualPart Description Lun. Vie a.m. a 5 p.m HorasPrecaucion Reglas DE Seguridad Especlflcaclones de la Mqulna Lavadora a Presi6n Acuerdo DE MantenimientoResponsabiudades DEL Cliente Especificaciones DEL ProductoIndice Tabla DE ContenidosAccessorios Y Conexiones Pistola y Vara Ontendido DE LA Caja DE HerrajeDe las Partes Caja de las PartesInstalaci6n de la Patas de Soporte EnsambleHerramientas Necesarias Para EL Ensamble Instalact6n de la ManljaAuto enmsque #10 y las a.randelasplanas M6 Fig+3. E1 Para Ensamblar LOS Componentes RemanentesLista DE Revsion Una elsoportede atambm a la manijaguiaconlos tomigo deRapida BujiaLlenado DE Aceite VaraOperacion SI TtENE Algun Problema AL Operar SU MAQUtNAComo Utilizar SU Maquina Lavadora Tambien puede concentra Extraido con la embo Caduraen et mode de altaE1 deterlentees apticado a presk.n,para evitar.el AumentarPara operar el motor usted necesitardIo siguiente Antes DE Encender EL MotorAceite Para EL Motor Caucion O LA Bomba SE DAIARA+ Para Encender EL MotorEXTRACClON SugerenciasMotor Esponsabildades DEL ClienteRECOMENDAClONES Generales Antes DE Cada USOTalo Lentamente Camblo de AcellaLlmple et Ststema de Enfrlamento del Motor Mantenimiento DE Embocadura Responsabilidades DEL ClienteVelocidad DEL Motor Ajuste DE MotorTOR SIN EL Suministro DE Agua Apropiado Conectado Bomba DE LA Maquina Lavadora a PresionMotor OtrosCausa ProblemaCorreccion Dubijo No Parties DE REPARAClON Maquina Lavadora DE Alta Presion Craftsman DE580.751500Partes DE Reparacion Maquina Lavadora DE Alta PRESlON DE 1800 PSDubio No Para LA Pagina Motor DE 4 Tiempos Briggs & STRATrON 13A 87il 346 337 635 306 30841 40 1034 615 616 220206A\ 216 201 394 203392 205 127 187256 257 217 779 414 153265 969 967 971971 535 163 280 190 190A 206209 181 268 269270 224 985 223 520 267 526Motor DE 4 Tiempos BRtGGS & Stratton 133212-O159-01 373 1016305 304 613A 670 334 346 455 335 356 461Liste Presion Craftsman Garantia Completa DE UN AlO DE LA Maquina LavadoraGarantia Completa DE DOS Aiios DE LA Motor DE Gasolina Numero DE LA Parte Descripcion DE LA Parte Manual DEL PropietarioEste Ordenando Repuestos Presion

580.7515 specifications

The Sears 580.7515 is a distinctive piece of technology that emerged in the realm of consumer electronics. Primarily recognized as a high-performance rotary tool, the 580.7515 quickly garnered attention for its versatility and efficiency in various applications, which include crafting, repair, and maintenance tasks.

One of the most notable features of the Sears 580.7515 is its powerful motor, which delivers a robust performance that can handle a variety of materials, including wood, metal, and plastic. The tool operates at multiple speeds, enabling users to adjust the RPM according to the specific requirement of their tasks. This flexibility is particularly beneficial for intricate detail work or when more aggressive grinding is necessary.

The design of the Sears 580.7515 emphasizes user comfort and control. It typically features an ergonomic handle that reduces fatigue during prolonged use, providing a secure grip. The tool's lightweight nature further enhances its usability, making it an ideal choice for both professionals and amateur DIY enthusiasts.

In terms of technology, the Sears 580.7515 is equipped with a universal collet system, allowing users to easily interchange a variety of attachments and accessories. This compatibility significantly expands the range of potential applications for the tool. From sanding and polishing to cutting and engraving, the Sears 580.7515 does it all with relative ease.

Safety is also a priority with the Sears 580.7515. The rotary tool often includes safety features such as a protective guard to shield users from debris and a reliable safety switch to prevent accidental activation. These elements work in tandem to create a safer working environment.

Another noteworthy characteristic of the Sears 580.7515 is its robust construction. Built to withstand the rigors of frequent use, this tool is designed for longevity. Many users appreciate its durability, often citing it as a valuable addition to their toolkits.

Overall, the Sears 580.7515 combines power, versatility, and safety in a compact design, making it a reliable choice for anyone looking to tackle a range of tasks with precision and ease. Its adaptability continues to make it relevant in an ever-evolving market, showcasing the enduring appeal of well-crafted tools.
Top Page Image Contents