Maintenance

OPERATION cont.

REMOVING THE BLADE FOR REPLACEMENT

!WARNING: To avoid injury, ALWAYS turn off and disconnect the Edger from the power outlet BEFORE installing parts or cleaning the Edger or making any adjustments.

!CAUTION: BLADE ROTATES momentarily after power switch is released. Wait

for blade to come to a complete stop. Blade is sharp, wear work gloves when replacing.

1.Loosen Screw under Blade Guard Release Lever, pull Blade Guard Release Lever and open Blade Guard Door. See OPENING THE BLADE GUARD on Pages 20-21.

2.Use a 1” crescent wrench to hold the outer spacer in place, which will keep the blade from turning. With a 9/16” crescent wrench, loosen the hex head nut with conical washer (Fig. 15a).

3.Remove hex head nut with conical washer, spacer and blade.

Fig. 15a	with conical washer	Top	Fig. 15b
	Hex Head Nut
	Blade	Spacer	Bottom
	Blade		Bottom
			Spacer
			Shaft

ATTACHING THE NEW BLADE

NOTE: Clean off debris from blade and all mounting hardware.

1.Be sure inner spacer is on shaft – “flats” in spacer hole must engage with “flats” on shaft (Fig 15b).

2.Place the blade on the shaft over the inner spacer.

3.Hold the blade against the inner spacer and install the outer spacer, again aligning the flats in the spacer with the flats on the shaft.

4.Install the hex head nut with conical washer. Use a 1” crescent wrench to hold the outer spacer in place, which will keep the blade from turning. With a 9/16” crescent wrench, firmly tighten the hex head nut with conical washer (Fig 15a).

NOTE: Replace the hex head nut with conical washer ONLY with identical replacement part; see Parts List.

5.Close Blade Guard door. Blade Guard Release Lever must snap into locked position. Tighten screw under Blade Guard Release Lever.

GENERAL MAINTENANCE

Keep your Edger clean and in good repair for maximum long-lasting performance. Before each use, inspect the switch and cord for damage. Check for damaged, missing, or worn parts. Check for loose screws, misalignment, moving parts that are jammed,

or any other conditions that may affect the operation. If abnormal vibration or noise occurs, turn off the tool immediately and have the problem corrected before further use.

DO NOT use the Edger if it has any broken parts. Have damaged, missing, worn or broken parts replaced before using Edger.

When servicing a tool, use only identical replacement parts. Use of unauthorized parts or failure to follow maintenance instructions may create a risk of electric shock or injury.

BLADE CARE

The cutting blades are made from high quality, hardened steel and with normal use, they will not require resharpening. However, if you accidentally hit a wire fence, stones, glass or other hard objects, you may put a nick in the blade. There is no need to remove this nick as long as it does not interfere with the movement of the blade. If it does interfere, unplug the Edger, see OPENING THE BLADE GUARD on Pages 20-21, and use a fine-toothed file or sharpening stone to remove the nick.

!WARNING: To avoid injury, ALWAYS turn off and disconnect the Edger from the power outlet BEFORE installing parts or cleaning the Edger or making any adjustments.

If you drop the Edger, carefully inspect it for damage. If the blade is bent, housing cracked, or handles broken, or if you see any other condition that may affect the Edger’s operation, have Edger repaired by a Sears or other qualified service dealer before putting it back into use.

CLEANING

Fertilizers and other garden chemicals contain agents that greatly accelerate the corrosion of metals. If you use the Edger in areas where fertilizers or chemicals have been used, it should be cleaned immediately afterwards. Do Not store the tool on or adjacent to fertilizers or chemicals.

When cleaning, DO NOT immerse tool in water or squirt with a hose. Never let any liquid get inside the tool.

Wipe all exposed parts with a damp cloth. You may lubricate only metal parts with a light petroleum based oil.

!WARNING: To avoid injury, ALWAYS turn off and disconnect the Edger from the power outlet BEFORE installing parts or cleaning the Edger or making any adjustments.

!CAUTION: BLADE ROTATES momentarily after power switch is released. Wait for blade to come to a complete stop.

172.79183 specifications

The Sears 172.79183 is a highly regarded model within the realm of consumer electronics, particularly noted for its versatility and user-friendly design. This device is recognized as an essential tool for various applications, combining traditional functionality with modern technologies to cater to an expanding audience of users.

One of the main features of the Sears 172.79183 is its robust build quality. Designed with durability in mind, it can withstand the rigors of daily use, making it suitable for both personal and professional applications. The ergonomic design adds to user comfort, allowing for extended use without causing strain. This focus on user experience is complemented by a sleek and modern aesthetic that fits seamlessly into any environment.

In terms of technology, the Sears 172.79183 incorporates advanced functionalities that enhance its performance. The device includes intuitive controls, which allow users to easily navigate its various features and settings. Additionally, the inclusion of modern connectivity options, such as Bluetooth and USB ports, allows for effortless integration with other devices and peripherals. This versatility makes it possible for users to expand the device's functionality based on their specific needs.

Another characteristic that sets the Sears 172.79183 apart from competitors is its energy efficiency. Designed to minimize power consumption, it not only represents a cost-effective solution for users but also aligns with environmentally conscious practices. This consideration for sustainability is increasingly important in today’s market, where consumers are looking for products that are both functional and eco-friendly.

Furthermore, the Sears 172.79183 offers an array of accessories and compatible add-ons that allow users to tailor the device to their individual preferences. Whether it be for home entertainment, professional tasks, or leisure activities, this adaptability ensures that the Sears 172.79183 meets a diverse range of user requirements.

In summary, the Sears 172.79183 is a standout model that epitomizes the perfect blend of durability, advanced technology, and user-centric design. Its combination of essential features, modern connectivity options, and energy efficiency makes it a reliable choice for consumers looking for a versatile and effective electronic solution. This model not only addresses current user needs but also anticipates and adapts to future demands, ensuring its relevance in an ever-evolving market.