HOW to Start Your Unit, Operating Position

Engine Choke Lever

ON/STOP

Switch

FULL HALF OFF

HOW TO START YOUR UNIT

WARNING: The trimmer head will turn while starting the engine. Avoid any con- tact with the muffler. A hot muffler can cause serious burns.

STARTING A COLD ENGINE (or a warm engine after running out of fuel)

Starting Position

1.Set unit on a flat surface.

2.Slowly press the primer bulb 6 times.

3.Move choke lever to the FULL CHOKE position.

4.Squeeze the throttle trigger fully and hold through all remaining steps.

Starter Handle

Choke

Lever

8.Once the engine starts, allow it to run 10 seconds, then move the choke lever to the OFF CHOKE position. Allow the unit to run for 30 more seconds at OFF CHOKE before releasing the throttle trig- ger.

NOTE: If engine dies with the choke le- ver in the OFF CHOKE position, move the choke lever to the HALF CHOKE position and pull the rope until engine runs, but no more than 6 pulls.

STARTING A WARM ENGINE

1.Move the choke lever to the HALF CHOKE position.

2.Squeeze and hold the throttle trigger. Keep throttle trigger fully squeezed until the en- gine runs smoothly.

3.Pull starter rope sharply until engine runs, but no more than 5 pulls.

4.Allow engine to run 15 seconds, then move the choke lever to OFF CHOKE.

NOTE: If engine has not started, pull starter rope 5 more pulls. If engine still does not run, it is probably flooded.

STARTING A FLOODED ENGINE

Flooded engines can be started by placing the choke lever in the OFF CHOKE position; then, pull the rope to clear the engine of ex- cess fuel. This could require pulling the starter handle many times depending on how badly the unit is flooded.

If the unit still doesn’t start, refer to TROUBLESHOOTING TABLE or call 1-800-554-6723.

OPERATING INSTRUCTIONS

OPERATING POSITION

ALWAYS WEAR:

Eye Protection

Long Pants

Muffler	Heavy Shoes

Primer Bulb

5.Pull starter rope handle sharply until engine sounds as if it is trying to start, but do not pull rope more than 6 times.

6.As soon as engine sounds as if it is trying to start, move choke lever to HALF CHOKE position.

7.Pull starter rope sharply until engine runs, but no more than 6 pulls.

NOTE: If the engine doesn’t start after 6 pulls (at the HALF CHOKE position), move the choke lever to the FULL CHOKE position and press the primer bulb 6 times. Squeeze and hold the throttle trigger and pull the starter rope 2 more times. Move the choke lever to the HALF CHOKE position and pull the start- er rope until the engine runs, but no more than 6 pulls. If the engine still doesn’t start, it is probably flooded. Proceed to

STARTING A FLOODED ENGINE.

Cut from your right to your left.

WARNING: Always wear eye protec- tion. Never lean over the trimmer head. Rocks or debris can ricochet or be thrown into eyes and face and cause blindness or other serious injury.

Do not run the engine at a higher speed than necessary. The cutting line will cut efficiently when the engine is run at less than full throttle. At lower speeds, there is less engine noise and vibration. The cutting line will last longer and will be less likely to “weld” onto the spool.

Always release the throttle trigger and allow the engine to return to idle speed when not cutting.

To stop engine:

SRelease the throttle trigger.

S Push and release the engine ON/STOP switch.

530163444 specifications

The Weed Eater 530163444 is a versatile and efficient tool designed for tackling various lawn care tasks. Known for its reliability and ease of use, this string trimmer is an excellent choice for homeowners and professionals alike.

One of the standout features of the Weed Eater 530163444 is its lightweight design, making it easy to maneuver around gardens, flower beds, and tight spaces. Weighing significantly less than many other models, it reduces user fatigue, allowing for extended periods of trimming without discomfort.

The trimmer is powered by a robust 25cc two-cycle engine, delivering ample power to slice through tough weeds and grass with ease. This engine is engineered for efficiency, providing a good balance of power and fuel consumption. Additionally, the trimmer utilizes a reliable pull-start ignition system that ensures consistent performance every time.

Equipped with a .065-inch nylon line, the Weed Eater 530163444 offers a superior cutting experience. The dual-line head allows for quick line advancement, ensuring that users can continue working without frequent interruptions. The bump feed feature makes it even more convenient to release additional line as needed with just a tap against the ground.

In terms of ergonomics, the Weed Eater boasts a comfortable grip and adjustable handle. Users can customize the handle's position for optimal control and reduced strain during operation. The trimmer also features a protective shield that helps keep debris at bay, enhancing safety during use.

Another significant characteristic of the Weed Eater 530163444 is its versatility. It is compatible with a variety of attachments, including edging and tilling tools, allowing users to expand its functionality beyond simple trimming. This adaptability makes it a valuable addition to any toolkit.

Overall, the Weed Eater 530163444 combines lightweight design, powerful engine performance, and user-friendly features to deliver effective lawn care solutions. Whether you're trimming pesky weeds or shaping up your garden, this trimmer is designed to meet the needs of both novice and experienced users alike. Its reliability and efficiency make it a trusted choice for maintaining a neat and tidy outdoor space.