Carburetor Adjustment, Seasonal Storage

CARBURETOR ADJUSTMENT

WARNING: Keep others away when making idle speed adjustments. The trimmer head will be spinning during this procedure. Wear your protective equipment and observe all safety precautions.

The carburetor has been carefully set at the factory. Adjustments may be necessary if you notice any of the following conditions:

S Engine will not idle when the throttle is re- leased.

Make adjustments with the unit supported so the cutting attachment is off the ground and will not make contact with any object. Hold the unit by hand while running and making ad- justments. Keep all parts of your body away from the cutting attachment and muffler.

Idle Speed Adjustment

Allow engine to idle. Adjust speed until engine runs without stalling (idle speed too slow).

S Turn idle speed screw clockwise to in- crease engine speed if engine stalls or dies.

STurn idle speed screw counterclockwise to decrease engine speed.

Idle Speed

Screw

Air Filter

Cover

If you require further assistance or are unsure about performing this procedure, contact an authorized service dealer or call 1--800--554--6723.

WARNING: Perform the following steps after each use:

S Allow engine to cool, and secure the unit before storing or transporting.

SStore unit and fuel in a well ventilated area where fuel vapors cannot reach sparks or open flames from water heaters, electric

motors or switches, furnaces, etc.

SStore unit with all guards in place. Position unit so that any sharp object cannot acci-

dentally cause injury.

SStore unit and fuel well out of the reach of children.

SEASONAL STORAGE

Prepare unit for storage at end of season or if it will not be used for 30 days or more.

If your unit is to be stored for a period of time:

SClean the entire unit before lengthy storage. S Store in a clean dry area.

S Lightly oil external metal surfaces.

FUEL SYSTEM

Under FUELING ENGINE in the OPERA- TION section of this manual, see message la- beled IMPORTANT regarding the use of ga- sohol in your engine.

Fuel stabilizer is an acceptable alternative in minimizing the formation of fuel gum deposits during storage. Add stabilizer to the gasoline in the fuel tank or fuel storage container. Fol- low the mix instructions found on stabilizer container. Run engine at least 5 minutes after adding stabilizer.

ENGINE

SRemove spark plug and pour 1 teaspoon of 40:1, 2-cycle engine oil (air cooled) through the spark plug opening. Slowly pull the

starter rope 8 to 10 times to distribute oil.

SReplace spark plug with new one of recom- mended type and heat range.

SClean air filter.

S Check entire unit for loose screws, nuts, and bolts. Replace any damaged, broken, or worn parts.

S At the beginning of the next season, use only fresh fuel having the proper gasoline to oil ratio.

OTHER

SDo not store gasoline from one season to another.

S Replace your gasoline can if it starts to rust.

530163444 specifications

The Weed Eater 530163444 is a versatile and efficient tool designed for tackling various lawn care tasks. Known for its reliability and ease of use, this string trimmer is an excellent choice for homeowners and professionals alike.

One of the standout features of the Weed Eater 530163444 is its lightweight design, making it easy to maneuver around gardens, flower beds, and tight spaces. Weighing significantly less than many other models, it reduces user fatigue, allowing for extended periods of trimming without discomfort.

The trimmer is powered by a robust 25cc two-cycle engine, delivering ample power to slice through tough weeds and grass with ease. This engine is engineered for efficiency, providing a good balance of power and fuel consumption. Additionally, the trimmer utilizes a reliable pull-start ignition system that ensures consistent performance every time.

Equipped with a .065-inch nylon line, the Weed Eater 530163444 offers a superior cutting experience. The dual-line head allows for quick line advancement, ensuring that users can continue working without frequent interruptions. The bump feed feature makes it even more convenient to release additional line as needed with just a tap against the ground.

In terms of ergonomics, the Weed Eater boasts a comfortable grip and adjustable handle. Users can customize the handle's position for optimal control and reduced strain during operation. The trimmer also features a protective shield that helps keep debris at bay, enhancing safety during use.

Another significant characteristic of the Weed Eater 530163444 is its versatility. It is compatible with a variety of attachments, including edging and tilling tools, allowing users to expand its functionality beyond simple trimming. This adaptability makes it a valuable addition to any toolkit.

Overall, the Weed Eater 530163444 combines lightweight design, powerful engine performance, and user-friendly features to deliver effective lawn care solutions. Whether you're trimming pesky weeds or shaping up your garden, this trimmer is designed to meet the needs of both novice and experienced users alike. Its reliability and efficiency make it a trusted choice for maintaining a neat and tidy outdoor space.