Weed Eater 530088134 Setting the Edging Depth, Edging Tips, General Recommendations

Page 7

SKeep you edging path straight by aligning the blade guide rib on the rear of the blade guard with the edge of the sidewalk. Keep all wheels flat on the walkway.

NOTE: If the area to be edged has never been cut or several weeks have passed since the last cut, the first edging should be done at no more than half depth.

Blade

Guide Rib

SAlways work going away from people and solid objects such as walls, large stones,

trees, automobiles, etc.

SBe careful when edging near trees or valu- able plants. The high speed metal blade may cut roots and cause damage to the

plants.

S If the blade stalls, immediately move the unit rearward slightly to allow the blade to restart. If the blade continues to stall, stop the engine, disconnect the spark plug, and inspect for blockage or damage.

SAlways keep the blade area clean. Stop the engine, make sure the blade has complete- ly stopped turning, and disconnect the spark plug before cleaning.

SETTING THE EDGING DEPTH

WARNING: Never attempt to adjust the depth adjusting skid when the engine is running. Always release the throttle trigger, wait until the blade stops turning, move the ON/OFF switch to the OFF position, and dis- connect spark plug before making adjust- ments. Your edger is equipped with several edging depths. The depth used will depend on your personal edging preference and the condition of the area where the edging opera- tion is to be done.

To set the depth:

S Move the depth control lever forward for shallower edging.

SMove the depth control lever backward for deeper edging.

Depth Control Lever

Depth

Adjusting

Skid

Support Arm

When edging, the trigger handle must be raised until the skid rests on the ground. The trigger handle must be held in the raised posi- tion during the entire edging operation to maintain a consistent edging depth.

DEPTH ADJUSTING SKID

The surface of the depth adjusting skid will wear over a period of time. This part is revers- ible to provide a second wear surface.

1.Remove the two mounting screws which hold the skid to the support arm.

2.Rotate the skid 180 degrees.

3.Reinstall the mounting screws.

EDGING TIPS

SInspect unit before each use.

SInspect the area to be cut before each use. S Keep unit in front of your body.

S Cut at full throttle.

S Keep the wheels and skid in contact with the ground.

S Always work going away from others.

WARNING: Disconnect the spark plug before performing maintenance except for carburetor adjustments.

GENERAL RECOMMENDATIONS

The warranty on this unit does not cover items that have been subjected to operator abuse or negligence. To receive full value from the warranty, the operator must maintain unit as instructed in this manual. Various adjust- ments will need to be made periodically to properly maintain your unit.

SOnce each year, replace the spark plug, re- place air filter element and check blade for wear. A new spark plug and a clean/new air filter element assures proper air/fuel mix- ture and helps your engine run better and last longer.

CHECK FOR DAMAGED OR

WORN PARTS

Contact an authorized service dealer for re- placement of damaged or worn parts.

SON/OFF Switch -- Ensure ON/OFF switch functions properly by moving the switch to

the OFF position and assure the engine stops; then restart engine and continue.

SFuel Tank -- Discontinue use of edger if fuel tank shows signs of damage or leaks.

SBlade Guard -- Discontinue use of edger if blade guard is damaged.

CHECK FOR LOOSE

FASTENERS AND PARTS

SBlade nut S Muffler

S Cylinder shield S Clutch

S Throttle trigger S Handle screws S Fasteners

INSPECT AND CLEAN UNIT & LA- BELS

S After each use, inspect complete unit for loose or damaged parts. Clean the unit and labels using a damp cloth with a mild deter- gent.

S Wipe off unit with a clean dry cloth.

7

Image 7
Contents Manual de Instrucciones Manuel d’Instructions Justments Operator SafetyUnit Safety Edging SafetySpecial Fuel SafetyTransporting and Storage Adjustable wrench Hex wrench provided Tube AssemblyStarter Rope Handle ON/OFF SwitchDepth Adjusting Skid Know Your EdgerStarting a Flooded Engine Stopping Your EngineStarting Your Engine Starting a Warm EngineGeneral Recommendations Setting the Edging DepthInspect and Clean Unit & LA- Bels Edging TipsReplace Spark Plug Clean AIR FilterBlade Maintenance Blade Replacement Carburetor AdjustmentsOther Seasonal StorageFuel System EngineTroubleshooting Table Cause Remedy Agency and POULAN/WEED EATER, Divi Electrolux Home PRODUCTS, INC