HOW to Start Your Unit, Operating Position

Engine Choke Lever

ON/OFF

Switch

FULL HALF OFF

HOW TO START YOUR UNIT

WARNING: The trimmer head will turn while starting the engine. Avoid any con- tact with the muffler. A hot muffler can cause serious burns.

STARTING A COLD ENGINE (or a warm engine after running out of fuel)

Starting Position

1.Set unit on a flat surface.

2.Move ON/OFF switch to the ON position.

3.Slowly press the primer bulb 6 times.

4.Move choke lever to the FULL CHOKE position.

5.Squeeze the throttle trigger fully and hold through all remaining steps.

Starter Handle

Choke

Lever

Muffler

Primer Bulb

9.Once the engine starts, allow it to run 10 seconds, then move the choke lever to the OFF CHOKE position. Allow the unit to run for 30 more seconds at OFF CHOKE before releasing the throttle trig- ger.

NOTE: If engine dies with the choke le- ver in the OFF CHOKE position, move the choke lever to the HALF CHOKE position and pull the rope until engine runs, but no more than 6 pulls.

STARTING A WARM ENGINE

1.Move ON/OFF switch to the ON position.

2.Move the choke lever to the HALF CHOKE position.

3.Squeeze and hold the throttle trigger. Keep throttle trigger fully squeezed until the en- gine runs smoothly.

4.Pull starter rope sharply until engine runs, but no more than 5 pulls.

5.Allow engine to run 15 seconds, then move the choke lever to OFF CHOKE.

NOTE: If engine has not started, pull starter rope 5 more pulls. If engine still does not run, it is probably flooded.

STARTING A FLOODED ENGINE

Flooded engines can be started by placing the choke lever in the OFF CHOKE position; then, pull the rope to clear the engine of ex- cess fuel. This could require pulling the starter handle many times depending on how badly the unit is flooded.

If the unit still doesn’t start, refer to TROUBLESHOOTING TABLE or call 1-800-554-6723.

OPERATING INSTRUCTIONS

OPERATING POSITION

ALWAYS WEAR:

Eye Protection

Long Pants

Heavy Shoes

6.Pull starter rope handle sharply until engine sounds as if it is trying to start, but do not pull rope more than 6 times.

7.As soon as engine sounds as if it is trying to start, move choke lever to HALF CHOKE position.

8.Pull starter rope sharply until engine runs, but no more than 6 pulls.

NOTE: If the engine doesn’t start after 6 pulls (at the HALF CHOKE position), move the choke lever to the FULL CHOKE position and press the primer bulb 6 times. Squeeze and hold the throttle trigger and pull the starter rope 2 more times. Move the choke lever to the HALF CHOKE position and pull the start- er rope until the engine runs, but no more than 6 pulls. If the engine still doesn’t start, it is probably flooded. Proceed to

STARTING A FLOODED ENGINE.

Cut from your right to your left.

WARNING: Always wear eye protec- tion. Never lean over the trimmer head. Rocks or debris can ricochet or be thrown into eyes and face and cause blindness or other serious injury.

Do not run the engine at a higher speed than necessary. The cutting line will cut efficiently when the engine is run at less than full throttle. At lower speeds, there is less engine noise and vibration. The cutting line will last longer and will be less likely to “weld” onto the spool.

Always release the throttle trigger and allow the engine to return to idle speed when not cutting. To stop engine:

SRelease the throttle trigger.

SMove the ON/OFF switch to the OFF posi- tion.

530163439 specifications

The Weed Eater 530163439 is a powerful and reliable solution for anyone looking to maintain their lawn and garden with ease. This trimmer is designed with a focus on performance and user comfort, making it an indispensable tool for homeowners and landscapers alike.

One of the standout features of the Weed Eater 530163439 is its advanced gas-powered engine. The powerful two-stroke engine delivers ample cutting power, allowing users to tackle even the toughest weeds and overgrown areas. This engine is designed for performance and durability, ensuring that it can handle regular use without compromising on power or efficiency.

In addition to its robust engine, the Weed Eater 530163439 is equipped with a long, flexible shaft that provides excellent reach and maneuverability. This design allows users to easily access hard-to-reach areas, such as beneath bushes or along fences, without straining their backs or arms. The ergonomic handle is another user-friendly feature, providing comfort and control during extended periods of operation.

This trimmer also incorporates a reliable bump feed line advance system, which simplifies the process of feeding new line when needed. With this system, users can easily release more line by tapping the trimmer head on the ground, ensuring continuous cutting without interruption. The dual-line cutting head enhances productivity, allowing for a wider cutting path and more efficient trimming.

Moreover, the Weed Eater 530163439 is built with durability in mind. Its robust construction ensures that it can withstand the rigors of outdoor use, from residential lawns to commercial landscaping projects. Additionally, the lightweight design makes it easy to carry and operate for extended periods without fatigue.

Another technological highlight of the Weed Eater 530163439 is its fuel efficiency. The engine is designed to optimize fuel consumption while maintaining powerful performance, allowing users to work longer without frequent refueling. This efficient operation reduces downtime and increases productivity, making it a smart choice for those serious about lawn care.

In conclusion, the Weed Eater 530163439 combines power, ease of use, and durability to deliver an exceptional lawn care experience. With its advanced engine, flexible shaft, and user-friendly features, this weed trimmer is ideal for anyone looking to keep their outdoor spaces neat and tidy with minimal effort.