Troy-Bilt V560 manual Blade Care, Belt Care

Page 11

Blade Care

WARNING: When removing cutting blade for sharpening or replacement, protect your hands with a pair of heavy gloves or use a heavy rag to hold blade.

1.Disconnect spark plug wire from spark plug. Turn mower on its side making sure that the air filter and the carburetor are up.

2.Remove bolt, blade bell support, blade, and blade adapter from the engine crankshaft. See Figure 5-3.

3.The blade can be sharpened with a file or on a grind- ing wheel. Do not attempt to sharpen the blade while it is still on the mower. When sharpening blade, follow original angle of grind. Grind cutting edges equally to keep blade balanced.

4.Remove blade from the adapter for testing balance. Balance the blade on a round shaft screwdriver to check. Remove metal from the heavy side until it balances evenly.

WARNING: An unbalanced blade will cause excessive vibration when rotating at high speeds. It may cause damage to mower, and could break causing personal injury.

5.Lubricate the engine crankshaft and the inner surface of the blade adapter with light oil. Slide the blade adapter onto the engine crankshaft. Place the blade on the adapter such that the side of the blade marked “Bottom” (or with part number) faces the ground when the mower is in the operating position. Make sure that blade is aligned and seated on blade adapter flanges.

6.Place blade bell support on the blade. Align notches on the blade bell support with small holes in blade. Replace hex bolt and tighten hex bolt to torque: 450 in. lbs. min., 600 in. lbs. max.

To ensure safe operation of your mower, periodically check the blade bolt for correct torque.

Figure 5-3

1

2

3

Figure 5-4

5

Maintaining

Your Lawn

Mower

WARNING

When removing the cutting blade for sharpening or replacement or when sliding the belt around it, protect your hands with a pair of heavy gloves or use a heavy rag to hold the blade.

An unbalanced blade will cause excessive vibration when rotat-

Belt Care

1.Remove two shoulder screws securing front drive cover to mower deck. See Figure 5-4. Press inward on sides of front drive cover and release tabs that secure it to the height adjuster brackets. Remove drive cover from mower.

2.Pull up on the belt keeper wire and pivot it out away from the drive pulley. See Figure 5-4 inset.

3.Roll the belt off the transmission pulley. Tip mower on its side with the air filter up to access belt from underside of mower. Slide belt off of engine pulley and thread through the opening in the belt keeper bracket. Then remove the belt from around the blade by remov- ing over one end at a time. See Figure 5-5.

Figure 5-5

4.Replace with new belt, working around blade and up through the belt keeper bracket. Make sure belt is firmly seated on engine pulley while pulling from the other side and sliding it around the transmis- sion pulley. Pivot the belt keeper wire back into its operating position and snap into the slot provided. Reassemble front drive cover.

ing at high speeds. It may cause damage to mower, and could break causing per- sonal injury.

11

Image 11
Contents 07/2007 Inch Self-Propelled Mulching Mower Model SeriesCustomer Support Table of ContentsFinding and Recording Model Number Slope Gauge Your Responsibility Safe Operation PracticesUse only an approved gasoline container Slope OperationSetup Adjustment Firmly against top Grass catcher AdjustmentsCutting Height Drive ControlKnow Your Lawn Mower Starting Engine Using Your Lawn MowerUsing as Mulcher Using Grass CatcherMaintaining Your Lawn Mower Belt Care Blade CareEngine overheats Trouble ShootingProblem Cause Remedy Off-Season Storage Off Season Storage Safety LabelsSafety Labels Found On Your Lawn Mower WaveTread 20 21For parts and/or Accessories Please call Parts ListModel Series 748-04015A†† One Piece Blade AdapterMANUFACTURER’S Limited Warranty for Podadora tipo abonadora autopropulsada de Modelo Serie Manual DEL OperadorNúmero de modelo Número de serie ÍndiceBúsqueda y registro del número de modelo Asistencia al clienteIndica- dor de pendien- te Funcionamiento general ResponsabilidadCuando vea este símbolo Manejo seguro de la gasolinaNo haga lo siguiente Funcionamiento en pendientesHaga lo siguiente Superior Soldado a cada lado de la manija inferiorHardware Guía de la cuerdaNunca opere la AdvertenciaClavija para abono Mantenga sus manosControl de cuchilla Control de la transmisiónUso de la podadora de césped Encendido del motor Briggs & Stratton/ TecumsehHonda Detención del motorCuidados para el motor Recomendaciones generalesLubricación Cuidado de la cubiertaCuando saque la Cuchilla para afilarla Cuidado de la cuchillaCuidado de la correa El motor recalienta Solución de ProblemasProblema Causa Remedio Almacenamiento fuera de temporada SeguridadGastos de transporte y llamadas por servicios técnicos Esta garantía limitada no lo cubrirá en los siguientes casos