Troy-Bilt GT54 manual Battery, Cutting Deck Removal

Page 21

balanced blade will cause excessive vibration and may cause damage to the tractor and result in personal injury.

IMPORTANT:When replacing the blade, be sure to install the blade with the side of the blade marked ‘‘Bottom’’ (or with a part number stamped in it) facing the ground when the mower is in the operating position.

IMPORTANT:Use a torque wrench to tighten the blade spindle hex flange nut to between 70 lbs-ft and 90 lbs-ft.

Battery

The battery is sealed and is maintenance-free. Acid levels cannot be checked and fluid can not be added.

•Always keep the battery cables and terminals clean and free of corrosive build-up.

•After cleaning the battery and terminals, apply a light coat of petroleum jelly or grease to both terminals

•Always keep the rubber boot positioned over the positive terminal to prevent shorting.

IMPORTANT: If removing the battery, disconnect the NEGATIVE (Black) wire from it’s terminal first, followed by the POSITIVE (Red) wire. When re-installing the battery, always connect the POSITIVE (Red) wire its terminal first, followed by the NEGATIVE (Black) wire. Be certain that the wires are connected to the correct terminals; reversing them could change the polarity and cause damage to your engine’s alternating system.

Jump Starting

WARNING: Never jump start a damaged or frozen battery. Be certain the vehicles do not touch, and ignitions are off. Do not allow cable clamps to touch.

•Connect positive (+) cable to positive post (+) of your tractor’s discharged battery.

•Connect the other end of the cable to the (positive +) post of the jumper battery.

•Connect the second cable (negative –) to the other post of the jumper battery.

•Make the final connection on the engine block of the stalled tractor, away from the battery. Attach to a unpainted part to assure a good connection.

IMPORTANT: If the jumper battery is installed on a vehicle (i.e. car, truck), do NOT start the vehicle’s engine when jump starting your tractor.

•Start the tractor (as instructed on page 14).

•Set the tractor’s parking brake before removing the jumper cables, in reverse order of connection.

•Allow the tractor’s engine to run for 15 minutes before shutting it off to allow the alternating system time to charge the discharged battery.

Charging

If the unit has not been put into use for an extended period of time, charge the battery with an automotive-type 12-volt charger for a minimum of one hour at six amps.

WARNING: Batteries give off an explosive gas while charging. Charge battery in a well ventilated area and keep away from an open flame or pilot light as on a water heater, space heater, furnace, clothes dryer or other gas appliances.

Cutting Deck Removal

To remove the cutting deck, proceed as follows:

•Place the PTO/Blade Engage knob in the disengaged (OFF) position and engage the parking brake.

•Lower the deck by moving the deck lift lever into the bottom notch on the right fender.

•Remove the deck belt from around the tractor’s electric PTO clutch (refer to Changing the Deck Belt).

•Looking at the cutting deck from the left side of the tractor, locate the deck support pin on the rear left side of the deck.

•Rotate the pin slightly toward the rear of the tractor and release the pin into the hole provided.

•Pull the deck support pin outward to release the deck from the deck lift arm. See Figure 16.

Support Pin

Figure 16

•Repeat the above steps on the tractor’s right side.

•Move the deck lift lever into the top notch to raise the deck lift arms up and out of the way.

21

Page 20 Page 22
Image 21
Page 20 Page 22
Contents Operator’s Manual Table of Contents General Operation Important Safe Operation PracticesSlope Operation Towing Page Slope Gauge Tire Pressure Attaching the Battery CablesShipping Brace Removal Gas and Oil Fill-upSetting the Gauge Wheels and Roller Know Your Garden Tractor Seat Adjustment Lever Ignition Switch ModuleChoke Control Brake PedalElectric PTO Blade Engage Knob Cruise Control LeverParking Brake Lever Safety Interlock Switches Reverse Caution ModeOperating Your Garden Tractor Stopping the Engine Starting the EngineEngaging the Parking Brake Driving The TractorUsing the Deck Lift Lever Setting The Cruise ControlDriving On Slopes Operating the HeadlightsMowing Engaging the PTOLeveling the Deck Making AdjustmentsParking Brake Adjustment Steering AdjustmentSeat Adjustment Maintaining Your Garden Tractor Cleaning the Engine and DeckEngine LubricationTires ServiceFuse Cutting BladesCutting Deck Removal BatteryChanging the Deck Belt OFF-SEASON Storage Trouble Possible Causes Corrective Action TroubleshootingAttachments Attachments & AccessoriesParts List for Model GT54 Model GT54 54 2 Model GT54 Model GT54 711-1409A Model GT54 † not pictured 3010 829 Interlock Switch 45C 6710 731-3005 For Choke MANUFACTURER’S Warranty Coverage MTD LLC, P.O. BOX 361131 CLEVELAND, Ohio 44136-0019 Phone

GT54 specifications

The Troy-Bilt GT54 is a versatile lawn tractor designed to provide homeowners with a powerful and efficient means of maintaining their gardens and lawns. With an emphasis on comfort, durability, and advanced technology, the GT54 stands out in the competitive market of riding lawn mowers.

Starting with its robust engine, the GT54 is equipped with a reliable 54-inch deck powered by a high-performance engine, often a 24 HP Kohler V-Twin. This engine not only offers considerable power but also ensures smooth operation and durability, making it suitable for a variety of terrains and cutting conditions. With the capability to tackle tough weeds and thick grass, the GT54 is perfect for medium to large yards.

One of the most significant features of the GT54 is its innovative cutting system. The tractor boasts a cutting deck that allows for 5 different height adjustments, making it easy to achieve the desired grass length. The twin-blade system combined with the deck's airflow design ensures that grass clippings are efficiently dispersed, providing a clean, even cut that can enhance the health of your lawn.

Comfort is a priority with the GT54, featuring an ergonomic seat designed for extended use, which reduces fatigue during longer mowing sessions. The steering wheel is positioned for easy maneuverability, allowing users to navigate tight corners and obstacles effortlessly.

The GT54 is also equipped with various technological advancements, including a fast and responsive automatic transmission that allows for easy speed adjustments. This feature gives homeowners greater control when mowing, particularly in challenging areas. Additionally, the electric PTO (Power Take-Off) makes engaging the mower deck straightforward, simplifying the mowing process even further.

For those looking to extend the functionality of their lawn tractor, the GT54 is compatible with various attachments, such as baggers, plows, and spreaders, making it a year-round tool for landscape maintenance. Its durable steel construction ensures longevity, making the GT54 a reliable investment for landscape enthusiasts.

In summary, the Troy-Bilt GT54 combines power, versatility, and user-friendly features. With its efficient cutting system, commitment to comfort, and advanced technological elements, this lawn tractor is designed to meet the needs of homeowners seeking to maintain their outdoor spaces with ease and precision. Whether one is a casual user or a dedicated landscaper, the GT54 is equipped to handle various chores efficiently.
Top Page Image Contents