Troy-Bilt 204 warranty Sharpening Or Replacing Chipper Blades, Remove and set aside the vacuum bag

Page 11

3.Remove and set aside the vacuum bag.

4.a. Remove the four self-tapping screws from the bottom of the discharge chute. See Figure 5-3.

b.Remove the hex bolt, saddle washer and hex nut from the top and remove the discharge chute assembly. See Figure 5-3.

5.a. Remove the two hex bolts and hex nuts which extend through the impeller housing.

b.Lift the flail screen from inside the housing. See Figure 5-4.

6.Clean the flail screen by scraping and/or washing with water, and reinstall the screen.

NOTE: Be certain to reassemble the flail screen with the curved side down.

7.Reattach the discharge chute assembly with the hardware previously removed and attach the bag to the unit.

Sharpening Or Replacing Chipper Blades

NOTE: When tipping the unit, empty the fuel tank and keep engine spark plug side up.

1.Disconnect spark plug wire and ground it against engine.

2.Remove flail screen as instructed in previous section.

3.a. Remove plastic belt cover from front of the engine by removing the two self-tapping screws. See Figure 5-5 on next page.

b.Remove the access plate by removing two hex lock nuts.

c.Locate one of the chipper blades in the access opening by rotating the impeller assembly by hand. Remove the chipper blade using a 3/16” allen wrench and a 1/2” wrench. See Figure 5-5.

4.Remove other blade in the same manner to replace or sharpen.

WARNING: Use caution when replacing the blades. Wear heavy gloves to avoid injury while handling the weld bolts, housing or the blades.

NOTE: When sharpening blades, follow the original angle of grind. Also, make sure to remove an equal amount from each blade and torque hardware to 250 - 300 in.lb.

IMPORTANT: Make sure that blades are reassembled with the sharp edge facing upward.

Tire Pressure (Pneumatic tires only)

Maximum tire pressure under any circumstance is 30 psi. Equal tire pressure should be maintained at all times. assembly.

B

5

A

Maintaining

 

 

Your

A

Chipper

 

Shredder

 

Vacuum

Figure 5-3

 

B

 

 

WARNING

 

Use caution when re-

A

placing the blades. Wear

heavy gloves to avoid

 

injury while handling the

 

weld bolts, housing or

 

the blades.

 

Figure 5-4

A

NOTE: Be certain to

reassemble the flail

 

C

screen with the curved

 

side down.

 

NOTE: When sharpen-

B

ing blades, follow the

original angle of grind.

 

Also, make sure to re-

 

move an equal amount

 

from each blade and

 

torque hardware to 250

Figure 5-5

- 300 in.lb.

 

11

Page 10 Page 12
Image 11
Page 10 Page 12
Contents Chipper Shredder Vacuum Model OPERATOR’S ManualCustomer Support Table of ContentsFinding and Recording Model Number Page Safe Operation Safe Operation Practices Attaching The Chipper Chute Setting Up Your Chipper Shredder VacuumLoose Parts In Carton Attaching The NozzleAttaching The Bag Know Your Chipper Shredder Vacuum Stopping The Engine Using the Chipper Shredder VacuumGas and Oil Fill-Up Starting EngineMaintaining Your Chipper Shredder Vacuum Remove and set aside the vacuum bag Sharpening Or Replacing Chipper BladesProblem Cause Remedy Trouble ShootingStoring Your Yard Vacuum OffModel To order replacement Parts, contact Or visit Parts ListModel Chain Case LH Page Page MANUFACTURER’S Limited Warranty for
Related manuals
Manual 15 pages 5.08 Kb

204 specifications

The Troy-Bilt 204 is a versatile and dependable tool designed for homeowners and garden enthusiasts who require efficient yard care solutions. This tiller is designed to break new ground, cultivate existing garden beds, and create beautifully tilled soil in a variety of terrains. The Troy-Bilt 204 boasts a series of advanced features, making it a reliable choice for both novice and experienced gardeners.

One standout feature of the Troy-Bilt 204 is its powerful engine. Equipped with a robust 4-cycle engine that delivers ample horsepower, this tiller strikes a perfect balance between strength and efficiency. With easy starting capabilities and low maintenance needs, users can focus more on tilling rather than wrestling with equipment.

The tiller's tilling width and depth are adjustable, allowing users to customize their experience based on specific garden needs. The 12-inch tilling width covers a substantial area quickly, while the adjustable depth helps in aerating the soil effectively, promoting better plant growth. The Troy-Bilt 204 also features a set of dual rotating tines that enhance its tilling capabilities. These durable tines are designed to penetrate tough soil, making it ideal for a wide range of gardening tasks.

Another noteworthy aspect of the Troy-Bilt 204 is its maneuverability. The tiller is designed with a lightweight construction and a comfortable handle, making it easy to navigate through gardens and flower beds. The unit also includes a depth stake that provides added control and stability, ensuring consistent and even tilling.

Safety and durability are paramount in the design of the Troy-Bilt 204. The tiller features protective shields that keep debris at bay while ensuring the operator remains safe during use. Additionally, its robust construction promises longevity, allowing homeowners to tackle years of gardening projects without worry.

In summary, the Troy-Bilt 204 stands out in the gardening tool market for its powerful performance, adjustable features, and exceptional durability. Its combination of advanced technologies ensures that it meets the demands of various gardening tasks, making it a valuable asset for anyone looking to cultivate a lush garden. With the Troy-Bilt 204, gardening becomes a more efficient and enjoyable experience, paving the way for green thumbs everywhere.
Top Page Image Contents