White Outdoor Z-185L, Z-205, Z-225 manual Lubrication, Oil Check Change Capacity Type

Page 19

16.Remove quarter inch by seven inch pins from top and bottom holes.

17.Set parking brake and start the engine (set throttle at full speed). Make sure that the PTO is off.

18.Rotate rods (lengthen or shorten) to bring each hydrostat to neutral.

NOTE: The control linkage going to the hydrostatic pump has left-hand threads at the pump and right-hand threads at the tower.

19.Tighten the jam nuts earlier loosened.

20.Reassemble safety switches.

21.Reassemble body panels.

22.Reassemble drive handle assembly.

23.Make sure that all hardware is tightened.

SECTION 7: LUBRICATION

Use the two tables that follow for lubrication details. The first table is for oil details and the second table is for grease point information.

Oil

Check

 

Change

 

Capacity

Type

 

 

 

 

 

 

 

 

 

 

 

Engine crankcase

See Engine Operator’s Manual Section

 

 

 

 

 

 

 

 

 

 

 

 

Hydraulic units

50 Hours

 

500 Hours

 

9.5 Quarts

Part Number 737-0305 (10W40 motor oil)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Grease Point

 

 

When to Grease

Type of Grease

 

 

 

 

 

 

 

 

Caster Ass’y - 3 fittings (1 on each

 

50 Hours

Two strokes (minimum) of lubricator using 251 H EP grease or

 

wheel spindle and one on middle of

 

 

 

equivalent No. 2 multipurpose lithium grease (refer to

GREASE

 

caster assembly)

 

 

 

 

POINT LOCATIONS on page 20 for locations)

 

 

 

 

 

 

 

Caster wheels - 2 fittings (1 on each

 

50 Hours

Two strokes (minimum) of lubricator using 251 H EP grease or

 

wheel)

 

 

 

 

equivalent No. 2 multipurpose lithium grease (refer to

GREASE

 

 

 

 

 

 

POINT LOCATIONS on page 20 for locations)

 

 

 

 

 

 

 

 

Control Tower - 2 fittings

 

 

50 Hours

Two strokes (minimum) of lubricator using 251 H EP grease or

 

(Right side of tower)

 

 

 

 

equivalent No. 2 multipurpose lithium grease (refer to

GREASE

 

 

 

 

 

 

POINT LOCATIONS on page 20 for locations)

 

 

 

 

 

 

 

 

Deck Lift Pivot

 

 

50 Hours

Two strokes (minimum) of lubricator using 251 H EP grease or

 

 

 

 

 

 

equivalent No. 2 multipurpose lithium grease (refer to

GREASE

 

 

 

 

 

 

POINT LOCATIONS on page 20 for locations)

 

 

 

 

 

 

 

 

Lift Handle

 

 

50 Hours

Two strokes (minimum) of lubricator using 251 H EP grease or

 

 

 

 

 

 

equivalent No. 2 multipurpose lithium grease (refer to

GREASE

 

 

 

 

 

 

POINT LOCATIONS on page 20 for locations)

 

 

 

 

 

 

 

 

Mower Deck

 

 

50 Hours

Two strokes (minimum) of lubricator using 251 H EP grease or

 

 

 

 

 

 

equivalent No. 2 multipurpose lithium grease (refer to

GREASE

 

 

 

 

 

 

POINT LOCATIONS on page 20 for locations)

 

 

 

 

 

 

 

 

 

 

 

 

19

Image 19
Contents OPERATOR’S Manual Important Read Safety Rules and Instructions CarefullyFinding Your Model Number Calling Warranty ServiceGeneral Operation Important Safe Operation PracticesChildren ServiceSlope Operation Do notSafety Labels Found On Unit Slope Gauge Controls IGNITION/LIGHT SwitchHOUR/RPM Meter Throttle Lever Lift HandleThrottle Lever and Choke Lever Front Choke LeverBrake Pedal Power TAKE-OFF PTO SwitchParking Brake Pedal Speed Control BAR Drive HandlesSeat Adjustment Lever Indicator PanelStopping the Z-SERIES OperationBefore Operating Operating GuidelinesDriving the Z-SERIES Starting a Flooded EngineDriving on Slopes Quick Reference Chart Avoid Streaking MowingPushing Your Unit Checking the Brake Adjustment Adjustments Adjusting the Mower Deck Height Adjusting the Seat PositionSteering Adjustment Adjusting Brake ForceJam Nuts Oil Check Change Capacity Type LubricationGrease Point Locations Checking Hydraulic OIL Level MaintenanceEngine Compartment Fuel TankDraining Hydraulic OIL Adding Hydraulic OILChanging the Fuse Battery MaintenanceCharging the Battery Replacing the Head Lamp BulbCleaning the Battery Removing the BatteryInstalling the Battery Jump Starting the BatteryLeveling the Mower Deck Mower DecksWhen either side is lower than Removing the Mower Deck Installing a NEW Mower Deck Belt Mower Deck Belt Routing Installing the Mower DeckLubrication of Mower Deck Installing a BladeCutting Blade Care Removing a BladeStorage Installing a NEW Drive BeltTrouble Possible Causes Corrective Action Trouble Shooting GuidePage Page Page Page Page MANUFACTURER’S Limited Warranty for