Mounting and Wiring Instructions

CAUTION: For fixtures labeled for outdoor and wet location use, provide a water-tight seal between the fixture and the mounting surface by using silicone or similar caulking.

NOTE: Underwriters Laboratories (UL) does not require all fixtures to have ground wires. These fixtures meet all UL specifications.

1.Turn off power at circuit box to avoid possible electric shock.

2.Thread mounting screws (A) into the universal mounting plate or cross bar (B) (see fig. 1).

3.Secure universal mounting plate or cross bar (B) to outlet box (C) with outlet box screws (D) (not included).

NOTE: Mounting screws (A) must be level for fixture to hang straight.

4.Identify color coding of fixture wires (see fig. 2).

5.To connect wires, take black fixture wire (group A from fig. 2) and place evenly against black outlet box wire. Do not twist wires.

6.Fit wire connector (H) (see fig. 2) over wires and twist until there is a firm connection. If wire connector (H) easily comes off, reattach and check again for a firm connection.

7.Repeat steps 7 and 8 with the white (group B from fig. 2) fixture wires and outlet box wires.

8.Partially thread green grounding screw (I) into side hole (J) on universal mounting plate or cross bar (B) (see fig. 1).

9.Wrap ground wire from fixture around green grounding screw (I) leaving enough excess wire to then connect ground wire and outlet box wire with wire connector (H), if applicable.

10.Tighten green grounding screw (I). Do not over tighten.

11.Tuckwires inside outlet box (C).

FIXTURE ASSEMBLY INSTRUCTIONS

1.Place back plate (K) over mounting screws (A) and mounting nipple (F) (see fig. 1).

2.Secure into place with small cap nuts (L).

3.Open hinged door (N). Install socket cover(s) (O), if applicable.

4.Install lamp(s). Do not exceed recommended wattage.

5.Close hinged door (N).

6.Turn power back on at circuit box.

W-125 specifications

The Westinghouse W-125 is a notable power generation turbine designed for the modern energy landscape, integrating advanced technologies that enhance its efficiency and reliability. Developed by Westinghouse Electric Corporation, this turbine exemplifies cutting-edge engineering, emphasizing performance and sustainability in power generation.

At the heart of the W-125's design is its high-efficiency combustion system. By employing advanced fuel injection technologies, the turbine optimizes the air-fuel mix, resulting in improved combustion efficiency. This not only leads to higher output but also reduces emissions, aligning with global environmental standards. The W-125 is capable of operating on a variety of fuels, including natural gas and light distillates, providing flexibility for power producers.

The turbine’s aerodynamic design significantly contributes to its performance metrics. With its optimized rotor and stator configurations, the W-125 minimizes aerodynamic losses, thereby maximizing the energy extracted from the combustion process. This feature is crucial for power plants aiming to increase their output while maintaining operational costs.

One of the standout characteristics of the W-125 is its modular design. This allows for easier maintenance and upgrades, enabling operators to implement technological advancements as they become available without needing to replace the entire system. This flexibility is particularly valuable in today’s rapidly evolving energy market, where adaptation is essential for competitiveness and efficiency.

The control systems integrated into the W-125 are state-of-the-art, employing advanced algorithms for real-time monitoring and optimization. This ensures that the turbine operates at peak efficiency under varying load conditions, making it an ideal choice for both baseload and peak load applications. Additionally, the turbine is equipped with advanced diagnostic tools, which facilitate predictive maintenance and reduce downtime.

Noise reduction technologies have also been considered in the W-125’s design. With sound-dampening features, the turbine operates quietly, minimizing its environmental impact, which is crucial for installations near populated areas.

Overall, the Westinghouse W-125 stands out with its combination of efficiency, flexibility, and advanced technologies. It represents a significant step forward in turbine design, catering to the demands of modern energy production while promoting sustainability and economic viability. As energy needs continue to evolve globally, the W-125 is poised to play a crucial role in shaping the future of power generation.