Woods Equipment 872502G, MZ2661K, 872500G manual Check Daily, Battery

Page 10

MAINTENANCE

CHECK DAILY

WOODS

Operator Presence Interlock System - Start Operation

For the engine to crank, the parking brake must be on, the PTO (blades) off and traction levers in the neutral lock position. Sit in the seat and check, one by one, if the engine will crank with the parking brake off, the blades on, and either traction lever out of neutral lock. Also, make sure engine coolant temperature gauge light flashes upon turning key to the ON position.

Operator Presence Interlock System - Run Operation

The operator must be in the seat for the engine to run with the parking brake off, the traction levers moved out of the neutral lock position, or the blades on. To check:

1.Start the engine and run at 1/2 throttle with the operator on the machine but raised off the seat.

2.One by one: move the parking brake to the OFF position, traction levers out of the neutral lock position (check each independently), and turn the blades on. Each check should kill the engine after 1/2 second. (A 1/2 second delay is built into the system to prevent engine cutout when traversing rough terrain.)

Repair machine before using if the Operator Presence Interlock System does not operate correctly in start or run. Contact your authorized BOB-CAT dealer.

Hardware

Tighten any nuts and bolts found loose. Replace any broken or missing cotter pins. Repair any other problems before operating.

Tire pressure

Rear tires should be kept inflated at 12 lbs/in2 (1.0 kg/cm2). Improper tire inflation can cause rapid tire wear and poor traction. Uneven inflation can cause uneven cutting.

BATTERY

Battery acid is caustic and fumes are explosive and can cause serious injury or death.

Use insulated tools, wear protective glasses or goggles and protective clothing when working with batteries. Read and obey the battery manufacturer’s instructions.

Be certain the ignition switch is OFF and the key has been removed before servicing the battery.

1.Verify battery polarity before connecting or dis- connecting the battery cables.

2.When installing the battery, always assemble the RED, positive ( + ) battery cable first and the ground, BLACK, negative ( - ) cable last.

3.When removing the battery, always remove the ground, negative ( - ) cable first and the red, posi- tive ( + ) cable last.

4.Check the electrolyte level every 100 hours of operation.

5.Clean the cable ends and battery posts with steel wool. Use a solution of baking soda and water to clean the battery. Do not allow the solution to enter into the battery cells.

6.Tighten cables securely to battery terminals and apply a light coat of silicone dielectric grease to terminals and cable ends to prevent corrosion.

Keep terminal covers in place.

10

Page 9 Page 11
Image 10
Page 9 Page 11
Contents MOW’N Machine ArevCalifornia Wash Hands After HandlingTo the Owner Important MessageTo the Dealer Alitec BMP Central Fabricators Gannon Gill WAIN-ROY WoodsTable of Contents Safety Become AlertUncrate Unit Tools Required for AssemblyDeck Leveling Counterbalance Springs Final PreparationsMachine EngineHydraulics First Every DailyMaintenance Record Battery Check DailyLubrication After First Five 5 Hours Hydraulic SystemPeriodic OIL Changes Engine OIL Spark PlugsFuel Filter Heavy Duty Cyclonic AIR CleanerEngine Cooling Cleaning Machine Washing MachineSharpening Blade InstallationBlade Removal Blade BalanceAdjustments Deck LevelingRear Deck Rollers Height of CUTCounterbalance Springs Control Levers Parking BrakeDampers Tracking HandlesFront Deck LIP Hydrostat Adjustments NeutralCutterdeck Belt PUMP-DRIVE BeltDrive System WeightEngines Operator Presence Interlock SystemEngines Check Tire Pressures Lubricate All Points Check Nuts & Bolts Spindles ConstructionCutterdeck Drive System ANTI-SCALP RollersParts Section Upper Engine Deck Assy Description QTY Not IllustratedLower Engine Deck ASSY/CLUTCH Description QTY Item Part no LOCKWSHR-3/8 HelicalBumper Item Part no Description QTY Item Part no Fuel TANKS/CONTROL Panel TANK-FUEL LH BRAKES/REAR Wheel WLDMT-BRAKE ARM LH OIL Cooler BRKT-COOLER Front AIR Cooled Hydraulics Item Part no Description QTY SAE Port O RingHydrogear Pump Hydrogear Part no Woods Part no Description QTY AIR Cooled Wire Harness HARNESS-WIRING Main Seat Assembly SEAT-SUSPENSION Includes Items 2-12 Optional Folding Rops KIT PIN-HITCH 1/2 STEERING/DECK Lift Spring Cradle Assembly LABEL-WARNING Cradle & Caster Assembly CUP, Outer Bearing Torque to 70 FT-LBS Deck W/ Labels 52 ZT2 3233 Deck W/ Labels 61 ZT2 BELTS-CUTTERDECK BELT-CUTTERDECK DECALS-POWER Unit LABEL-MZ DECALS-CUTTERDECKS LABEL-WARNING Blades Limited Warranty 8495 MM & Boundary Repair Parts Rev /15/2006 Woods Equipment Company

872500G, 872502G, MZ2661K specifications

Woods Equipment is a renowned name in the agricultural and landscaping industry, known for its high-quality attachments and machinery designed for a variety of applications. Among its impressive lineup are the MZ2661K, 872502G, and 872500G models, each catering to specific needs and offering various advanced features and technologies.

The Woods MZ2661K is a robust equipment piece known for its versatility and reliability. It features a powerful engine that provides excellent performance in various terrain conditions. The MZ2661K includes a heavy-duty frame designed to withstand rigorous use, making it suitable for both commercial and residential landscaping needs. Its user-friendly interface allows operators to easily control and navigate the unit, enhancing productivity and efficiency on the job site. Additionally, the MZ2661K boasts an adjustable cutting height, enabling users to customize their mowing experience based on specific lawn conditions.

The 872502G model is another powerful asset in the Woods Equipment lineup. This model is particularly notable for its advanced cutting technology, designed to ensure a clean and precise cut on every pass. It comes with an optimized blade design that enhances cutting efficiency while minimizing friction and wear. The 872502G also features a robust gearbox that ensures smooth operation under various loads, making it perfect for tackling tough grass and uneven terrain. Moreover, its easy-to-torque settings allow operators to fine-tune the mower to suit their preferences and specific tasks.

Lastly, the 872500G is designed for those seeking a lightweight yet efficient solution for their mowing needs. This model is engineered with agile maneuverability, making it ideal for navigating tight spaces and intricate landscapes. Its compact design does not compromise on power; the 872500G maintains exceptional cutting performance while being easy to transport and store. It includes a durable construction that promises longevity and resilience, even with regular use.

In summary, the Woods Equipment MZ2661K, 872502G, and 872500G models showcase the perfect mixture of advanced features, reliable technologies, and durable characteristics. From powerful engines to user-friendly controls and adaptable cutting heights, these machines are designed to meet the demanding needs of modern landscaping and agricultural practices. Each model caters to different user requirements while ensuring top-notch performance and reliability, solidifying Woods Equipment's reputation as a trusted leader in the industry.
Top Page Image Contents