Packing List each speaker, Tools Needed

between the two speakers (fig.1). To get an idea how they will look in the room, try taping the supplied cutout templates to the wall. Keep in mind that room furnishings play an important role in absorbing and reflecting soundwaves. Midrange and high frequencies in particular will be absorbed by soft furnishings such as sofas, carpets and curtains. A large num- ber of these soft furnishings will dull the sound, while a “live” room with few furnishings will brighten the sound. As the SuperOne Ci is not magnetically shielded, do not install it in a location where it will be within 18” of a television. Unshielded magnets placed in close proximity to a television screen can cause picture discoloration and eventually damage the pic- ture tube. When installing three SuperOne Ci’s for front channels in a home theater system, you can position the L & R speakers farther apart to create a wider soundstage. When installing a SuperOne Ci as a center channel speaker, it should be installed at least 18” directly above the location where the television will be.

Packing List (each speaker):

“SuperOne Ci” pack includes:

(1) Baffle with drivers

(6) 4 x 16mm panhead screws

“Bezel and Grille” pack includes:

(1) Bezel

(1) Metal grille

(6)4 x 16mm flathead screws

(6)Small foam rubber absorbers

(6)Large foam rubber absorbers

“Mounting Bracket” pack includes:

(1)Mounting bracket

(2)Mounting wings

(4)5 x 50mm flathead screws

(1)Cutout template - paint shield

Tools Needed:

#2 Philips screwdriver Pencil

Tape measure

Utility knife or keyhole saw Level

Wire strippers Safety goggles Protective gloves

Tech Tips: Pre-Wiring for New Construction

1.For best results, avoid running speaker cable near electrical wire, as it may induce a 60Hz hum in the audio signal. It’s a good idea to run the speaker cable after the electrical wiring has already been completed, so that you can route the speaker

cable at least three feet away from the electrical wiring. If speaker cable and electrical wiring must run parallel, install the cable within a metal conduit. Note that low-voltage wiring (doorbell, intercom, telephone, security, etc.) are unlikely to induce hum and can typically be run parallel to speaker cable with no detrimental effects.

2.When drilling holes through wall studs or ceiling joists, use a drill bit that is at least as wide as the speaker cable that will be routed through them. Always drill through the center of the stud or joist. If the hole must be drilled within one inch of the edge of a wall stud, add a nail plate to the drywall side to protect the cable from possible nails and screws put in the wall later. Line up the holes in the studs or joists as you go, so that pulling the cable through them will be easier.

SuperOne Ci specifications

The NHT SuperOne Ci is an innovative and versatile loudspeaker designed to cater to the audio demands of home theater enthusiasts and audiophiles alike. Combining elegance with advanced technology, the SuperOne Ci is designed to deliver an unparalleled listening experience while seamlessly integrating into various environments, from contemporary living spaces to traditional setups.

One of the standout features of the NHT SuperOne Ci is its compact design. The speaker is engineered for a smaller footprint, making it ideal for users with limited space. Despite its size, it doesn’t compromise on sound quality. The SuperOne Ci is equipped with a 5.25-inch woofer, providing deep, resonant bass response. Accompanying this is a 1-inch soft dome tweeter that ensures clear and articulate high frequencies, allowing music and dialogue to shine through with remarkable clarity.

The SuperOne Ci utilizes a unique acoustic suspension design, which optimizes the speaker’s performance, delivering tight bass and a balanced tonal range. This feature is particularly beneficial in smaller rooms where excessive bass can lead to muddiness. The speaker also has a frequency response range that extends from 70 Hz to 30 kHz, ensuring it reproduces a wide array of sonic details, from subtle nuances to impactful soundscapes.

Moreover, the NHT SuperOne Ci is engineered with advanced materials for durability and performance. The cabinet is constructed from high-quality MDF to reduce resonance and unwanted vibrations, resulting in a clearer sound profile. The speaker’s finish options, including sleek black and sophisticated white, allow it to complement any décor seamlessly.

In terms of connectivity, the SuperOne Ci is designed for versatility. It can be easily integrated into existing home theater systems, making it perfect for both stereo and multi-channel setups. With its 8-ohm impedance, the speaker is compatible with a wide range of amplifiers, ensuring that users have flexibility no matter their audio source.

Lastly, NHT’s commitment to quality control and sound engineering is evident in the SuperOne Ci. Each unit undergoes rigorous testing to guarantee consistent performance and reliability. This attention to detail makes the NHT SuperOne Ci not only a great entry point for listeners new to high-fidelity audio but also an exceptional choice for seasoned audiophiles seeking a compact speaker solution.