NHT SuperOne Ci manual

fig.7

fig.8

Installation: Existing Construction (retrofitting finished walls)

Warning: Exercise caution when drilling into existing walls. Do not drill through existing wires, pipes, conduits, heating or air conditioning ducts. If you feel resistance while drilling, stop immediately.

1.Using a studfinder or the “knocking” method, locate the wall studs in the wall area where you wish to mount the speaker. The speaker will be mounted between adjacent studs, no closer than two inches from either stud (fig.7).

2.Determine that there are no obstructions behind the desired cutout area. This may be accomplished by drilling a hole in the center of the cutout area and using an “L”-shaped piece of metal (like a coat hanger) to “feel around” behind the wall. If you discover an obstruction, fill the hole with patching compound and try anoth- er location.

3.If there are no obstructions found behind the wall, use the supplied cutout tem- plate and a pencil to draw a 12-1/8”H x 8”W outline of the area to be cut out. Use a level to ensure that the cutout is precisely positioned. Begin by drilling the four corners with a 1/4” bit (fig.7). Then cut out the wall section with a utility knife or keyhole saw, following the lines traced around the mounting template. If the wall is painted or wallpapered, use the keyhole saw.

4.If the wall is constructed of lath and plaster, outline the penciled marks with masking tape, drill the four corners with a

1/4” drill bit, and use a utility knife to cut through the plaster down to the lath. Use a saber saw with a metal cutting blade or a pair of tin snips to gently cut through the lath, being careful not to vibrate plaster off the wall.

5.Insert the SuperOne Ci mounting bracket diagonally through the cutout in the wall, then pull forward into position. If the cutout was cut correctly according to the cutout template, the bracket should fit snugly into place. The plastic tabs on all sides of the bracket will rest flatly against the back side of the wall (fig.8).

6.While holding the bracket flatly against the rear side of the wall with one hand, attach the bezel to the bracket with six 4 x 16mm flathead screws that line up with the six raised bosses on the bracket (fig.9). If the bezel is not installed in the prop- er orientation, all six screw holes will not line up. Tighten screws snugly, making sure not to over-tighten, as this may compromise the fit of the bezel. The use of power screwdrivers is not recommended. The absorptive strips on the back of the bezel’s outer frame prevent unwanted vibrations against the drywall, and will com- press slightly to allow the frame to rest flush against the wall on all four sides. When installed correctly, the bracket and bezel “sandwich” the drywall.

7.If the SuperOne Ci bezel frame and grille are to be painted in the wall, paint

fig.9

fig.10

SuperOne Ci specifications

The NHT SuperOne Ci is an innovative and versatile loudspeaker designed to cater to the audio demands of home theater enthusiasts and audiophiles alike. Combining elegance with advanced technology, the SuperOne Ci is designed to deliver an unparalleled listening experience while seamlessly integrating into various environments, from contemporary living spaces to traditional setups.

One of the standout features of the NHT SuperOne Ci is its compact design. The speaker is engineered for a smaller footprint, making it ideal for users with limited space. Despite its size, it doesn’t compromise on sound quality. The SuperOne Ci is equipped with a 5.25-inch woofer, providing deep, resonant bass response. Accompanying this is a 1-inch soft dome tweeter that ensures clear and articulate high frequencies, allowing music and dialogue to shine through with remarkable clarity.

The SuperOne Ci utilizes a unique acoustic suspension design, which optimizes the speaker’s performance, delivering tight bass and a balanced tonal range. This feature is particularly beneficial in smaller rooms where excessive bass can lead to muddiness. The speaker also has a frequency response range that extends from 70 Hz to 30 kHz, ensuring it reproduces a wide array of sonic details, from subtle nuances to impactful soundscapes.

Moreover, the NHT SuperOne Ci is engineered with advanced materials for durability and performance. The cabinet is constructed from high-quality MDF to reduce resonance and unwanted vibrations, resulting in a clearer sound profile. The speaker’s finish options, including sleek black and sophisticated white, allow it to complement any décor seamlessly.

In terms of connectivity, the SuperOne Ci is designed for versatility. It can be easily integrated into existing home theater systems, making it perfect for both stereo and multi-channel setups. With its 8-ohm impedance, the speaker is compatible with a wide range of amplifiers, ensuring that users have flexibility no matter their audio source.

Lastly, NHT’s commitment to quality control and sound engineering is evident in the SuperOne Ci. Each unit undergoes rigorous testing to guarantee consistent performance and reliability. This attention to detail makes the NHT SuperOne Ci not only a great entry point for listeners new to high-fidelity audio but also an exceptional choice for seasoned audiophiles seeking a compact speaker solution.