Attaching the Clutch Cable

Slot Head Screw,

Nut, Flat Washers

Internally Threaded

Tube

Plastic

Figure 4

Attach the clutch cable to the handle as follows (be careful not to kink the cable).

•Remove threaded eyebolt and nut from the end of the cable.

•Route the clutch cable to the right side of the handle mounting brackets and underneath the handle.

•Push the cable through the hole in the center of the handle and snap in the plastic fitting. See Figure 4.

•Remove slot head screw, nut and two flat washers from the clutch bail.

•Fasten the threaded eyebolt onto bail as shown in Figure 5. The parts go together from top to bottom as follows: Slot Head Screw, Flat Washer, Clip, Eyebolt, Flat Washer and 1/4” Nut.

•Thread eyebolt and #10 nut, removed in step 1, into the internally threaded tube at the end of the cable. Thread engagement should be about 3/4”. Tighten nut against tube at end of cable. See Figure 5.

Clutch		Slot Head Screw
Clutch
Bail		Flat Washers
	Threaded	1/4”
	Threaded	Nut
	Eyebolt	Nut
	Eyebolt
	#10
	Nut	Internally
		Internally
		Threaded
		Tube

Figure 5

NOTE: Do not overtighten clutch cable. Too much tension may cause it to break.

WARNING: Be certain to check the clutch cable adjustment as instructed on this page before operating the tiller.

Secure clutch cable to handle using cable tie. Refer to Figure 7. Cut off excess end of cable tie.

ATTACHING THE CONTROL ROD

•Remove hairpin clips from control rod, (rubber washers to remain on control rod).

•Insert the shorter, (angled), end of the control rod through the indicator bracket on the shift cover and secure with hairpin clip that was removed in step 1. See Figure 6.

•Insert the longer end of the control rod through the hole in the gear selector handle and secure with

hairpin clip.See Figure 7.

	Control Rod
Rubber
Washer
Idler
Pulley	Indicator Bracket
Rod	Hairpin
	Hairpin
	Clip

Figure 6

CHECKING THE CLUTCH ADJUSTMENT

IMPORTANT: Service the engine with oil and gasoline before checking this adjustment. Refer to the separate engine manual packed with your tiller for proper fuel and engine oil recommendations.

Position the tiller so the front counterweight is against a solid object, such as a wall. With the gear selection lever in NEUTRAL, start the engine. Refer to the separate engine manual.

Standing on the right side of the tiller, examine the belt (inside the belt cover). It should not be turning.

NOTE: Do not put fingers under the belt cover.

If the belt turns without bail engaged, adjust by unthreading the internally threaded tube at the end of the cable a few turns clockwise (when standing in operator’s position), and then retighten the nut against the tube.

RT65 specifications

The Yard-Man RT65 is a versatile and robust lawn tractor designed to meet the mowing and gardening needs of homeowners with medium to large properties. Equipped with a powerful engine and a series of features, it’s built for efficiency and ease of use, ensuring that every cutting session is both productive and enjoyable.

One of the most notable features of the Yard-Man RT65 is its 65-inch cutting deck. This generous size allows for a wider swath of grass to be cut in a single pass, significantly reducing mowing time. The cutting deck is made from durable materials that withstand the rigors of regular use, providing longevity and reliability to the user. The adjustable cutting height feature gives homeowners the ability to customize the grass length according to personal preferences and seasonal requirements.

The RT65 is powered by a robust engine, usually a dependable Briggs & Stratton or a similarly positioned manufacturer. This reliable engine ensures sufficient power to tackle tough mowing tasks, while maintaining fuel efficiency. The tractor is designed with user comfort in mind, featuring an ergonomic seat that provides a comfortable ride even during extended mowing sessions. The controls are intuitively placed, allowing for seamless operation without distraction.

In terms of technology, the Yard-Man RT65 boasts an automatic transmission system, offering a smooth driving experience. This feature allows the mower to adjust its speed seamlessly, making it easier to navigate through varying terrain. The turning radius is also commendable, enabling homeowners to maneuver around tight corners and obstacles in the yard with ease.

Safety features are a priority in the design of the RT65, which typically includes a parking brake and a safety cut-off that stops the blades when the operator leaves the seat. This ensures peace of mind, especially when children or pets are present in the vicinity.

Moreover, the RT65 is compatible with various attachments and accessories. Whether it's a bagger for grass clippings, a snow plow for winter maintenance, or a mulcher for given lawn care treatment, the versatility of this lawn tractor makes it a multi-functional tool for year-round yard work.

In summary, the Yard-Man RT65 combines power, efficiency, and user-friendly features in a compact package. Its impressive cutting capability, reliable engine, and thoughtful design characteristics make it a valuable addition to any homeowner's lawn care arsenal, ensuring well-maintained lawns with minimal effort.