Operating Instructions Controls | Yazoo/Kees ZKHP61253, ZKHP52233

ADJUSTMENTS

MOTION CONTROL LINKAGE ADJUSTMENT:

1.This adjustment must be made with the drive wheels rotating. Raise rear of the unit and block it up so the wheels are free to rotate. CAUTION: Keep hands, feet and clothing away from rotating tires.

2.Tilt seat forward and remove the seat rod from seat so the seat can rotate down onto the frame. Make sure the seat is adjusted toward the rear of the unit so it clears the controls on the console.

3.Place a 2x4 board approximatly 10 to 12 inches long between the foot plate and the center of the seat to engage the seat safety switch. NOTE: You may want to cover the end of the 2x4 with a rag to protect the seat from marring.

4.The reverse spring detent must be adjusted correctly before the motion control linkages may be adjusted.(See reverse spring detent adjustment section.)

5.Loosen the nuts directly behind each ball joint on both rods that connect the pump arm to the motion control assemblies. (See Fig 5 )

6.Start the engine. The park brake must be engaged and the motion control levers must be in the neutral slot (See figure 6 page10) to start the engine. Run engine at approximately 1/

2throttle.

7.Release park brake to allow wheels to rotate. CAUTION: Keep hands, feet and clothing away from rotating tires.

8.Begin with either side and put the motion control lever into the neutral position. Adjust the motion control linkage by rotating the double nuts on the rod in the proper direction until the wheel stops rotating (See Fig 5 ).

Move the motion control lever forward then into the neutral position and place it into the neutral slot. The wheel must be stopped completely at this point. Now do the same in reverse and release the lever. The lever should return to neutral on its own. If not see reverse spring detent adjustment section.

9.Run engine at full throttle to make sure wheels do not rotate. Readjust if any rotation occurs.

10.Repeat on the opposite side and tighten nuts against ball joints.

11.Remove the 2x4 board and make sure the seat wiring is connected to the wiring harness. WARNING: Seat must be connected for safety interlock system to properly function.

OPERATING INSTRUCTIONS

CONTROLS:

1.Be thoroughly familiar with all controls their function and how to operate them before operating the mower.

2.Motion control levers located on each side of the console control direction of movement. The left lever controls the flow of oil from the left hydro pump to the left wheel motor. The right lever controls the flow of oil from the right hydro pump to the right wheel motor.

ZKW61233, ZKH52223, ZKW52233, ZKH52253, ZKHP52253 specifications

The Yazoo/Kees ZKHP52233, ZKHP52253, ZKW52233, ZKH61253, and ZKH52253 stand out in the landscape of compact and efficient commercial mowers. These models are designed to meet the demanding needs of landscape professionals, offering a combination of power, precision, and adaptability.

One of the main features of these mowers is their robust engine performance. Each model is equipped with powerful engines that provide consistent torque and speed, enabling them to tackle dense grass and tough terrain efficiently. The engines are engineered for reliability, ensuring that they can operate under heavy loads without compromising performance.

The ZKHP52233 and ZKHP52253 model lines showcase a high-performance hydrostatic drive system. This technology allows for smooth acceleration and responsive handling, making it easier for operators to navigate tight spaces and challenging landscapes. The hydrostatic transmission also contributes to reduced wear and tear, prolonging the lifespan of the mower.

The cutting decks across these models are designed for superior performance. The ZKHP52233 and ZKW52233 feature adjustable cutting heights, providing versatility for different types of grass and landscaping needs. The cutting width is optimized for efficient mowing, allowing operators to cover larger areas in less time while ensuring a clean, even cut.

Ergonomics play an essential role in the design of these mowers. The operator's station is thoughtfully crafted to minimize fatigue during long working hours. Features such as adjustable seats, intuitive controls, and vibration-reducing components enhance user comfort. The ZKH61253 model takes this a step further with a more spacious platform, accommodating operators of various sizes comfortably.

Additionally, the durability of these mowers is notable. Constructed with high-quality materials and reinforced frames, they are built to withstand the rigors of commercial use. The rust-resistant components ensure longevity even when exposed to various weather conditions.

In terms of maintenance, Yazoo/Kees has implemented user-friendly features that simplify regular upkeep. Accessible service points and easy-to-replace parts allow for quick maintenance, ensuring that these mowers run at peak performance day in and day out.

Overall, the Yazoo/Kees ZKHP52233, ZKHP52253, ZKW52233, ZKH61253, and ZKH52253 embody a perfect blend of power, efficiency, and user-centric design. These mowers are tailored to meet the needs of commercial landscapers, providing the tools necessary to excel in a competitive environment while ensuring the highest standards of performance and reliability.